Creating Architectural and Structural model with 3D rendering using REVIT

AIM:       To provide details of longitudinal reinforcement for the two columns, from foundation to terrace level and to show shear reinforcement & lapping details as per special confining reinforcement provision of clause 8.1 of IS 13920 - 2016. PROCEDURE:        - Open an Etab…

Aim:       To provide details of longitudinal and shear reinforcement for the given two continuous beams and to calculate the value of maximum shear force in any one of the spans in the continuous beams. PROCEDURE:        - We must go to Challenge 7 and download…

AIM: To model a 25 storey building with the specified properties using etabs. PROCEDURE:          - Open the etabs software.          - From the file menu choose to create a new model option.          - After choosing a new model…

1. The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the…

1. Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.                      …

1. A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. A.)                   …

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures. A.) STATIC ANALYSIS:               - Load is not variable with time and neglected due to the delayed application of load.               -  Motion…

1. What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate. A.)     (a).             OBSERVATIONS:                      From the picture, we can see that the…

1. Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. A.) AIM:         To export the Revit architecture and structure model to Navisworks Cache…

1. Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School A.) The type of structure I want to build from one of the three below is      …

1.  Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. A.) AIM:          To create a set of sinusoidal points and create a curve and create a surface out of the curve using dynamo.       PROCEDURE:             - Open the revit software.             - Select Architectural…

1. Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. A.) AIM:           To model a ceiling from the architecture tab above the walls at the first-floor level.      …

AIM:    To create a 3D rendered model for a Residential Building in AutoCad. PROCEDURE:     - Open AutoCad.     - Select 3d modelling and enter units command and choose decimal.     - Select line command and draw in top face.     - After drawing remove the unwanted lines.     - Offset a distance of 230 for wall.     -…

1.) AIM: To create a 3D Isometric View of the building with plan and elevation given.      PROCEDURE:              - Open autocad and the set the maximum and minimum limit.              - Draw a rectangle using the rectangle command according…

1.) AIM: To create a 3D Furniture element as shown in the Figure.      PROCEDURE:              - Open AutoCad and choose engineering with units as inches.              - Create a box with box command, give length as 3' and width as 2'6".…

1.) AIM: To create a layout of the Plan and Section A of the project.      PROCEDURE:              -  Open AutoCad and in the command prompt type units > mm> decimal, then type limax >100,100 and finally type limits>0,0.        …

1. AIM: To create the layouts of the Kitchen and provide hatches pattern.     PROCEDURE:             - Open AutoCad and type UN in the command box. Choose decimal option.            - Use the line command to create a line that is 4300 in the X direction and 3200 in the Y direction and finish the rectangle.            -…

1. AIM: To create the templates as shown in Figures.      PROCEDURE:            - Use line command by typing L.            - Draw the schedule as per the illustration.            - Type the texts as indicated…

AIM:     To Design and Draft a layout of a residential building with plot size (18.3 m x 6 m). PROCEDURE: - Type Units in the command and then click Meters. - Type zoom > a in the command prompt. - In the command prompt type offset, to offset it to the desired lines. - In the command promt type trim…

1.) AIM: To create the plan and sections as shown in the figures.      PROCEDURE:               - The units of the drawing sheet is set to Engineering precision.               - Construction lines are drawn both horizontally…

1.) AIM: To draw the elevation and details of a wardrobe as shown in the figure above.      PROCEDURE:               - Both horizontal and vertical lines are used to draw the wardrobe's layout. As shown in figure, the doors of these cabinets are drawn with the…

2.) AIM: To create a window schedule.      PROCEDURE:             - Open a new AutoCad file with imperial system.             - Select architectural and give precision 0'0 1/256"             - Now, use command "TABLE"…

1.) AIM: To Sketch the layout of a residence as shown in the Figure 1.      PROCEDURE:              - The various commands used are: units, line, rectangle, fillet, copy, offset, dimension, layers, explode.              - The units…

The various commands used in this challenge are: Line Circle Rectangle Copy Offset Trim Polygon Point Rotate Fillet 1.) AIM : To draw the given figure using AutoCAD: A.) PROCEDURE: Step 1: Drawing outer box Type line in command box or select line from the draw tool bar Specify first point: Type (1,1) and…

1.) C.S. OF LOAD BEARING WALL OVER SPREAD FOOTING: A.)                      2.) C.S. ISOLATED FOOTING: A.)                     3.) LINE DIAGRAM OF A TWO BEDROOM BUILDING: A.)         …

1.) AIM:         To create the geometries from P1 to P2 using all the coordinates system methods and to use the Line tool to create the geometries.  P-1.)       PROCEDURE:        a) Absolute Coordinate System: 1. Select the line tool by entering the 'Line'…

Q.) Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from…

 1.) Aim : To calculate the Concrete Mix Design for M35 grade concrete with fly ash.       Procedure:       Step : 1 - Stipulations for proportioning       a. Grade designation : M35       b. Type of cement : OPC 43 grade conforming to IS 8112  …