Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork

1)ANS: 1. EQ+X IS 1893 Load-X 1 2. EQ+Z IS 1893 Load-Z 1 3. DEAD LOAD Self weight Y -1.15 Main frame rafter GY -1.55 KN/m Gable frame rafter GY -0.775 KN/m Main frame column GY -1.2 KN/m Gable frame column GY - 0.6 KN/m Gable / wind column GY -1.04 KN/m Wind frame point load FY - 1.14 KN/m Gable frame point load FY -0.57…

AIM:  To Design a multi-storey Residential Building located in Bangalore using STAAD Pro. PROCEDURE:    Wind load:  Wind presure  Pz  =  0.6 Vz^2      where Vz = Vb X k1 X k2 X K3          Vb = Wind speed at the certain location  = 50 …

1.1) ANS : The primary load cases to be considerd for the design are the Dead load Live load / Imposed load  Wind load  Earth quakeload   1.2)   ANS :  One - way slab  The ratio of the longer span to the shorter span is greater than 2 is know as one - way slab Where LY / LX…

1.1)answer: Go to properties in that select define property select circle and give the radius for the member and assign the defined circle to the member created 1.2)answer: While creating a model go to unit system and assign the units Go to geometry in that’s elect input units and assign the units ,Go to…

1.1)answer: Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for the. Std file on your machine & send it. 1.2)answer: STAAD.Pro includes a set of predefined materials for concrete, aluminum, steel,…

1)Ans:- To export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. Procedure:- open revit and the open structural or architectural file in revit and then go to file and then export to NWC and create a folder and then save the file as NWC format.export…

1) AIM: To Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. PROCEDURE: First open the revit file and then open the dynamo.  for creating the sinusoidal points we will insert the three integer sliders i.e start,end & step next we will provide the range.…

1) answer:  a. Multi-Unit Residential Apartment 2) answer: The open space around the building shall not be less than 4.5 The type of constrution as type -2 construction,the FAR value for the business building shall be taken as 2.9 Individual floor area is with in the prescribed limits. The width of the road abutting…

1) AIM: To Model a Ceiling from the architecture tab above the walls at the first-floor level. PROCEDURE: First open the revit software. draw the residential building with own dimensions. after that provide the doors & windows. next we will use the annotate tab to provide dimensions. after that using floor tab,…

1) AIM: To Create a 3 dimensional model of the residential building with a rendered view. PROCEDURE: To draw the 3d model of residential building by using 3d tools and 2d tools wherever required. first we will draw the 2d plan of the given plot. after that it will change to the 3d plane. using the extrude command…

1) AIM: To Create a 3D Isometric View of the building with plan and elevation given.  PROCEDURE: To draw the given diagram by 2D & 3D autocad tools. first we will use the absolute/rectangular coordinating method for drawing. after that we will use 3D tools wherever required. 3D ROTATE,EXTRUDE tools also used…

1) AIM: To Create a 3D Furniture element as shown in the Figure. PROCEDURE: To draw the given diagram by 3D autocad tools. first we will use the absolute/rectangular coordinating method for drawing. after that we will use 3D tools wherever required. 3D ROTATE,EXTRUDE tools also used for the drawing the above diagram. Result:…

1) AIM: Create a layout of the Plan and Section A of the project in Challenges 7. PROCEDURE: First we will create the new layout for the project. after that we will setup the page i.e A1,A2,A3,A4....etc. using the MV,MS&PS commands for the setup of the layout. after that we will use scale wherever required. next…

1] Aim: To draw the given diagram by the drafting tools. Procedure :  By using the drafting tools we will draw the above diagram Before the draw the diagram we will setup the units and limits. first we start with X-line i.e horizontal and vertical lines. after that using the drafting tools i.e offset,fillet,trim,extend…

1] Aim: To draw the given diagram by the drafting tools. Procedure :  By using the drafting tools we will draw the above diagram Before the draw the diagram we will setup the units and limits. first we start with X-line i.e horizontal and vertical lines. after that using the drafting tools i.e offset,fillet,trim,extend…

1)   AIM: To create a Architectural Drawing (Floor Plan, Elevations, and Sections) for given plot size.   Procedure :  By using the drafting tools we will draw the above diagram Before the draw the diagram we will setup the units and limits. first we start with X-line i.e horizontal and vertical lines.…

Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code. Different Load Calculation on Column, Beam, Wall & Slab Column = Self  Weight x Number of floors Beams = Self Weight per running meter Wall Load Per Running Meter Total Load on Slab (Dead Load + Live Load +Wind Load…

Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash Ans:- a) Grade designation : M35b) Type of cement : OPC 53 Grade conforming IS 12269c) Maximum nominal size of aggregate : 20mmd) Minimum cement content : 340 kg/m3 (IS 456:2000)e) Maximum water-cement ratio…