Aim:           To create  the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft…

     Aim:            To create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. …

 Aim:        Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Objective : To design…

DESIGN AND DRAFT ANALYSIS OF BUMPER ;             Aim:           Create the Bumper Plastic component through the given Class-A surface. and create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle and at the end perform the…

AIM ;      Create the screw boss and dog house for the centre console coin holder considering the design rules mentioned in the video. General Rules for Screw bosses ; Draft of 0.5 degree on walls of boss Thickness is 40% of the nominal wall at the base. Height to diameter ration-3:1 Fillet radius of max…

AIM: To create Plastic design and attach the Engineering features and generate the Draft Analysis for the given Door Applique Class A model.   PROCEDURE: 1.Check for any openings in the given model Door Applique by using BOUNDARY. In BOUNDARY > select edges - select the surface to create the boundary…

INTRODUCTION  MASTER SECTION:           Master sections development takes place during feasibility check and concept validation stages of the product life cycle. These are typically the guides for design requirements and which decides the component packaging after the development of the…

AIM: To Create the Core and cavity blocks for the switch bezel component.   DESCRIPTION:      1. CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

AIM:  The aim of this project is to model a butterfly valve and to apply GD&T to the different parts of the butterfly valve and the assembly. INTRODUCTION ; Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves…

BENCHMARKING : It is an organised comparison of similar goods, services, or methods along some performance variables. By benchmarking one can include the better options available in competitors and eliminate the bad ones. This results in the development of the best product available for the customer.  Other than improving…

AIM: Study the underbody coating used in automobile industries. Objectives: Study about underbody coating Study about types of underbody coating and its advantages and disadvantages. Procedure: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile.…

Development of a Door Trim panel Aim:  Creation of CAD model considering CLass A surface, nominal thickness, and attachment features. Abstract: The project report explains steps and procedures followed while developing the Door Trim Panel of a car using CATIA V5. Using the CLASS-A surface and master sections as input,…

Aim :         To design a Hood outer panel, inner panel and the necessary reinforcements by the given Master section and design parameters.   Theory : Hood is a main component of front portion of a car. It is an opening body panel that covers the engine in front engine vehicle. It consist of an outer panel and inner panel.…

SECTION MODULUS OF THE HOOD Objective: To find the section modulus of the hood and optimisation to improve the overall section modulus. Section Modulus: The section modulus (S) is geometric property of the cross section used for designing beams and flexural members. It does not represent anything physically. Formula of…

Objective:             To calculate the wheel arch area of the given fender and analyse whether the fender will pass the european regulation. Introduction:             Wheel Arch is the shaped part of the bodywork of a car or other vehicle that allows the wheel…

REPORT - FENDER DESIGN    AIM:        To design a  front fender of a car by following the given master section as per the design considerations of OEM.   OBJECTIVE :          Design a Fender Model with the necessary mounting with a given class A surafce.…

 AIM : For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis.Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs.Suggest…

AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

  Aim :  Q1. Download the following cad data & define it as Electrical support using the Electrical Part Design Workbench. Define all the necessary properties. P clamp Note: if you face any issue with point definition, or point selection, Right-click on the point definition window and use the reset option.…

Aim: 1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors: • DT06-4S • DT06-6S • DT06-2S • DT06-08SA Connectors Layout Design: Steps to be followed:…

AIM:          To design the back door of the carr and  make the inner panel for the back door and also design the necessary re-enforcements. SOFTWARE: NX 12.0 INTRODUCTION:        The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often a hatch at the…