Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad

Aim:-to create kitchen layout and also use proper dimension techniques to dimension the layout

INTRODUCTION:- Kitchen layout is the most important part of designing your perfect kitchen .Its the layout that will determine how you cook,how you eat and how you socialise

Command used:-

• LIMITS COMMAND
  LINE COMMAND
• OFFSET COMMAND
  
• HATch command
• DImlinear
• UNJTS
  
• Extend
• FIllet
• object snap

PROcedure:-

• Units are set to mm
• Limits and limmax are also set up
• Zoom command is also used
• tye rec and dimenions are 4734*3688mm
• Type offset and offset it to distnce of 250mm
• Using arc and lijnes door is drawn
• In the command prompt type hatchg to hatch the model
• Specify the centere as 10,10 and radius 452
• Offset from top of dimensions 12 and 488 mm
• In the command line type offset
• Create the offset from the side at the distance of 608.75 and 365
• In the command line type L and by increasing the transparency to create wall surface
• By using hatch and give scale 20
• In the command line type q leader to mention the annot
• Create the offset from the side at the distance of 608.75 and 365
• Offset from top of dimensions 12 and 488 mm
• In the command line type offset
• Create the offset from the side at the distance of 608.75 and 365
• IN the command prompt offset it to horizontal distance of 350,450,900,450,450,560
• Now offset it to vertical distance of 600mm
• Place all the required elements in respected layers.

RESULT:-

AIM:-TO create the elevation of the plan created in the challenge 7

INtroduction:-ELEVATIOn drawing are a specific type of drawing architects use to illustrate a building or portion of building . an elevation is drawn from avertical plane looking straight into building or portion of building.

COMMANDS USED:-

• LIMITS COMMAND`
• OFFSET COMMAND
  
• HATch command
• DImlinear
• UNJTS
  
• Extend
• FIllet
• object snap
• OFFSET COMMAND
  
• HATch command
• DImlinear
• UNiTS
  
• Extend

PROCEDURE:-

• OPEN THE AUTO CAD AND SET THE LIMITS
  
• ZOOM COMMAND AND PRESS enter
• Comming to the drawing the elevation of residential building first we draw the horizontal line using line command with the length of 11574mm
• NExt we need to draw the another line frrom the previous line vertically with length of 1200mm
• NExt we have to draw the line horizontally towards from previous line with the length of 12150mm at the top
• NExt we draw a rectangle at the top of building
• next we draw the the three rectangle at the bottom of recctangle with dimension

STEP-2

• NExt we need to draw the sunshades provided in the drawing
• Next we draw the windows with standard construction dimensions with the help of line command
• Next draw the balcony part using the line command ,offset command and trim command
• Next we draw the remaining architectural elements using line command rectangle comamd and offset command

STEP-3

• We use the hatch command to hatch the walls ,door windows and other architectural elements

RESULT:-

AIM:- TO create a section view of an industrial building and need to provide appropriate hatches and dimensions where ever required.

INtroduction:-

• In reference to architectural building ,the term section typically describes a cut through the body of a building ,perpendicular to the horizon line , asection drawing is one that shows a vertical cut transpecting typically along the proimary axis an object or building.
• A section diagram is a view of the building that slices through the building to better see the specific aspect of the building better
• This drawing is particulary interseting because it cuts through

Commands used:-

• LIMITS COMMAND`
• OFFSET COMMAND
  
• HATch command
• DImlinear
• UNJTS
  
• Extend
• FIllet
• object snap
• OFFSET COMMAND
  
• HATch command
• DImlinear
• UNiTS
  
• Extend

Step-1:-

• first we have to draw the x- line at annoy point on the screen
• next offset the line to top a distance of 5850 mm and we have to do offset of last offset line to the distance of 300mm
• Comming to the drawing the elevation of residential building first we draw the horizontal line using line command with the length of 11574mm
• NExt we need to draw the another line frrom the previous line vertically with length of 1200mm
• NExt we have to draw the line horizontally towards from previous line with the length of 12150mm at the top
• NExt we need to draw the sunshades provided in the drawing
• Next we draw the windows with standard construction dimensions with the help of line command
• Next draw the balcony part using the line command ,offset command and trim command
• Next we draw the remaining architectural elements using line command rectangle comamd and offset comm

STEP-2:-

• NExt we need to draw the sunshades provided in the drawing
• Next we draw the windows with standard construction dimensions with the help of line command
• Next draw the balcony part using the line command ,offset command and trim command
• Next we draw the remaining architectural elements using line command rectangle comamd and offset comm

STEp-3:-

• NExt we need to draw the another line frrom the previous line vertically with length of 1200mm
• NExt we have to draw the line horizontally towards from previous line with the length of 12150mm at the top
• NExt we draw a rectangle at the top of buildingds

:-

• PRovide hatching wherever required
• provide layers
• layers of dimensions and text are provided

STEP-5:- The sectional view of building of the industrial building is drawn successfully in the autocad in detail.

RESULT:-