3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

Aim :- Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level

Procedure :-

step I :- click on ceiling under Architecture tab

step II :- we have two option under ceilling option one is the automatic ceilling and sketch ceilling we just select sketch ceilling

step III :- various option are seeing to draw ceilling here i just use pick line option

step IV:- select carefully all outer line and then click thickmark.

step V:- we can check it on 3d view

Result :- well understood to draw ceillling

Aim:- Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees

Procedure :-

step I :- select first floor and click on roof under the architecture tab

step II :- select option roof by footprint

step III :- various option are seeing to draw roof here i just use pick line option

step IV:- select carefully all outer line and then click thickmark.

step V:- we can check it on 3d view

step VI :- select roof and click on property browser and change sloop to 10 degree.

Result :- well understood to draw roof and how to change roof sloop.

Aim :-

Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans

a. Architecture plan must have walls, floors, and all the components placed within the building
b. Structure plan must have details of only walls, floors, and columns

Procedure :-

step I :- select plan view under the view tab

step II :- we have multiple option here i will chose floor plan and click the edit type option and click ok this is for architecture plan

step III :- if we want to see structural plan select plan view under the view tab.

step IV :- we have multiple option here i will chose structural plan and click the edit type option and click ok this is for structural plan.

Result :- well understood to create Architecture plan Structure plan.

Aim :-

Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file

a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans

b. The Structure plan dimensions must include details on the position of all the walls and interior walls with reference to grids. Locate all the framing components of the building with reference to a fixed point using Structural plans

Procedure :-

step I :- go to Annotate tab and select linier or angular and just provide all dimension for architecture plan

Step II :- go to Annotate tab and select linier or angular and just provide all dimension for Structure plan

Result :- well understood to use of annotate toolbar.

Aim :- Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views

Procedure :-

step I :- click sheet under the view tab

step II :- we have various paper sizes here i will chose A1 metic immidiatle sheet will be created

Result:- well understood to Create a sheet template

Aim:- Using the elevation tab create the elevation views, looking at your building from East, North, South, and West

Procedure :-

step I :- click elevation under the view tab

Step II:- create elevation east, west, nort and south direction view.

Result:- well understood to create the elevation views

Aim:-Produce section cut through each room either cutting across longitudinally or in a transverse direction

Procedure :-

step I :- click section under the view tab

step II:- create section for different room as per requirement

Result:- well understood to create the section cut through each room.

Aim:-Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser

Procedure :-

Result:- well understood to Classify the views, Plan Views, Section Views, and Elevation views.

Aim:-

Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations

Add additional sheets based on the sections created in your Revit file

Procedure :-

step I :- click section under the view tab

step II :- we have various paper sizes here i will chose A1 metic immidiatle sheet will be created

Result:- well understood to Create sheet template.

Aim:-

Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting.

Procedure :-

step I :- click 3d view under the view tab

step II :- select camera to create view