Week 7-12-Creation of 1D Connectors Challenge

  Project-2-Meshing of Door Inner Panel Challenge Question Rules Grading Policy   Follow the Quality Criteria and mesh the following component and assign thickness: Target Element Length = 4 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper     …

AIM -  For this challenge, you will have to mesh the given geometry. Provided below are the quality parameters that you have to follow. Target Element size - 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45…

     AIM  For the given MODEL 1, Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15   For the given MODEL 2, Create a 3D…

AIM -  Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad…

AIM- For this challenge, you will have to mesh the backdoor geometry of a car that is provided below. Provided below are the quality parameters that you have to follow. Target Element size - 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5…

AIM - Generating the mid surface and do the geometry cleanup for the given component after generate the mesh on the component with proper meshflow and pass the model of given quality criteria. Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units…

AIM-: Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm                  …

AIMFor the given Intake Manifold component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.  S.No  Quality Criteria  Value  1 Target/Average length   3 2 Minimum Length  1 3 Maximum Length  5 Use tetra elements to mesh…

  Aim: Performing Geometry Clean-up and remove any topological error, extracting mid-surface of every part,mesh with the given quality criteria and assign thickness,than draw model as solid.  Methodology: The methodology for the given element is as follows: Import geometry and delete…

AIM - For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria)  S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  2 3 Maximum Length …

Week - 8 - Morphing Aim:To do morphing for the given CAD model using ANSA. procedure:- CAD Model. Clean geometry. Morphing.   Morphing:-Morphing is one of the ANSA feature which is used to change the shape of the model without changing the numerical values. Transforming the whole shape will take lot of time and…

Aim: The aim is for the given Rear door FE model, Create and Apply different PIDs for different componentsa and to perform suitable connections.  Procedure: Type Of Connection in ANSA- Rigid- RBE2 AND RBE3. Seam Weld-Y-Joint weld And Overlap Weld. C-Bush Element. Spot Weld Creation. Bolt.    CAD MODEL- The…

 AIM-:In this challenge we will work on rear view mirror. Here we will check the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.  S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length …