Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code
Aim:Sketch a G+1 floor reidential plan, according to vaastu shastra, and list down the names of the structural drawing required to be provided to be site for construction.
Also assume the sizes of the structural elements (coloumn,beam,slab,etc)and accordingly calculate the indivisual corresponding loads from the members as per IS code.
GROUND FLOOR:
Living room :3.60m.5.85m
Kitchen room :3.60m.3m
Dining room :3m.3m
Master bed room :4.3m.3m
Bed room :3m.4.5m
Toilet :3.25m.1.2m
Bath :2.4m.1m
Water coset :1.2m.1m
FIRST FLOOR PLAN:
Guest room : 4.3m.3m
Bed room :3m.4.5m
Study room :3m.3m
Toilet :3.25m.1.2m
Bath :2.4m.1m
Water coset :1.2m.1m
OTHER DIMENSION:
Thickness of extra wall -0.23m(230mm)
Thickness of internal wall-0.15m(150)
Thickness of slab-0.25m(250)
Dimensions of coloumn_0.3m.0.3m
Dimensions of beam-0.3m-0.45m
Height of the wall of each floor-3m
VASTU SHASTRA FOLLOWED DURING PLANING:
*Entrance of the house is provided in the east direction which is the symbol of progress in life.
*Living room is placed in north east direction.
*Master bedroom is placed in the south west position this posision brings good health and prosperity.
*kitchen is placed in south east direction.
*Study room is placed in east direction.
*Stairecase is placed at north west corner
*Bath room, Wc and toilet is placed in west direction.
CONSTRUCTION PROJECT:
For any construction project ,construction documents,Drawing sketches and planes are nedeed for proper execution of the project.There can beplenty on different document that make up your set.Different clients and building have different requirement.Even the scope of the budgetfor the project can change the drawing requirements of the project.However certain conventions have become conventions have become widely accepted. following are the types of drawing in a typical set of construction Documents.
*Architectural drawings
*Electrical drawings
*plumbing drawings
*Fire fitting Drawings
*HVAC Drawings
1.ARCHITECTURAL DRAWINGS:
An architectural drawings is a technical drawing of a building that is used by architects to develop a desing idea into a coreharent proposal to communicate,ideas and concepts to convience clients of the meritsof a desing,to enable a building contractor to construct it, as a record of the building that already exist.
The following are typically components found in a full set of architectural construction.
DRAWING:
1.Setting out of plan
2.Floor plans
3.Elevation drawing
4.section drawing
5.Working drawings
6.Opening schedules
7.Rood drainage plan
8.Flooring plan
9.Furniture plan
10.typical details
2.ELECTRIFICATION DRAWINGS.
These drawings shows the location of electrical equipment and their layout in the building.
1.Electrical legend
2.Floor lighting plan
3.Floor power plan
4.Single line diagram
5.Fire alarm layout
6.Floor sound system and CCTV Camera
7.Equivalency chart
8.Lightening protection earthing details
3.PUBLIC HEALTH DRAWINGS:
1.Legend and General notes.
2.Sewerage and Rainwater layout plan
3.Manhole schedule
4.plumbing construction details
5.Water supply layout.
4.Structural drawings
These drawings show the support system of the building like how the building is standing what are its stuctural components what is the strength of the building and how beams coloumns stairs slabs etc. are connected and thus like.
1.General notes
2.typical sections.
3..foundation excavation plan
4.footing section
5.Ground floor coloumn plan
6.coloumn sections
7.Ground floor plinth beams plan.
8.Plinth beams sections
9.Ground floor beam plan
10.Beam sections
11.Ground floor slab bottom rebar details
12.Ground floor slab top rebar details
13.Ground floor slab section
14.Overhead water tank desing
15.septic tank desing
FIRE FIGHTING DRAWINGS:
1.Legend and Notes
2.Fire fitting layout plan
HVAC DRAWINGS:
1.Legend and general notes
2.AC layout plan
3.equipment schedule and installation details
Results:
1.The plan is prepared by the vaasthu shastra concept considerations of vaasthu shastra
2.The load calculation are done as per the IS code consideration