Roof challenge

 What is industrial designQuestion-1 :To Develop- Industrial design sketches- Concept & technology that will be usedTo design a mechanism that can automatically move along vertical Y-axis [ Height ] for anoutdoor kiosk with a display.[The product design for this assignment should also house a display & this…

AIM - To create the Door trim panel's CAD model considering the inputs given to me following the design rules and OEM standards. ABSTRACT - The project deals with the explanation of steps and procedures followed while developing the Door Trim Panel of a car using CATIA V5. Using the class A surface I was…

WIRING HARNESS FOR ENGINE AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known as a wire…

WIRING HARNESS FOR ENGINE AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known as a wire…

WIRING HARNESS FOR ENGINE AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known as…

  WIRING HARNESS FOR TAILGATE   AIM: To route the wiring harness for the given Tailgate. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known…

                                                    Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM- To prepare a flattened-view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened-view for a harness assembly and then place it on the drawing sheet.…

                                                 Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge DESIGN OF WIRING HARNESS ROUTING IN CATIA V5 INTRODUCTION The wiring harness…

                                           Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge Objective: To Route the harness layout in Electrical workbench based on the given input.To add protective…

                                                  Wiring harness routing & packaging Rules Week 3 Challenge AIM: To solve the above assignment questions and define the necessary electrical properties in the respective workbench.   OBJECTIVE:   To download the P-Clamp CAD data and define it as Electrical Support in the…

                                                    Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge   INTRODUCTION Wiring harness is the combination of electrical and mechanical…

AIM: Create the part models and assembly for the given drawings below with a report. DRAWING 1 (QUICK RETURN MECHANISM): REPORT ANALYSIS:Intially created the part of the drawing in the part workbench. Sketches and CAD Part: After creating all the parts go to the Assembly Workbench and insert every part to the assembly…

                      Challenge 4 - Bumper Objective: The main objective of this challenge is to create a solid body of 'Bumper' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis'…

 A pillar Design with Master Section Master Section: Master sections are the guides for design requirements which decide the component packaging after technical (Styling, Concept or Class-A) surfaces. Overview: Here in this challenge, I created the solid part body from the class A surface and B-side features (Dog house)…

Door Trim Lower with Engineering Features     DOOR TRIM LOWER Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. •…

Attachment Feature Creation AIM: To create the Screw boss and Dog House for the Centre console coin holder by considering the design rules.  OBJECTIVE: General Guidelines for Bosses:   Draft  - 0.5 degrees on walls of boss   Thickness -  Typically 40%* of the nominal wall at the…

Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1 Aim        1. To create the Door Handle  Component from the given Class A surface      2. To Create the the tooling axis for the given Class A surface meeting the requirement of Draft angle.      3.…

 Core & Cavity Design Aim:-To create Core & Cavity block for switch Bezel. Draft analysis:- Draft analysis is required to check if a part has required draft or not. The draft analysis refers to a Tool that allows us to deteermine if we can remove the part we are designing.Here I used Analysis option, change…

                                                                   Week 8 - Challenge 3 - Coin Holder Design   Objective : To design coin holder…

                                                               Week 8 - Challenge 2 - Switch Bezel Design Objective         The objective…

Week 8 - Challenge 1 - Base Bracket Design OBJECTIVE To create base bracket plastic component from the given class- A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. CLASS- A SURAFCE THIS WAS THE GIVEN SURFACE  class - B surface A Class B surface…

                                                                          Back door challenge   1. Objective: To design…

                                                                          ROOF CHALLENGE Aim- To develop the essential flanges…

                                                               SECTION MODULUS CALCULATION Aim :- To calculate the section modulus of the previously designed…

                                                                       WHEEL ARCH CHALLENGE OBJECTIVE: The objective of the wheel arch challenge…

                                                                                           …

HOOD - Its is an opening body panel that covers the engine in a front engine vehicles & hood can also allow access to the engine compartment , or trunk on rear engine  & some mid engine vehicle for maintainance & repaier, its also known as Bonnet In hood panel there are two panels :- INNER PANEL -…

I've already written my answer on white paper and attach the file.

UNDERBODY COATING Underbodycoating is a process which covers the internal surface from corrosion for very long time.It also protects parts like internal body panels or It was a sprayable or painted process. Its advantages are :-    Minimizes sounds           : Minimizes sounds…