Drafting of various geometries using Chamfer, Fillet tool in AutoCad

AIM:To draw the drawing in decimal units by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• To draw the drawing in decimal we select the units as decimal millimeters.
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the drawing in architectural units by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the dimensions are given by using dime command .
• To draw the drawing in architetural we select the units as architetural inches.
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. dime command

AIM:To draw the drawing in engineerig units by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• To draw the drawing in engineering we select the units as engineering inches.
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.
• To give radius to the use the circle center and circle in circle down.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.
• To give radius to the use the circle center and circle in circle down.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. circle command
3. dime command

AIM:To draw the given drawing by using autocad.

PROCEDURE:

• First selcet the units and limits as per the drawing requirements.
• In above drawing all the lines are drawn by using the line command in below command section.
• All the circles are drawn by using circle command by giving required radius of circle.
• All the dimensions are given by using dime command .
• Also the lines with angles by using @dist<angle.

COMMANDS USED IN THE ABOVE DRAWING ARE :

1. line command
2. dime command