Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad

1) RESIDENCE PLAN

AIM: TO DRAFT THE LAYOUT OF RESIDENCE PLAN AS SHOWN IN FIGURE1 USING AUTO CAD SOFTWARE.

INTRODUCTION : THE GIVEN RESIDENCE PLAN CONTAINS 2 BED ROOMS WHICH CONTAINS ATTACHED TOILETSTOGETHER WITH DINING ANG LIVING HALL COMBINED TOGETHER WITH CONNECTED KITCHEN.

PROCEDURE :

• GO TO START MENU,SELECT INSTALLED AUTO CAD VERSION LIKE 2023.
• CLICK ON START DRAWING.
• GO TO CREATE NEW DRAWING.
• THEN NEW TAB WILL OPEN AND IT SHOWS FOUR ICONS.
• USE THE DEFAULT IMPERIAL (FEET AND INCHES) SETTINGS
• OPEN THE TEMPLATE AS ACAD.DWT
• THEN NEW DRAWING TEMPLATE IS CREATED AND SET THE LIMITS AND PRESS ENTER.
• THEN WRITE ZOOMIN IN COMMAND LINE AND PRESS ENTER,TEMPLATE IS CREATED .
• USING UNITS IN COMMAND TAB,SELECT THE UNITS YOU ARE GOING TO DRAFT.
• WRITE LINE IN COMMAND TAB AND PRESS ENTER.
• PUT THE CURSOR ON SCREEN,ENTER THE MAGNITUDE ,SUPPOSE IN GIVEN QUESTION IT IS 43'6.5" AND PRESS ENTER.
• PUT THE CURSOR ON PREVIOUS POINT AND ENTER THE MAGNITUDE SUPPOSE IT IS 25' AND PRESS ENTER.
• USING OFFSET COMMAND DRAFT THE LINE BY WALL THICKNESS GIVEN AS 9" FOR OUTSIDE WALLS.
• CREATING ROOMS BY OFFSET COMMAND,DRAFT THE HORIZONTAL LINE BY ENTERING 12' AND PRESS ENTER.
• MOVING VERTICAL LINE BY 11'7.5" BY OFFSET COMMAND .
• BY USING TRIM COMMAND TRIM THE LINES WHICH ARE NOT NECESSARY.
• THUS TWO BED ROOMS ARE CREATED OF EACH SIZE 11'7.5" * 12'0".
• USING THE ABOVE PROCEADURE, ACCORDING TO ROOM SIZES WE CREATE THE ROOMS BY USING OFFSET COMMAND.
• WE HAVE TO PUT THE DOOR IN GIVEN POSITION USING BLOCK DEFINITION COMMAND.
• FIRST CRATE THE DOOR USING LINE AND CIRCLE COMMAND.
• INSERT IN THE GIVEN POSITION ACCORDINGLY.
• SPECIAL COLOURS ARE DONE FOR DOOR LINES USING LAYER PROPERTIES ON RIBBON AND CORRECT IT FOR COLOUR AS PER STANDARDS.
• AFTER CREATION OF LAYOUT PLAN,WE HAVE TO WRITE THE DESCRIPTION USING TEXT COMMAND .
• DRAFT THE LINEAR MEASUREMENTS ACCORDINGLY USING DIMLIN COMMAND.

RESULT: BY USING ABOVE PROCEDURE,THE LAYOUT OF RESIDENCE PLAN IS CREATED.

2) SEATING PLAN FOR OUTDOOR CANOPY

AIM: TO DRAFT THE SEATING PLAN FOR OUTDOOR CANOPY.

INTRODUCTION: THIS SEATING PLAN CONTAINS ROUND TABLE AROUND WHICH FOUR SEATING CHAIRS ARE PLACED.

PROCEDURE:

• GO TO START MENU,SELECT INSTALLED AUTO CAD VERSION LIKE 2023.
• CLICK ON START DRAWING.
• GO TO CREATE NEW DRAWING.
• THEN NEW TAB WILL OPEN AND IT SHOWS FOUR ICONS.
• USE THE DEFAULT IMPERIAL (FEET AND INCHES) SETTINGS
• OPEN THE TEMPLATE AS ACAD.DWT
• THEN NEW DRAWING TEMPLATE IS CREATED AND SET THE LIMITS AND PRESS ENTER.
• THEN WRITE ZOOMIN IN COMMAND LINE AND PRESS ENTER,TEMPLATE IS CREATED .
• USING UNITS IN COMMAND TAB,SELECT THE UNITS YOU ARE GOING TO DRAFT.
• USING CIRCLE COMMAND DRAW THE CIRCLE OF RADIUS 1398MM UNITS.
• USING SAME SAME COMMAND WITH COMMON CENTRE DSRAW THE CIRCLE OF 452MM UN ITS AND PRESS ENTER.
• USING LINE COMMAND DRAW THE LINE OF 500MM UNITS AND PRESS ENTER AND USING OFFSET COMMAND DRAW THE PARALLEL LINE BY ENTERING 500MM AND PRESS ENTER.
• JOIN TWO EXTERNAL POINTS BY ENTERING CIRCLE COMMAND CHOSING 2POINT METHOD AND PRESS ENTER.
• THUS CHAIR IS CREATED.
• INSERT THE CHAIR IN AROUND CIRCULAT TABLE BY USING CRATE AND INSERT COMMAND.

RESULT :BY USING ABOVE PROCEDURE THE SEATING PLAN IS CREATED.