Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. AIM: To Exporting the Revit architecture and structure model to the Navisworks Cache file as discussed in…

                        Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo 1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM:To create a set…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School                 - I want to build Office Building from…

                                       3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using Revit  Tools Used:    …

Project 2 :- Creating a 3D rendered model for a Residential Building in AutoCad AIM: To create the 3D rendered model for a Residential building in AutoCad. Introduction :- 3D CAD, or three-dimensional computer-aided design, is a technology for design and technical documentation, which replaces manual drafting with an automated…

1. Aim :- To Create a 3D Isometric View of the building with plan and elevation given.     Procedure :- Click on AutoCAD application and open this application Type QNEW in command bar and enter Select default setting as Imperial In default setting click on use a wizard and in that advance setting and set unit as Engineering…

1. Aim: To draw the 3D wireframe model as shown in the figure. Introduction: The 3Dwireframe model given is a furniture equipment in the house. The 3d wireframe model is drawn in different coordinate systems such as rectangular coordinate system, spherical coordinate system, relative coordinate system and cylindrical…

Aim: To create layout of the Plan and Section A of the project in Challenge 7 as shown in the figure above, in AutoCAD. Introduction: The layout is created in AutoCAD using the template Tutorial-mArch.dwt in a scale 1:50 that given in the Figure. The procedure is explained in detail with diagrams…

1.PROBLEM 1 Aim :- To create the kitchen layout and to provide the hatch. Introduction :- The general commands used for drawing the building is as follows : 1. Line 2. Polygon 3. Rectangle 4. Circle 5. Erase 6. Copy 7. Trim 8. Mirror 9. Offset 10. Extend 11. Array 12. Move 13. Rotate 14. Dimension 15. Text…

Aim: To create templates and convert as shown in the figure using AutoCAD. Procedure: STEP:-1 In the command prompt type UNITS and press enter. Select the required units as desimal and select the required insertion scale. Select layer settings from ribbon tab. From the layer settings tab select create layer option. Enter…

Aim :- To Design and Draft a layout of a Residential Building having plot size of 60' X 20' ( 18.3m X 6m ), facing East-direction using AutoCAD.   Section 1 :- Architectural Drawing Site Plan Layout Ground Floor Plan First Floor Plan Elevation Section View Section 2:- Structural Drawing :- Column Layout Plan…

AIM: The project's goal is to use the Etabs programme to model and analyse a G+3 building with the provided seismic details. Building Foundation employing Safe software for the outcomes of the Etabs analysis column reactions. AUTOCAD is used to create detailed drawings for the structural plan, the reinforcing details for…

QUESTION-1 Introduction: According to the isolated footing in the week 11 challenge, the foundation was designed, analysed, and calculated in order to arrive at the steel reinforcement. Procedure: Create new model>input the metric units > is code usage IS 456-200 Step:1   Step:2   Choose single footing…

Introduction: This challenge asks participants to manually compute the shallow foundation reinforcement details in relation to the design limit state. Calculation of Total soil pressure / Gross soil pressure: Total unfactored Load=2000/1.5=1333kN Assume thickness of footing (t)=500mm=0.5m Given Height of footing=2m  Pressure…

Aim: The objective of the challenge is to create the best structural feasible plan for the given architectural plan. And to model the framing plan in ETabs for G+7 building. Forming of schematic framing plan : Step:1 For the provided architecture drawing, the alignment of the walls and columns are set up using reference…

Introduction: The challenge's goal is to create a shear wall utilising the analysis and findings from the accompanying ETabs model of a G+6 building. And to generate a comprehensive sketch of the RCC Shear wall at GL-A/11, 300 x 1500 mm in size, using the model's derived reinforcing information. RCC Shear wall designing…

Introduction:   The challenge's goal is to analyse and design a column for the given G+4 building etabs model using IS 13920-2016 as a guide. And to develop the design's resulting details for the building's column (3A&3B) lapping details, longitudinal reinforcement, and shear reinforcement. Additionally, comprehensive…

Aim:The project's goal is to analyse the provided work and extract the details drawings for the specified beams in 2 grid lines that are both vertical and horizontal.Additionally, to examine and redesign the faulty RC Beam Analyse and Design of RC Beam: Step:1-Model Check Analyze > Check Model Analyze > Run Model…

AIM: Objective of the project is to model and comparison of result between the models (A-K). And to investigate the models based on the time period in modal behaviour for various effects given below, Effect of stiffness on Time period. Effect of mass on Time period. Effect of Building height on Time period. Effect of column…

AIM: Objective of the project is to model & analysis of 25 storey building using Etabs for the given specification and to verify the results as per the IS 1893 codal provision.   Procedure: Step:1   EditDropDown (tool bar)> Modify/Show Story Data... (button)> Modify/Show Grid System... (button) Using…

Answer for Question-1: Criteria       Restraint of Floor shrinkage Since all four corners of floor is restricted to experience shortening, this RC wall system possess good control of shrinkage. The edges of Floor are restricted to floor shortening. Whereas the corners are prone to shortening/shrinkage with…

Question:1     Observation of framing plan in X-Dir: With respect to Symmetry: When we divide the framing plan vertically, both sides will look symmetrical with respect to y-axis.   With respect to redundancy: Columns are spaced closer and even. More redundant in X-Dir. Except the 1st and last column…

The answers are attached.

The answers has been atached 

1.a)  Type of issue : Repairable Damage  Observation: The concrete parts are fractured at the beam bottom at a Column Beam connection. No significant problems appeared to be emerging in the Column zone. It appears that the reinforcements are unharmed. Reasoning: It's possible that at Support, the beam's compressive…