Week 11 - Project - A pillar Design with Master Section

Report:  The aim of this project is to devise a butterfly valve and implement Geometric Dimensioning and Tolerancing (GD&T) to its constituent parts and final assembly using Siemens NX software. Introduction: A butterfly valve belongs to the family of quarter-turn valves. During operation, the valve achieves complete…

AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Wiring harness routing shall provide ease in manufacturing, accessibility,…

AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Wiring harness routing shall provide ease in manufacturing, accessibility,…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. HARNESS ASSEMBLY: HARNESS FLATTENING:…

Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download connector 3D data…

The given clip was downloaded and opened as a part file. I have to define two points that will be used as entry and exit points. Then a plane has to be defined at the points. A base plane has to be defined at a distance of 2 to 3 mm from the clip. again we define the exit point at the first definition as the entry point.…

CONNECTOR DEFINATIONS IN CATIA V5 1. Deutsch DT06 – 08SA Connector connection point             Create midpoint on the contact face which will be normal to wire bunddle insertion. Craete Axis System with respect to the point which we have created and defining the axis direction as shown below Bundle connection point: Switch…

1. Introduction The Back Door Design project in NX CAD Sheet Metal aims to create a structurally sound and visually appealing back door for a vehicle. This report outlines the design methodologies employed, explains the development of key components, illustrates the integration of provided styling surfaces, and concludes…

1. Introduction: The design of a car roof is a crucial aspect of automotive engineering, ensuring safety, aerodynamics, and aesthetics. This report presents a comprehensive design of a car roof using NX CAD Sheet Metal, incorporating key components such as the Front Roof Rail, two Bow Roofs, the Center Roof Rail, and the…

1. Introduction: The fender is an essential component of a vehicle that protects it from debris and enhances its aesthetic appeal. This report aims to explain the design process of a front fender in sheet metal using NX CAD. The focus will be on the different mounts, manufacturing process, and key design parameters involved…

Section modulus is a geometric property used to measure the resistance of a cross-sectional shape, such as a beam or a column, to bending. It provides information about the shape's ability to withstand bending stresses and is crucial in structural engineering and design. The section modulus is defined as the ratio of the…

Introduction The purpose of this report is to provide a detailed explanation of the design and manufacturing process for the hood of a vehicle. The hood is an essential component of a vehicle's exterior, providing protection for the engine and other vital components. This report will cover various aspects of the hood design,…

Under-body coating, also known as undercoating, is a protective layer applied to the underside of a vehicle to provide additional defense against corrosion, rust, and damage caused by various environmental factors. It is commonly used in the automotive industry to extend the lifespan and maintain the structural integrity…

WHAT IS BENCH-MARKING?   Benchmarking in the automotive industry refers to the process of comparing a company's products, processes, or performance metrics with those of its competitors or industry leaders. It involves gathering data, analysing it, and identifying areas where a company can improve or learn from others…

"This is a challenge about making RIBS and SCREW BOSS on a surface. First, I have to create a Tooling Axis by extracting a surface and creating a line through a point. Then, I have to convert the Class A Surface to a Class B Surface. Next, I need to create the Ribs. To do so, I must extract another surface, create a line,…

    Use the "Create Reference Element" command to create a reference line that bisects the bumper into two halves. Use the "Create Axis" command to create a rotational axis that runs along the reference line. Adjust the axis orientation and position until it aligns with the draft angle required for the part.…

First Drawing is complete sorry for the 2nd drawing, i have no time left