Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II

Projec Title : DEVELOPMENT OF A DOOR TRIM PANEL OBJECTIVE : The Objective of the project is to development of vehicle interior door trim panel by using CATIA V5 With given class-A surface along with the master seection. Also Create the side attachment feature as per design rules. INTRODUCTION : The door panel is the interface…

Project Tiltle : ASSEMBLY WORKBENCH 1) Quick Return Mechanism : Part modeling :- Body-1            Body-2               Body-3                   Body-4              Body-5  …

 Project Title : MASTER DEVELOPMENT  Obejctive : To ensure proper tree structure is followed. Creating a tooling axis and following design rules. Creating Class B and Class C surface using Class A surface as an input. Following the master section to create flange. Following the master section for thickness and to create…

Project Title : DESIGN APPLIQUE DESIGN WITH ENGINEERING FEATURES. Objective : To create a door applique and door attachment from the given class-A surfaces and to create engineering features to fit the component in the main surface. Introduction : Engineering feature are the extensions on the plastic components available…

Project Title : ATTACHMENT FEATURE CREATION  Challenge-2 AIM : Create the boss and dog house for the center console coin holder considering the design rules OBJECTIVE : Draft = 0.5 degrees on Walls of boss Thickness - Typically 40% of the nominal wall at the base Height to Diameter Ratio - 3:1 Radii - 0.25mm maximum radii.…

Project Tiltle : ATTACHMENT FEATURE CREATION AIM : To create rib for the center console coin holder considering the design rules. PROCEDURE : Firstly open the coin holder using the open command Rib :- To create a rib first extract the base surface of the coin holder. Create a positioning sketch draw a line, constraint…

Project Title : DOOR ARM DESIGN OBLECTIVE : This report demonstrates the design of a Door Arm Rest an Automotive Plastic Components using industry principals such as Draft angles, Draft Analysis, Determining and implementing of tooling Axis, Class A, Class B, Class C surfaces and maintaining the thickness of the part at…

 Project Title : COIN HOLDER DESIGN Objective : To ensure proper tree structure is followed. Geometrical sets should have a proper name basedd on the sketches present inside of it. All the sketches should be created under the geometrical set. Use of the close surface features to make a solid body from the surface.…

Project Title : CORE AND CAVITY DESIGN OBJECTIVE :  The main objective of the project is to design the core and cavity for switch bazel plastic component Through the give class-A surface and at the end performing the draft analysis on the model. TOOLING AXIS CREATION : The tooling axis is the direction of drawing a sheet…

Project Title : SWITCH BEZEL DESIGN AIM :  To create the switch bezel plastic component through the given class - A – surface and at the end performing the draft analysis on the model. OBJECTIVE : To ensure proper tree structure is followed. Geometrical sets should have a proper name based on the sketch present inside…

Project Title : BASE BRACKET DESIGN   OBJECTIVE : Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Tooling Axis…

Project Title : DRAFT ANALYSIS OF A FAN COVER OBJECTIVE :       The main objective of this challenge is to perform draft analysis on a fan cover by using CATIA V5R21 software which is given in the challenge. A report has to be prepared by explaining about what draft analysis and tooling axis and all the relevant images…

PROJECT TITLE : DESIGN OF CAR BACKDOOR. OBJECTIVE : The main objective of the project is by using the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses. INTRODUCTION :     The trunk or luggage compartment is…

Project Title : CAR ROOF DESIGN. Objective : For the given car roof styling design and develop the essential flanges and reinforcements, namely the Ditch area, Front Roof Rail, Rear Roof Rail, Centre Roof Rail and Bow-Roofs Do a curvature study on the roof and perform calculations for heat distortion and snow load criterion…

Project Title : FENDER DESIGN Objective : The main object of this project is to design the BIW(Body in white) of front fender using the fender skin data and master section as the into data by using NX CAD. Introduction : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body…

Project Title : FENDER DESIGN - WHEEL ARCH Objective :  Calculate the wheel arch area and prove whether the car will pass the europen standards or not. Introduction of Wheel Arch :                              The design of the wheel arch of…

PROJECT TITLE :  SECTION MODULUS CALCULATION AND OPTIMIZATION. OBJECTIVE :  The main objective of this project is to learn the basic features, tools, and the section modulus calculation and optimization using NX CAD. INTRODUCTION : Section Modulus : Section modulus is a geometric property for a given cross-section…

PROJECT TITLE : HOOD DESIGN OBJECTIVE :                      To design outern panel, inner panel and create the assembly of hood outer and inner panel with the hinge and striker. Understand the mechanism behind the design of hood, then development and its safety features…

UNDERBODY COATING : A cars underbody is most prone to corrosion. Underbody coating is provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rail and other inner cavities that are not physically accessible but are prone to corrosion. Benefits : minimizes…

Title of the project : BENCHMARKING  OBJECTIVE :  Mr. D.S. Pughazhyendhii is a married man who lives in bangalore which is a highly crowed city. His family comprises five members including his wife, five-year-old boy, his father, his mother. he visits his native place madurai which is 500kms away from bangalore…

TITLE OF THE PROJECT : Advanced Sheet Metal Design Using NX Cad Challenge_7_Metal Bracket-2. OBJECTIVE : To design a metal bracket-2 using siemens NX Sheet Metal application. INTRODUCTION :  SHEET METAL DESIGN : NX Sheet Metal Design provides the design professional with a complete set of tools to efficiently…

TITLE OF THE PROJECTS : Advanced Sheet Metal Design Using Siemens NX-Cad Challenge_6_Bracket. OBJECTIVE : To design a Bracket using Siemens NX-Cad Sheet Metal application. INTRODUCTION :  Sheet Metal Design : NX Sheet Metal Design provides the design professional with a complete set of tools to efficiently create…

TITLE OF THE PROJECTS : Advanced Sheet Metal Design Using NX Cad Challenge_5_Odd Shaped Enclosure. OBJECTIVE : To design the odd shaped enclosure by using siemens NX Sheet metal Application. INTRODUCTION :  Sheet metal Design : NX Sheet metal design provides the design professional with a complete set of tools to…

 Title of the Project :- Advanced Sheet Metal Design using NX cad Software Challenge_2_Box Assembly. Objective :- To design a box assembly using siemens NX Sheet Metal Application. Introduction : SHEET METAL DESIGN : NX Sheet metal design provides the design professional with a complete set of tools to efficiently…

TITLE OF THE PROJECT :- Advanced Sheet Metal Design using NX cad Challenge_1_Casing Design OBJECTIVE :- To design a sheet metal casing design as per dimenstions by using NX cad software. INTRODUCTION :- Sheet Metal Design :- NX Sheet Metal Design provides the design professional with a complete set of tool…

COMPONENT : RADAR MAST                  Front View :                   Right View :                    Top View :                …

                                                  MODELING AND RENDERING OF AMERICAN CHOPPER BY USING SOLIDWORKS     1) INTRODUCTION : Solidworks is used to develop mechatronics systems…