Gas Tank : https://drive.google.com/open?id=1VreDn_JB_R7KE5yFkqpfUdbnZLQr3F2y                                  X------------------------X-------------------------X Assembly : All part models and assembly are in a single ZIP file.  …

1. Transmission Belt : https://drive.google.com/open?id=1yYcap7mjpUyS_4K3EsssJ1yH1r6mXDxu St   2. Kickstand : https://drive.google.com/open?id=1UJrMirzin2KY4TkoRxFVSVWBFPVhNESB   3. Front Fender : https://drive.google.com/open?id=1oAAxCNouQ1NpoeuDdGoK_zNqXmiLrR6O   4. Rear Fender : https://drive.google.com/open?id=1vdWkYD4f5_3NVFTcRhIjgvOlv6TVpal7…

1. Chassis : https://drive.google.com/open?id=19IrFHx1MRgHsVnQhgejm3auLqDw94jrV                              X------------------------X------------------------X   2. Engine : https://drive.google.com/open?id=1zkEBtXo6ov8vGT_oqKkN8li-GxTalnGb…

1. Oil Tank : https://drive.google.com/open?id=1n9dsRrbaVbuvAjse2CmEos0yxSFC15ga Steps : 1. Create a 2D sketch on Top plane and Surface extrude. 2. Create a 2D sketch on Mid plane Surface extrude. 3. Trim the unrequired faces. 4. Create fillet at all the edges of the Oil Tank. 5. Change Face colors. 6. Create a Section…

Objective:  Mesh the component given below and assign thickness, also with provided quality criteria: Component- Hood Target Element Length = 5mm S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2mm 6 Max. Length 8mm 7 Min angle…

Objective Create 1D elements on the following component with given cross-section and DOF a. Rod element:- with only translational DOF and RBE2 link Cross-Section:BOX- Dimension a= 12 mm                               dimension b=10 mm    …

1. Rear Wheel : https://drive.google.com/open?id=1JqLa-tO4ngFOE-2r-L0-yzQmeVO5QfhG                                 X---------------------------X-----------------------X   2. Front Fork : https://drive.google.com/open?id=17-wi974_KctSzVQk-aE_n12ATmNkzwEy…

Model 1 Objective : To create Tetra mesh for Housing model according to given element criteria. Criteria : Elements sizes: Min- 2mm, Target- 5mm,Max- 7mm; Tet collapse: 0.15 Procedure :  1. Open a new RADIOSS format file in Hypermesh and import the housing CAD model. 2. Delete all the solids from the components,…

Objective: Create connector and Attach the various parts of the given model as the information below: 1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 3…

Objective:  Mesh the component given below and assign thickness, also with provided quality criteria: Component- Hood Target Element Length = 4mm S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2mm 6 Max. Length 6mm 7 Min angle…

Objective: Carry out the geometry cleanup operation on the given 3 files which are as: Practice  Clip Repair Mounting Bracket There should not be any free edges, convert all of them into refine geometry. Clean the geometry. Extract midsurface. Clean midsurface geometry. Ignore holes less than dia 5mm. Create…

Aim: 1. To calculate the speed of sound and time of steel rail by using material property. 2. Engine file editing to monitor stress wave. 3. To apply 2D and 3D mesh (tetra and hexa) for the components. Target Element Length = 5mm S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 60 3 Warpage 15 4…