To calculate the Speed of the sound, Shock wave propagation and 3D meshing of tetra and hexa mesh in Radioss Profile
OBJECTIVE:
1. Check the material properties of the rail component and calculate the speed of sound in steel rail using the given 000.rad file
2. The length of the rail is about 1000 mm.calculate the time takes for a shock wave to travel from one end of the rail to the other.
3.Time for sound to travel the length of the rail
4.Edit the engine file so that the stress wave can be monitored, moving from one end of the rail to the other during an impact -this will require a termination time equal to the time it takes for the sound to travel the length of the rail(set on/RUN card)
5.Set the frequency of animation output to a time that will give 20 animation steps(/ANIM/DT)
6.Change /print -10.
7.3d meshing tetra mesh and hex mesh
- Repeat class examples and, maintain quality.
- Target tet size=5mm,hex size=10mm,tet collapse=0.15.
PROCEDURE:
1. From the given rad file,
Young's modulus of the material E=210 GPa
Density of the material = 0.0078 g/mm*3
The speed of sound is given by the formula below:
C=√E/ρ
Speed of sound = 5188.745 m/s
2. Length of rail = 1000 mm
Time taken for the shockwave to propagate = Length of rail/Speed of sound= 1000/5188.745
Time taken for the shockwave to propagate = 0.1927248 ms
3. Time for sound to travel the length of rail = 0.1927248 ms
5. Frequency = Time taken for propagation/Time steps = 01927248 /20 = 0.009636 ms.
4,6. Editing the Engine Input file.

7. 3D Meshing Tetra Mesh and Hex Mesh.
1d element
8. Open the given model using Hypermesh.
9. Hide all the components except the unmeshed surface and then press F12, select the surface and mesh.
10. 1D < connectors < use any connectors to connect those elements

Hexa Mesh
11. Open the given model using Hypermesh.
12. Hide all the components except the base component.
13. Go to 2D > Automesh > element size: 10mm > element type: quads > select upper surface > mesh.

14. 3D > Line Drag > Select elements > Line along which elements has to be dragged to get 3D solids > Give Density > Drag.
15. Hide all the surfaces and except the arm, the curve makes this as a current component in the component view tab.
16. Spin option for arm bracket, the center of spin must be defined. Go to nodes > Arc centre > select the curve > Create.
17. 3D > spin > Select the following elements shown below > Angle 90 degrees give desired density > Mesh.
18. Hide all the surfaces and wireframes except arm straight make this as a current component.
19. On the outside surface and 2D mesh the surface by matching the exact number of elements at the end of the arm curve.
20. 3D > linear solid > select elements on either side > mention the density > mesh.
22. Hide all the surfaces and wireframes except the boss make this as a current component in components.
23. 2D > Automesh > select top surface of boss > element size: 10mm > match the element as that of arm straight > mesh. Now project the lowermost node of the arm straight to the bottom surface of the boss.
24. 3D > solid map > general > source geom:Surf < elems to drag:elems < dest geom: none < along geom: mixed < elem size = 10 < intensity=0 < Mesh.
25. After doing mesh in all regions delete all the 2D elements in the geometry.

Tetra Mesh
26. Open the given model using Hypermesh.
27. Hide all the surfaces and wireframes except for and make it as a current component.
28. 2D > automesh > element size: 5mm > element type: trias > select the surface > mesh.
29. 3D > Tetramesh < Tetramesh parameters < elem quality target: tet collapse = 0.15 < select component < Tetra mesh < select comps < Mesh.
30. Press F10 < 3D < tet collapse < check the failure elements . And rectify those failure elements by going to 3D remesh options.

RESULTS AND CONCLUSION:
Therefore, the speed of sound is calculated from the formula. The data are obtained from the starter file. Time is taken for the shockwave to propagate and the frequency of animation is calculated.
Time is taken by shockwave to travel: 0.1927248 ms
Frequency of animation: 0.009636 ms
Also, the given geometries have 3D meshed in accordance with the quality criteria given.