Week 9 - Challenge 3 - Bumper

Automotive Wiring Harness Project 2 Aim      Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available…

Wiring Harness using CATIA V5 -  Project 1 Routing for side door panel       Connector Selecting First we need to check whether the Connectors are provided by the supplier . If not we need to decide the type of connector that is required as per the varies specifications The decision is made by considering…

Your Answers Answer: The given Connector are first downloaded from the TE.com, the following connectors are DT06-4S DT06-6S DT06-2S DT06-08SA And This connector are opened in the Catia V5 where we need to define them in Electrical DT06-2S WorkBench: Part Design First we need to create 2 points on the ends And on the connector…

1.Bundle Connectivity 2.Annotations   3. Error The Error has be obtained while bundleing the connector 4  so i just repositon the connector 4 which is shown in the figure 4.CATPRODUCT to igs

Week 12- Final project     SIDE DOOR TRIM  LOWER SUBSTRATE FINAL TRIM DRAFT ANALYSIS           ISOMETRIC VIEW               RIGHT SIDE VIEW                          LEFT SIDE…

Week 11 - Project - A pillar Design with Master Section   Geometrical set   Final Trim    Dog house and Ribs Final part draft analysis    Master Section Verification  

Heat Stakes And locators Challenge Geometrical Set Closed Surface    Heat Stakes and locators Final Draft Analysis for the Assembly   

Dog house  Creation Challenge Geametrical Set Draft Analysis For the Closed Surface    Draft Analysis for Final part with Dog House   

Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)    Draft analysis for the final part      

Bumper Geometrical Set Draft Anlaysis for Class A     Draft Analysis for Final Closed Surface    Closed Surface

Switch Bezel Geometrical Set Draft Analysis for Class A surface    Draft Analysis for Final product    Closed Surface  

                      Class A Surface Draft Analysis on Class A Surface      Draft Analysis on Final Part Body                                       …

Drawing 1 Drawing 2

Answer: The given Connector are first downloaded from the TE.com, the following connectors are DT06-4S DT06-6S DT06-2S DT06-08SA And This connector are opened in the Catia V5 where we need to define them in Electrical DT06-2S WorkBench: Part Design First we need to create 2 points on the ends And on the connector connection…

Answer: P Clamp         A clamp is a fastening device used to hold or secure objects tightly together to prevent movement or separation through the application of inward pressure. Part Design First need to create 2 points on both sides of the clamp create a planes on the 2 surfaces of the…

Answer: 1.Deutsch DT06 – 08SA The Connector is downloaded from the Te.com  It is opened in the Catia software Part Design There are various workbenches in the software , first we need to go with the part design model Creation of points on both the ends Creation of the axis on the mating side of the Connector Axis Consideration…

Aim:        To connect 10 cell series lithium ion battery model and to  simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. Answer:           The tablebased battery is used in this model, …

Aim:   To Prepare a detailed battery pack drawing along with its enclosure Given Data: Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Solution:           The Battery needs to be designed which we need to consider from the bottom level of selection of cells to the end of the battery,…

Answer:1. Battery management system  A battery management system (BMS) is any electronic system that manages a rechargeable battery (cell or battery pack), such as by protecting the battery from operating outside its safe operating area, monitoring its state, calculating secondary…

1.Answer: Lithium Ion Batteries               Lithium ion batteries are the most used batteries in the current generation due to its high Specific energy compared to other lead and zinc batteries. Lithium ion batteries work by using the transfer of lithium ions and electrons from the…

Solution: To modle the development of a forward energy-based fuel consumption model of a P1 hybrid vehicle.  In this model we have both the domains of the Electrical (Motor) and the Mechanical (Engine)are connected in series to the crankshaft, which is why it is called as the P1 Hybrid Vehicle. We will be using two…

  Explanation: The Matlab program has been downloaded from the above file. The Engine and the vehicle dynamics are Empty, which we need to get It done. The detailed Engine section has been explained below. Engine Here the input is the Engine speed which is given to the 1D look table which consist of the required torque…

Develop a double-acting actuator model using Simscape Multibody and Simscape components. The mechanical system of the cylinder needs to be built using Simscape Multibody library components / blocks, and the hydraulic system needs to be modelled using Simscape library physical components. Solution: Here we want to construct…

The equation is pasted below, which is obtained by means of the kirchoffs law for the Dc motor unit and by means of Newtons law for the load.   The final equation is given below. w(s)/v(s) = Kt/{(L s+Ra)(Js +B)+Kt*Kb] The matlab script is given below %This file contains design paramaters to model a DC motor. J=0.01; %…

PROGRAM %%Data handling project a=xlsread('VI.xlsx');%to get the from the excel v=a(:,1);%for assuming v as voltage i=a(:,2);%for assuminf i as current z=[-17.3:0.1:0.9];%data required from this range yq1=interp1(v,i,z); yq2=interp1(v,i,z,'spline'); plot(v,i,'o',z,yq1,'m-'); plot(v,i,'o',z,yq2,'b'); grid; save yq1.txt;…

1.Ans:MAJOR ELEMENTS IN THE DIAGRAM: Starter Battery  Ammeter Fuse  Igniation coil Distributer Generator 2.Ans: BATTERY It is one of the important device, which is used to provide the current to whole system. It is responsible for the ignition, by which the spark is produced for all the cyclinders. It is all used to store…