Full course · free on YouTube · 1 h 27 min

Race car design for BAJA and FSAE: free, 87 minutes

A single 87-minute recorded live workshop from Skill-Lync, taught with slides, hand sketches on a graph sheet and a closing software demo. It covers double wishbone suspension geometry, camber and toe targets, roll centre, bump steer and a simulation of the same ideas in Adams.

24 chapters · published 2 Feb 2019 · 5,045 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical and automotive students on BAJA or FSAE teams who know basic vehicle dynamics and want to learn how suspension geometry is chosen and checked.

What will you learn?

  • Explain why double wishbones are used on race cars and which parts can be shared front to rear
  • State the camber targets for cornering versus acceleration and braking, and why static camber is a compromise
  • Find the instant centre and roll centre of a double wishbone from the link geometry
  • Compare parallel, converging and unequal-length links for camber change in roll and in bump
  • Place a tie rod so that toe does not change with wheel travel (bump steer)
  • Read camber and toe plots from a bump test and a constant-radius cornering run in Adams

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:0015 min · 4 chapters

    Suspension goals and why the double wishbone

    The instructor states the aim as keeping the wheel at its best camber and toe to the road, then explains why double wishbones suit race cars: front and rear can share arms and uprights, and hard points can be moved freely. Camber, toe and wheel rate are named as the three values to optimise.

    Chapters
    • 0:00Why suspension angles matter: camber, toe and peak tyre force
    • 4:06Why race cars use the double wishbone
    • 9:03Kinematics, hard points and bushes
    • 12:20Bump and roll, and the three values to optimise
  2. 15:0710 min · 3 chapters

    Camber targets for cornering, acceleration and braking

    Positive and negative camber are defined, and camber thrust is explained as the reason both wheels should lean towards the turn centre in cornering. For acceleration and braking the target is zero camber. A short question break covers banked roads and why lower control arm brackets are stronger.

    Chapters
    • 15:07Camber sign convention and camber thrust in cornering
    • 19:50Zero camber for acceleration and braking
    • 21:15Questions: banked roads and control-arm brackets
  3. 24:414 min · 2 chapters

    Instant centre, roll centre and roll axis

    The double wishbone is treated as a four-link mechanism. Extending the two arms gives the instant centre, and joining that to the tyre contact patch gives the roll centre on the vertical plane. The chassis is then taken to roll about the axis through the front and rear roll centres.

    Chapters
    • 24:41Swing arm, four-link mechanism and instant centre
    • 27:04From instant centre to roll centre and roll axis
  4. 29:0014 min · 3 chapters

    Parallel equal-length wishbones worked on a graph sheet

    The design is worked by hand on a graph sheet. With parallel equal arms the instant centre is at infinity and the roll centre sits at ground level. A 4 degree chassis roll gives the same camber change, in the wrong direction for cornering, while pure bump and rebound give zero camber.

    Chapters
    • 29:00Parallel equal-length wishbones: the graph-sheet method
    • 32:50Camber in roll with equal links (wrong direction)
    • 39:43Camber in bump and rebound with equal links
  5. 42:537 min · 2 chapters

    Reducing roll and adding static camber

    Two fixes for the equal-link problem are tried. Softer roll resistance from springs and anti-roll bars cuts roll but conflicts with keeping springs soft for grip. Static camber of -4 degrees brings the outer wheel upright in a 4 degree roll, but it hurts straight-line grip and wears one tyre edge.

    Chapters
    • 42:53Fix 1: softer roll resistance with springs and anti-roll bars
    • 44:55Fix 2: static camber and its straight-line cost
  6. 50:0710 min · 3 chapters

    Converging and unequal-length links

    Converging links are drawn for the same 4 degree roll. The outer wheel gains only about 2 degrees of camber, described as 50% camber recovery, so -2 degrees of static camber is enough. The instructor then adds a shorter upper link to keep the roll centre steadier.

    Chapters
    • 50:07Converging links and camber recovery
    • 55:45Optimum camber angles and the static camber compromise
    • 58:18Converging unequal-length links
  7. 1:00:0713 min · 3 chapters

    Toe, bump steer, summary and suspension loads

    Bump steer is introduced as toe changing with wheel travel, and the tie rod is placed so it passes through the instant centre. A summary of the front-view requirements follows. The last theory part sets up the 3g vertical load case and how its force is shared between the spring, the arm and the chassis mounts.

    Chapters
    • 1:00:07Toe, bump steer and tie-rod placement
    • 1:05:31Summary of the front-view requirements
    • 1:07:26Suspension loads: the 3g vertical load case
  8. 1:12:5114 min · 4 chapters

    Simulation in Adams

    In Adams, a default car model with parallel links is run through bump and rebound to read toe, then a repositioned tie rod is compared. A full-vehicle constant-radius cornering run (33 m radius) is repeated with converging hard points and the outer front wheel camber is plotted.

    Chapters
    • 1:12:51Adams: opening the full-vehicle model
    • 1:15:40Bump steer test with parallel links and a moved tie rod
    • 1:20:44Full-vehicle constant-radius cornering, parallel links
    • 1:23:05Converging hard points and the camber result

Is the Workshop on Race Car Design Principles for BAJA & FSAE Cars course really free?

Yes. All 1 h 27 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 2 Feb 2019 and had 5,045 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Workshop on Race Car Design Principles for BAJA & FSAE Cars course take to finish?

The video runs 1 h 27 min across 24 chapters. At one hour a day that is about 2 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Suspension goals and why the double wishbone" (15 min), so give it its own days.

Does the free Adams course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Suspension Design using Adams (free lessons), then Suspension Design using ADAMS (₹40,000), then Vehicle Dynamics using MATLAB (₹40,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Which software does the BAJA and FSAE suspension workshop use?

The simulation part is shown in Adams, which the instructor says they have used for about ten years. The instructor also says any other multibody package can be used, and that the first half of the design is done by hand on a graph sheet, so no software is needed for the theory.

What do you need to know before watching this suspension design workshop?

The instructor assumes you know the basics of vehicle dynamics. Four-link mechanisms and instant centres from engineering mechanics are used, and free-body diagrams and Newton's second law appear in the load case. No prior suspension design experience is stated as required.

Why does the workshop reject parallel equal-length wishbones?

With a 4 degree chassis roll, equal parallel links give the outer wheel 4 degrees of camber in the wrong direction for cornering. Bump and rebound give zero camber, which suits acceleration and braking. Converging links cut the camber gain to about 2 degrees, which the instructor calls 50% camber recovery.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Workshop on Race Car Design Principles for BAJA & FSAE Cars and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Workshop on Race Car Design Principles for BAJA & FSAE Cars course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.