All Courses
All Courses
Courses by Software
Courses by Semester
Courses by Domain
Tool-focused Courses
Machine learning
POPULAR COURSES
Success Stories
The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…
Rahul Prajapati
updated on 14 Sep 2022
The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:
The structural model must comply with provisions of IS 1893 and IS 13920.
Run a modal response spectrum analysis and check analysis results of the etabs model for inter-storey drift requirements, vertical & planar irregularities, minimum shear wall requirements,maximum axial load ratio for column and shear walls, effective moment of inertia for beams
and columns etc.
Please note that the column positions shown in the architectural typical floor plan are only to provide an initial starting point for modelling. Participants will have to change its size, introduce shear walls, and add new vertical elements after running the analysis. You will have to run the analysis multiple times until a structural model is obtained that meets structural code requirements without compromising architectural functions. Also, there is no one ‘correct’ structural system for this challenge. There can be multiple possible solutions for this problem.
AIM:
To model an apartment with all seismic consideration, based on given architectural input and to know how to check the seismic performance of an apartment using ETABS
INTRODUCTION:
To model and analyse the G+7 residential building with the given architectural drawing using ETABS
Data required for Etabs analysis-
Conceptual design consideration before analysis-
Key point to remember while modeling-
PROCEDURE:
STEP 1) Create Model Reference in AutoCAD
STEP2) Create New Model in ETABS
STEP3) Create Grids
STEP4) Add Building Storey
STEP5) Define Material
STEP6) Add Column, Beam & Shear Wall
STEP7) Add Slab
STEP8) Load Pattern
STEP9) Define Mass Source
STEP10) Response Spectrum
STEP11) Check Load Case
STEP12) Load Combinations
STEP13) Draw Column and Shear wall
STEP14) Assign Load
STEP 15) Add Diaphragms
STEP 16) Base Support
STEP 16) Assign Peir Lebal
STEP 17) Add live load Reduction factor on each floor
STEP 18) Check Modal and Run The Analysis
STEP 19) Check Result
RESULT:
To model and analyse the apartment with all seismic consideration, based on given architectural input and to check the seismic performance of an apartment using ETABS and attach the modal
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Project 2_Analyze and Design the RC office building as per IS standard code in TEKLA STRUCTURAL DESIGNER
AIM:- To develop general arrangement for the RC office building. Also, to analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER from the attachment. Also, to generate report of each member and extract drawings for structural plans, beam reinforcement details from the software. INTRODUCTION:- Tekla…
12 Jan 2023 04:11 AM IST
To Generate report for Steel Industrial and RC structures using TSD
Generate report for the steel building design from challenges 1 – 6 along with the loading summary Aim: To generate report for the steel building design. Procedure: Open the saved Tekla model Now go to the report option from the Ribbon and select model report. Now select the load cases and combinations summary to obtain…
11 Jan 2023 12:24 PM IST
To Design slab and foundation for an RC residential building using TSD
1.Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations) Aim - To design the slab and foundation of the model. Tools Used - 1st Order analysis, Analysis all ( static ), Status , check panel ,Properties window etc. Procedure - Open the…
10 Jan 2023 06:49 AM IST
To Design RC column and beam for RC residential structure using TSD
Aim:- to run the analysis of the structure and design reinforced concrete beam and column procedure:- open the tekla model and run the analysis now select any of the column member and right click on it then select the interactive design from the given option check whether the member is passing through all the design checks…
10 Jan 2023 04:48 AM IST
Related Courses
Skill-Lync offers industry relevant advanced engineering courses for engineering students by partnering with industry experts.
© 2025 Skill-Lync Inc. All Rights Reserved.