Aim : write a program for air standard cycle  to plot a pv diagram and calculate thermal efficiency Introduction : The Otto cycle is a set of processes used by spark ignition internal combustion engines (2-stroke or 4-stroke cycles). These engines a) ingest a mixture of fuel and air, b) compress it, c) cause it to…

Aim : Write a program to simulate the transient behaviour of a simple pendulum and to create an animation of it's motion.Governing Equation : second order differential equation`(d^2 θ)/(dt^2 ) +b/m (dθ)/dt +g/l(sinθ)=0`where,g = gravity in m/s2,L = length of the pendulum in m,m = mass of the ball in kg,b=damping coefficient.Objective…

Aim :  To design and simulate the Multi-Body Dynamics of an Internal Geneva Gear Mechanism using SOLIDWORKS Objective : Create 3D models for driver and driven wheels. Perform motion analysis by rotating the driver wheel  Obtain the following plots introduction :  The Geneva drive or Maltese…

Aim: To model parts of piston assembly and simulate the piston assembly in three condition. Objective: To model parts  and assemble the Piston Assembly. To perform motion analysis at different wrist pin offset values. To analyse the resulting plots.   Steps : create 3d model and assemble them . to perform…

Aim :To design and perfotm motion analysis of an IC engine valve train of different cam-liftsObjective:Valve Lift. The contact force between Cam and Push RodPushrod and Rocker ArmRocker Arm and ValveExplain why the contact force between the Rocker arm and valve varies while measuring with respect to the…

 Aim : Constructing a Planetary gear system with four planet gears and analyzing the angular velocities for different cases Objective : Design planetary gear with the following parameters:  Ring Gear: Module = 2.5 (use the metric system in design modeller) Number of teeth = 46 Sun Gear: Number of teeth = 14 Input…

Aim : write a program for air standard cycle  to plot a pv diagram and calculate thermal efficiency Introduction : The Otto cycle is a set of processes used by spark ignition internal combustion engines (2-stroke or 4-stroke cycles). These engines a) ingest a mixture of fuel and air, b) compress it, c) cause…

Aim : write a program for air standard cycle  to plot a pv diagram and calculate thermal efficiency Introduction : The Otto cycle is a set of processes used by spark ignition internal combustion engines (2-stroke or 4-stroke cycles). These engines a) ingest a mixture of fuel and air, b) compress it, c) cause…

Aim : Write a program to simulate the transient behaviour of a simple pendulum and to create an animation of it's motion. Governing Equation :  second order differential equation `(d^2θ)/dt^2+b/m(dθ)/dt+g/l(sinθ)=0` where, g = gravity in m/s2, L = length of the pendulum in m, m = mass of the…

Aim : Write code to fit a linear and cubic polynomial for the Cp data and Plot the linear and cubic fit curves Theory : Curve fitting is the process of constructing a curve, or mathematical function, that has the best fit to a series of data points possibly subject to constraints. Curve fitting can involve…

Aim:  Frequency Analysis of a rotating shaft Objectives :1. To create 3D model of a rotating shaft.2. To perform frequency analysis on the rotating shaft and nd out the critical frequencies. Introduction:The resonant frequency is the oscillation of a system at its natural or unforced resonance. Resonance occurs…

Aim: To analyze the ow over a NACA0017 airfoil For different angle of attacks and to compare the lift and drag forces. Objectives: To do a CFD analysis of a NACA0017 airfoil. Use different different angle of attacks for the airfoil as 0, 2, 4, 6, 8 & 10 degrees. Run the flow analysis to obtain Velocity contour and…

AIM: Creating a Rankine Cycle Simulator & Calculating the state points of the Rankine Cycle based on user inputs, Plotting the corresponding T-S and H-S plots for the given set of inputs Theory: Rankine cycle is the most basic thermodynamic cycle for any steam powerplant. It starts with heating of water in boiler at…

Aim:To perform a buckling analysis on a cyclone separator stand by creating a metallic stiffener on the legs of the stand and run the analysis to nd out the change in buckling factor of safety Objective : To perform a buckling analysis on a cyclonic separator stand  To create a metallic stiffener on the legs of the…

Aim: To Perform a static analysis on two models of a plate with holes via SolidWorks, one analysis for a plate with one hole and one analysis for a plate with three holes. Finally, compare the obtained results between the two plates. Objective :  To perform a static analysis on two models of plate with holes (plate…

Aim:To do a comparison between three types of beams in terms of stress, displacement, and strain generated during the bending load conditions by doing FEA in SOLIDWORKS Objective : To model three types of beam ( Rectangular beam , I-section beam & C-section beam ) For the load value of 1500N analyse the deection/bending…