Full course · free on YouTube · 1 h 34 min

Vehicle Dynamics workshop in Adams/Car: free, 1.6 hours

A single 1.6-hour recorded live workshop from February 2019, run as a software demonstration with audience questions. It shows the Adams/Car template, subsystem and assembly levels, a wheel rate check, KNC test types and a bump steer design of experiments.

25 chapters · published 2 Feb 2019 · 3,969 views as of 20 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical and automotive students who know basic suspension terms and want to see how Adams/Car is used to tune wheel rate and hard points.

What will you learn?

  • How Adams/Car separates templates, subsystems and assemblies, and what is defined at each level
  • How a spring stiffness and a motion ratio give a hand-calculated wheel rate
  • How a parallel wheel travel test and the post-processor give the simulated wheel rate
  • Why the simulated wheel rate comes out higher than the hand calculation: bush stiffness resisting wheel travel
  • What the KNC tests (bounce, roll, steer, compliance) are used to tune
  • How an Adams/Insight DOE finds which hard point affects bump steer

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:004 min · 3 chapters

    Adams/Car architecture and the double wishbone template

    The instructor places Adams/Car among the Adams modules (View, Engine, Flex, Chassis), explains its three levels (template, subsystem, assembly), and opens the double wishbone template to show the lower arm, knuckle, upper control arm, ball joints and tie rod.

    Chapters
    • 0:00Adams modules and where Adams/Car fits
    • 1:35Three levels in Adams/Car: template, subsystem, assembly
    • 2:32Double wishbone template: parts and joints
  2. 4:255 min · 1 chapter

    Subsystem properties and a bush change

    At subsystem level the demo sets mass and inertia per part, sprung and unsprung share, linear spring and damper data and bush stiffness. A bush's rotational stiffness is raised and the new bush swapped in as a starting value, to be tuned later in the assembly.

    Chapters
    • 4:25Subsystem level: mass, inertia, spring, damper and bush properties
  3. 9:3218 min · 6 chapters

    Tuning wheel rate: hand calculation against Adams

    A default spring of 1250 N at 10 mm gives 125 N/mm. With a motion ratio of 0.571 the hand calculation expects a wheel rate near 41 N/mm. A parallel wheel travel test of ±15 mm gives a slope near 55 N/mm, The measured motion ratio is 0.506, which alone would lower the rate to about 32 N/mm, so the extra stiffness comes from the arm bushes the hand calculation leaves out.

    Chapters
    • 9:32Assembly level and what tuning wheel rate means
    • 11:20Default spring stiffness read from the spring data
    • 12:26Motion ratio and the hand-calculated wheel rate
    • 17:52Post-processor: wheel rate from the force-travel slope
    • 20:52Why Adams and the hand calculation disagree: motion ratio
    • 23:45Bush stiffness contribution to wheel rate
  4. 27:3712 min · 4 chapters

    Questions, templates and KNC tuning

    Answers cover MATLAB versus Adams, FSAE use, the ready-made suspension templates and why hard points, unlike spring rate, need kinematics and compliance (KNC) tests. A slide lists the bounce, roll, steer and compliance tests and what each is used to tune.

    Chapters
    • 27:37Questions: MATLAB versus Adams and FSAE use
    • 29:46Ready-made suspension templates and who uses Adams
    • 32:39Choosing wheel rate, then hard points: KNC tuning
    • 34:28Kinematics and compliance tests and what each tunes
  5. 39:2113 min · 4 chapters

    What the model leaves out, air springs and bushes

    The speaker says a model only holds what you choose to include, and shows the knuckle stiffness bush added for transient steer response. Air springs replace the coil spring, and bush stiffness and compliance steer targets are discussed along with testing real bushes.

    Chapters
    • 39:21What the model leaves out: flexibility and knuckle stiffness
    • 42:50Air springs in place of coil springs
    • 44:11Setting bush stiffness on a real car and compliance steer
    • 49:52Anti-squat and anti-dive outputs; Adams geometry limits
  6. 52:2215 min · 2 chapters

    Dampers, steering, tyres and road profiles

    The speaker explains why dampers are tuned by subjective assessment, adds a steering subsystem to the assembly, and compares spring and tyre property files. A full-vehicle assembly is opened and a Belgian block road profile is shown.

    Chapters
    • 52:22Dampers, adding steering and multibody dynamics
    • 57:03Tyre property files and road profiles
  7. 1:06:5822 min · 3 chapters

    Bump steer study with the Adams/Insight DOE tool

    Bump steer is defined as the slope of toe against wheel travel. A design objective (maximum toe) is checked in the post-processor, the wheel travel script imported, and the outer tie rod Z position varied by 1% in a four-run sweep.

    Chapters
    • 1:06:58Bump steer and the Adams/Insight DOE set-up
    • 1:14:59Tie rod Z factor and the four-run sweep
    • 1:17:49Roll stiffness and a spring-rate spreadsheet
  8. 1:29:095 min · 2 chapters

    DOE results and the sensitivity study

    The simulations finish and the response is plotted against trial: moving the tie rod hard point changes toe. A larger earlier study on lower control arm hard points is shown, with the roll centre height most sensitive to one coordinate.

    Chapters
    • 1:29:09DOE results: tie rod position changes toe
    • 1:31:56Sensitivity study of lower control arm hard points

Is the Vehicle Dynamics Workshop (Adams/Car) course really free?

Yes. All 1 h 34 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 2 Feb 2019 and had 3,969 views as of 20 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Vehicle Dynamics Workshop (Adams/Car) course take to finish?

The video runs 1 h 34 min across 25 chapters. At one hour a day that is about 2 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Bump steer study with the Adams/Insight DOE tool" (22 min), so give it its own days.

Does the free Adams/Car course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Suspension Design using Adams (free lessons), then Suspension Design using ADAMS (₹40,000), then Vehicle Dynamics using MATLAB (₹40,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need to buy Adams to follow a vehicle dynamics workshop like this?

In this 2019 recording the speaker advises against buying it. They suggest using the copy or student edition your college may have, which they describe as free for students. They also say Adams ran on their 4 GB, i5 laptop, so it does not need a high-end machine.

Why does the wheel rate from Adams differ from the hand calculation?

In the demo the hand calculation gives about 41 N/mm and Adams about 55 N/mm. The speaker names two approximations: the straight-link motion ratio formula (0.571, against 0.506 measured in Adams) and the bush stiffness, which the hand calculation leaves out. The measured motion ratio alone would give about 32 N/mm (125 × 0.506²), so it is the bushes, resisting wheel travel, that raise the rate.

Can Adams be used without a CAD model of the suspension?

Yes, according to the speaker. Adams works on the mechanics, so the links on screen are only graphical. Hard points are entered as coordinates, and a CAD file can be imported but the speaker says that is generally not advised. Detailed part geometry cannot be built in Adams.

Last updated 20 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 20 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Vehicle Dynamics Workshop (Adams/Car) and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Vehicle Dynamics Workshop (Adams/Car) course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.