Aim: To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component. Objectives:  Creation of Tooling Axis. Creation of Class B and Class C surface. Creating a solid part out of Surface modelling. Draft Analysis of Class A surface and final…

AIM: Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5 mm…

AIM: To Create the Door Handle Component from the given Class-A surface. Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle.Attach B side Features in the component. perform the Draft analysis on the model.  Procedure for the projects Creating the tooling axis…

AIM: to make a model from the provided class-A surface.   INTRODUCTION:   CLASS-A SURFACE: A surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface. CLASS-B SURFACE: A surface below a certain thickness from the class-A…

AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. Class A  Visible surface is a Class-A surface. It provides the style team's look for the component, which the part…

                                                                                 Attachment Feature Creation (Dog House)…

 AIM: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the…

Week 12- Final project: Development of a Door Trim panel Door trim panel is creation of CAD model considering following inputs as like in OEM and tier1 companies Class A surface is givin but after applying boundries check, it has been found there is some improvement needed to be actioned to get a closed surface. Nominal…

BENCHMARKING : It is an organised comparison of similar goods, services, or methods along some performance variables. By benchmarking one can include the better options available in competitors and eliminate the bad ones. This results in the development of the best product available for the customer.  Other than improving…

UNDERBODY COATING   Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are…

                                                                      HOOD DESIGN OF A CAR   AIM : To design the hood of a car with the given input Outer panel and its dimensions. Hood Introduction : The hood (North American English) or bonnet (Commonwealth English) is the hinged cover over the engine of motor vehicles.…

                                                 SECTION MODULUS CALCULATION AND OPTIMIZATION AIM :             To calculate the Section modulus for the given hood model…

                          Fender Design - Wheel Arch AIM:        To decide whether the given Fender design passes the European standards or not.   GIVEN DESIGN:   European Regulations Requirement:   Take the outline…

                                                                    DESIGN OF CAR FENDER   CAR FENDER :            …

                                                                              ROOF DESIGN   Aim: To design & develop…

                                                                     CAR BACK DOOR DESIGN Aim:           To design back door/Tail Gate of car using given outer class 'A' surface and also withstand the impact during Collision.   What is back door of a car?  A door which is located at the rear side of a car which gives access…

                                       Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical…

                                          Wiring harness routing & packaging Rules Week 3 Challenge   WIRING HARNESS ROUTING AND PACKAGING RULES (Clips, Backshells & Corrugated tubes) Aim:- The aim of the project is to study and understand the different models of the clips, back shell and corrugated tube and convert the…

                                                     Wiring harness design in CATIA V5 - 3D modeling   Aim:- To Route the following harness layout in the Electrical workbench. Add…

                                   Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle…

                                                                        WIRING HARNESS ROUTING   AIM: To flatten the wire harness assembly…

                                                              WIRING HARNESS DESIGN PROJECT 1  AIM:- Design and develop the Wiring harness on Given V6 Engine and…

AIM:  Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and industry based…

Q1 Ans BIW - Body In White BIW refers to the welded sheet metal components which form the structure of the vehicle to which the other components (like engine, chassis, exterior & interior trims) will be married or assembled. The stage in automotive design or automobile manufacturing in which the car body sheet metal components…

1)What is the process of project execution activity?                         1)RFQ received -    This id the first step in any project. RFQ stands for Request for Quotation. In this customer specifies his requirements,specifications etc. in…