Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad

AIM:

To draw the elevation & details of a wardrobe as shown in the figure below.After sketching & to provide the dimensions & text with the use of layers.

PROCEDURES:

DWG-1

0.1

• Units are set in mm, Limits are set.
• Taking Rectangle in command line as (2800,2600).
• In the command line type offset.
• offset from the top of dimension 12 & 488mm.
• In the command line type offset.
• Create the offset from the side at the distance of 608.5 & 365.
• create the offset from the bottom of dimension 100 & from 100 take 900 offset.
• by using hatch give the hatch & transprency in hatching setting & give scale 20.
• in the command line type Qleader to mention the annotations.
• Give the dimensions & Labeling.         

0.2

• In the command prompt type Rectangle 630*2800
• Take offset from side 2435mm.
• in the command line type Qleader to mention the annotations.
• Give the dimensions & Labeling.       

0.3

• In the command line Rectangle 2800*2600
• with the help of command drawers & cabinets are created.
• For the drawers & cabnet give the grey colour.
• Take offset from side 12,1223,1200.365
• Take offset from bottom 900.
• Dimension the drawing.

0.4

• In the command line Rectangle 520*630,1180*630,900*630,900*630 This is repeated 2 times
• Using line commands,the next of the lines are drawn.
• Dimension the drawing.
• Place the entire drawing in the respective layer.

DWG-2

AIM:

To draw the given floor plan.

PROCEDURE:

• Units are set in mm.
• Limits are set.
• In the command line type XL to draw the infinite lines.
• In the Command prompt type offset to offset the line for a particular diastance.
• Using arc command doors are also created. 

Doors & Ventilators: 

01 D1= 1000*2000mm

    V1=800*500mm

02 D2=900*2100mm

     V2=750*500mm

03 D3=800*2100mm

04 D4=750*2100mm

05 D5=700*2100mm

06 SD=2256*2100mm

Windows:

W1=2700*1500mm

W2= 2500*1500mm

W3=900*1500mm

W5=1000*1500mm

W9=800*1500mm

To draw canopy

CIRCLE:

• In the menu bar click on circle.centre,radius.
• Specify the centre point as 10,10 & radius 452.
• In the menu bar click on circle > centre,radius.
• Specify the centre point same as the previous circle (10,10) & radius 1398

SEATS:

• In the menu bar click on rectangular,specify the length of the rectangle as 662.3.
• Specify the width of the rectangle 298.0
• In the command prompt type Filllet >radius>100 
• Take circle.2 points 
• Take circle>centre>diameter
• Centre is the midpoint of the line,diameter is 719
• Take circle>centre>diameter
• Centre is the midpoint of the line,diameter is 777.2
• Now, Extends the centre line & trim the extar's
• In the menu bar click fillet>blend curves>& select the arc.
• In the Menu bar click Fillet >Blend curves>& select the arc.
• In the menu bar click Fillet>Blend curves> & select the arc.
• Give the dimensions as per given in drawing & annotation with the text where ever required.
• Place the all elements of the in the respective layers.

DWG-3

AIM:

To create the kitchen layout & to Also,Use proper dimension techniques to dimension the kitchen layout.

PROCEDURE:

• Units are set in mm, Limits are set.
• In the command prompt type rec & the dimension  are 4734 & 3688mm
• Take offset it to the distance of 250mm.
• Using arc lines the door is drawn.
• In the command prompt type hatch to hatch the model.
• In the command prompt type rec>dimension ,to do the fridge
• Take offset it to the desired distance to get the micro oven.
• Take trim to trim  the extras.
• Offset it to the horizantal distance of 350,450,900,450 & 560.
• Offset  & Offset it to the vertical distance of 600
• In Type trim command & trim  the extras.
• In the command type line type & load the dotted lines.
• In the command type text to text the given annotations.
• Given the dimension as per the plan.
• In the command prompt even the leader command is used to name the dimension.
• Place the all elements of the in the respective layers. 

DWG-4

AIM: To sketch the column details.

PROCEDURE:

• Units are set in mm & Limits are set.
• Using rectangle & line command line tables are drawn.
• Using text command,the text is given.
• In the command type lines to draw the reinforcement.
• Type circles to draw the reinforcement.
• Give the dimensions as per given in drawing & annotation with the text where ever required.

DWG-5

AIM:

To draw the raft layout.

PROCEDURE:

• Units are set to engineering>inches & Limits are set
• In the command type Rectangle>dimensions are 29'-7" & 60'
• To get dotted lines click on line type & load the dotted lines >set current.
• with the help of dotted lines & offset command the grids are drawn.
• In the command offset the distance to 4"
• In the Ribbon >hatch>AR-CON
• In the command type rec 2'*2'
• Take rectangle to draft the columns.
• In the ribbon bar select hatch>ANSI37 hatch the columns
• In the ribbon bar select hatch>ANSI33 hatch the columns
• Take the Annotate>Text the given annotations.
• Given the dimension as per the plan.
• Place the all elements of the in the respective layers.