Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1

 ABOUT LENS Lens is an optical material that controls the light emitted from a light source and allows it to distribute in a certain angle and density. Lenses provide precision control over light angle. Lenses can be made of plastic, silicon or glass material in various shapes and sizes.      …

 ABOUT LENS Lens is an optical material that controls the light emitted from a light source and allows it to distribute in a certain angle and density. Lenses provide precision control over light angle. Lenses can be made of plastic, silicon or glass material in various shapes and sizes.      …

Project 2: Back Door Wiring Harness Assembly:   Objective: Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Back Door Assembly…

Aim: To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as…

AIM- To prepare a flattened view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals on the…

          AIM:       Route two electrical harnesses are per the given layout and interconnect them as a single harness assembly and then ckeck for bundle continuity, bundle warnings, and then give annotations to the final harness assembly. OBJECTIVE:       1) The objective…

        Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps…

                                                                    TITLE:Wiring harness routing & packaging Rules Week 3 Challenge    …

AIM: To define Electrical properties of the given components.   OBJECTIVE: To download the above CAD data of the parts from the given source. To define the Electrical properties correctly. To create catalogues of the components so that it can be used later.   SOLUTION METHODOLGY:     PART - 1: DEUTSCH…

                         TITLE:DESIGN OF BACK DOOR   Aim: To design the back door inner panel and the Hinge, Gas stay, Wiper motor and Latch reinforcements according to the engineering standards and given design considerations. Introduction: Backdoor is a sheetmetal component and plays major role in BIW components of an…

                         TITLE:DESIGN OF BACK DOOR   Aim: To design the back door inner panel and the Hinge, Gas stay, Wiper motor and Latch reinforcements according to the engineering standards and given design considerations. Introduction: Backdoor is a sheetmetal component and plays major role in BIW components of an…

TITLE: ROOF DESIGN   INTIDUCTION The roof of a car or other vehicle is the top part of it, which protects passengers or goods from the weather. The roof also protects the passenger from any injury when the car gets crashed or is rolled over or something heavy falls on the roof. OBJECTIVE The mian objective of this project…

                              TITLE: FENDER DESIGN OBJECTIVE : The main objective of this project is to design a fender using  a new age design software - NX - CAD INTRODUCTION : Fender is the US English term for part of an automobile…

                                    TITLE:FENDER DESIGN-WHEEL ARCH AIM Study the Wheel Arch area and prove whether the car will pass the standards or not using European regulations.   Introduction Wheel arch comes with some standard…

AIM To Use the Section from Hood design and calculate the Section Modulus using the formula  S = I/y  Where,  S = Section Modulus I = Moment of Inertia y = distance between the neutral axis and the extreme end of the object    PROCEDURE: The data are collected from taking the master section using the mid plane Front crash…

                                                                 TITLE:HOOD DESIGN Objective Design hood outer panel, inner panel and reinforcements with the…

Introduction:   What is underbody coating for automobiles?    Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting…

AUTOMOTIVE BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance Automotive Benchmarking is the process of analyzing the choices of similar products based on the selection factor and deducing it to final conclusion. CASE Mr. D.S. Pughazhyendhii is a married man…

                                                    TITLE: FINAL PROJECT   AIM: To design the car door inner panel with reference to given Class-A surface by using given mastersection,…

                                                                                           …

Title: Door Trim Lower with Engineering features Using CATIA V5 Objective: To create the Door Trim Lower Plastic component with Engineering Features through the given Class-A surface. As well as, creating the tooling axis for the given Class-A Surface which is meeting the requirements of the draft angle and at…

TITLE:DOOR TRIM CAT PART FOR DOG HOUSE   Aim :- To design the Dog House for the Door Trim considering the design rules.   Objective :- To create a proper tooling direction. To perform a draft analysis of the plastic component. To design the Door Trim plastic component by creating the B-Surface…

Attachment Feature Creation (Ribs & Screw Boss) AIM Create the rib for the Drill Handle considering the design rules. INTRODUCTION Ribs and screw bosses are engineering features which are created on the B side of the plastic components. RIBS Ribs are used to strengthen the walls of your mould without increasing wall thickness…

                                                                                           …

                                                                   TITTLE: BUMPER AIM:Bumper plastic component design usin CATIA V5 OBJECTIVE: create…

                                                           TITTLE: COIN HOLDER AIM:Coin holder plastic component design usin CATIA V5 OBJECTIVE: create center console…

                                                                                        Title: Base Bracket Design Aim: To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component   Objectives:  Creation of Tooling Axis. Creation of Class B and Class…

                                                                                  Title: SWITCH BEZEL   Aim: To…