Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class

AIM-

To Export the Revit architecture and structure model to Navisworks Coche le following the export settings

INTRODUCTION

• Navisworks Cache Files are created mostly for ease of use and speed
• When you open a model created in other programs, it creates a cache file that is much smaller in size and you won't even notice it
• The next time that you open that same model, it wil instantly part rather than gathering the information for it
• This is because it is now reading the information from the cocte file rather than the model isod (so long as the original file isn't newer than the cache file in which case it will re-cache and replace the old one). it does this for each file Navisworks opens or merges natively.

PROCEDURE

Step-1

• first we have to open the revit software and open the architectural model
• Het we click on the file option and export the model as NWC fije, as shown in the below figure fint the export scene os tab will appear ned the give the nec file name as project

Step:-2

• Next we have to open the revit software and open the structural model.
• Next we click on the file option and export the model as NWC file, as shown in the below figure Next the export scene as tab will appear, next the give the nwc file name as project STRUCTURAL

STEP 3:

• The arcitectural and structural model are opened in navisworks

RESULT:

Revit structural and architerual model are successfully exported to the navisworks file.

2) Use Navigate Tool to walk around the model and walk through the rooms created and record your moving as animation in your Navisworks file

AIM-

Using the Navigate Tool to walk around the model and work through the roome created and record moving o animation in your Navisworks file

INTRODUCTION

• With the Walk tool you can navigate through a model as if you were walking through it.
• Once you start the Walk tool the Center Circle icon is displayed near the base of the view and the curio changes to display a series of arrows to walk through the model you drog in the direction in which you want to move in

PROCEDURE

Step:-1

• After opening the architectural view in the navisworks, then click on the walk hook as shown in the below figure
• Next we use the record option in the viewport toolbar to record the moving it each and e room, as shown in the below Figures

STEP 2:

Walkthrough of living room

Step 3:

Walkthrough bedroom

Step 4:

Walkthrough of kitchen

RESULT:

• Used navigation tool to walk around model
• walkthrough in rooms are done
• To record moving as animation in navisworks file.

3) Use Navigate tool to use Realism feature to walk through the model and record your moving as animation in Navisworks file

AIM:-

Use Navigate tool to use Realism feature to walk through the model and record moving as animation in Navisworks file

INTRODUCTION

• This function allows you to navigate scene from a third person perspective
• When third person is activated you will be able to see an avatar which is a sepresentation of yourself within the 30 model
• Whilst navigating you will be controlling the cvator's interaction with the current scre Using third person in connection with collision and grovity makes this a very powerful function allowing you to visualize exactly how a person would interact with the intended design You can customize settings such as avatar selection, dimension, and positioning for the current a global option

PROCEDURE

Step 1:

First we open the realism option and select the third persons as shown below Nat we use the record option in the viewport toolbar to reoped the moving ta onimation in each and every room as shown in the below figure

STEP 2:

Walkthrough of living room

Step 3:

Walkthrough bedroom

Step 4:

Walkthrough of kitchen

Step 5:

Walkthrough of entrance

Step 5:

Walkthrough of staircase

RESULT:

• Used navigation tool to walk around model
• walkthrough in rooms are done
• To record moving as animation in navisworks file.

4) Embed both architecture and structure *.nwc file to your Navisworks file. Create a clash detection test between the two models

a. Run the Clash Detection Test
b. Study the clashes between the two models
c. List which of the clashes could be approved
d. List which of the clashes could be neglected ( will be taken care later)
e. List which of the clashes can be resolved
f. Save the results after color coding the clashes to the Navisworks file
g. In case of resolution annotate the clash and save the view to defined views in Navisworks

AIM:-

To Create a clash detection test between the two models

INTRODUCTION

• The Clash Detective tool enables you to search through your total project model identilyong cross-discipline Interferences (clashes) earlier in the design process This feature is available for Autodesk Navisworks Manage users only

PROCEDURE

Step 1:

First we need to open the home tab and select the cloth detective tool

Step 2

we need to study the clashes between the two models

step -3

• Next list down the clashes which are approved.

• Next list down the clashes which are neglected.

• Next list down the clashes which are resolved.

STEP 4:

• Next save the results after colour coding the clashes.

STEP 5:

Resolved clashes can be clearred from the list by using the compact option.

RESULT

Created a clash detection test between two models successfully.

5) Using the Timeliner feature in Navisworks prepare a schedule for the project developed in week 6 to 8 by adding reasonable assumptions for task start date and end date and simulate the task completion as a visual simulation. Record it and save the timeline simulation to Navisworks file

AIM:

To use the Timeliner feature in Navisworks to prepare a schedule for the project developed in week 6 to 8.

INTRODUCTION:

• The Timeliner tool odds schedule simulation to Autodesk navisworks
• Timalinelimports schedules from a variety of sources
• You can then connect tasks in the schodole with cojects in the model to create a simulation This allows you to so the affects of the schedule on the model and compare planned does against actual
• Costs can also be assigned to as to track the cost of a project throughout itz schedule Timelinoralec allows the sport of imoges and animations based on the results of the simulation
• TimeLinerwill automatically update the simulation if the model or le chunges

PROCEDURE

Step 1:

First we operi the structural modes in rivisores which was opened from revit

Step 2

Next select the home tab and select the timeliner

Step 3:

Next add the tasks and attach the tasks in it

Step 4:

Update the actual dates like start and finish date to the task

Step 5:

then click on the simulate to play the recorded task and save the project

RESULT

The timeliner feature is used successfully in navisworks to prepare a schedule for the project developed in week 6.