Week 11:- 2D Detailing Challenge 2

                                 Week 9 Challenge Mold design - CPU fan case - Part 2 Input design:    Introduction: This report details the process of mold design and creation of sliders for the CPU fan case using SolidWorks…

Input design:      Introduction: This report details the process of mold design and creation of sliders for the Table Fan Base using SolidWorks software. The aim of this project was to develop an efficient and effective mold design to produce high-quality Fan Base with optimal functionality and aesthetics.…

                                                        Week 7 Challenge - Slider Creartion   Input design:    Abstract: This report outlines the mold block design process…

N/A

.

                                                      Week 12:- Documentation Challenge   Aim :- Create a BOM and Hardware list (BOP) for the complete Fixture assembly…

                                                            Week 11:- 2D Detailing Challenge 2     Aim :-  1) Create 2D Drawing for each Clamp Units with…

                                                              Week 10:- 2D Detailing Challenge   Aim -  Draft a Key Sheet for the Complete Fixture…

                                                        Week 8:- 3D Finishing Challenge 2     Aim - Perform 3D finish and create Rough locators for…

                                                    Week 9:- 2D Detailing Challenge     1) What are the Drawing templates?   Drawing templates are typically created by a user…

                                                Week 8:- 3D Finishing - Challenges 1   1) What do you understand by the 3D finish process? The 3D documentation for a BIW fixture design…

                                         Week 7- Base Unit Design Challenges 2 Aim - Design a Base Unit for the units designed for the above challenges with all weldments for the given…

                                                Week 7:- Base Unit Design Challenges 1          1) What is the Base Unit? What are the typical parts of the Base Unit? a base…

                                                Week 6:- Clamp Unit & Pin-Clamp Unit Design Challenge     AIM - Design 3 Different types of Swivel Clamp Unit with Different Riser, Blade,…

                                                   Week 5:- Rest Unit & Clamp Unit Design Challenge Aim :-  Design 3 Different types of Power Clamp Unit with Different Riser, Blade…

                                                          Week 4:- Pin Unit Design Challenge   Aim :-  Design of 2 Fixed Pin Units with different risers, blade,…

                                  Week 3:- BiW Fixture Design Methodologies Challenges   1) What is Design Methodology?     Purchase order :- Purshace order is a necessary documet for confirmation to start desigh or…

                                   Week 9 - Project 1 - Door Trim Lower with Engineering Features     Screenshots of the completed design in various orientations (Isometric, Front, Side, and Top View)      …

               Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1     Screenshots -  Isometric, Front, Side, and Top View                                  …

                                  Week 9 - Attachment Feature Creation - Challenge 2     Screenshots -  Isometric, Front, Side, and Top View                   Report on DRAFT…

                                               Week 8 - Challenge 6 - Core & Cavity Design   Screenshots -  Isometric, Front, Side, and Top View         Draft Analysis…

                                               Week 8 - Challenge 4 - Bumper   Screenshots -  Isometric, Front, Side, and Top View           Draft Analysis on Class…

                                                   Week 8 - Challenge 3 - Coin Holder Design       Screenshots -  Isometric, Front, Side, and Top View      …

                                           Week 8 - Challenge 2 - Switch Bezel Design     Draft Analysis on Class A Surafce.   Draft Analysis on Solid Body.            …

                                       Week 8 - Challenge 1 - Base Bracket Design   Screenshots -  Isometric, Front, Side, and Top View           Draft Analysis on class A surface  …

                                                              Week 2:- BiW Fixture Basics Challenge     1) What is the process of project execution activity?…

                                           Introduction to BiW and Fixtures   1) What is BIW & define its parts? BIW term stands for Body In White It is the stage in automobile where body shell structure…

                                                                           Title :- Odd Shaped Enclosure   Objective :-…

                                                                      Title :- Metal Bracket II     Objective :-  Design…

                                                                      Title :- Bracket design     Objective :-  Design…

                                                                      Title :- Box Assembly      Objective :- …

                                                                           Title :- Casing Design using UGNX   Objective :-…

                                          Design of backdoor Objective: Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements…

Section Modulus calculation and optimization   Section Modulus The section modulus is defined as S = I / y, where I is the second moment of area  (or area moment of inertia, not to be confused with moment of inertia) and y is the distance from the neutral axis…

                                                                Roof Design What is Roof? Roof of car is aimpotant element which protects passengers, Roof block…

                                            Fender Design - Wheel Arch Challenge   Wheel arch calcution are one of the importnat calculations to determine the wheel position from the fender. the purpose of…

                                                                                           …

                                                                                           …

                                                                     Underbody Coating   Before understanding underbody coating we have…

   What is bench marking ?  Benchmarking involves a structured comparison between similar products, services or processes on some dimensions of performance. For example it can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer…