Unlock all 34 lessons of Suspension Design using ADAMSFull course ₹40,000 · paid
Why Suspensions Exist and Common Suspension Architectures
A free lesson from Skill-Lync's Suspension Design using ADAMS course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Need for Suspension Topologies”
What will you learn in this free Suspension Design using ADAMS lesson?
The instructor explains that a suspension handles ride isolation and handling. The lesson then identifies parts on an Audi R8 double wishbone, an Audi TT McPherson strut, a twist beam, five-link and four-link multi-links, a solid axle and a push rod Formula 1 layout, and sets a comparison write-up.
- Ride isolation versus handling control forces
- Double wishbone versus McPherson strut packaging
- Twist beam, multi-link and solid axle rear setups
- Push rod and bell crank aerodynamic benefit
What comes after lesson 2?
The next free lesson is lesson 3, “Instant Center and Instant Axis in Suspension Geometry” (8 min). Later in Skill-Lync's Suspension Design using ADAMS course (paid): lesson 4, Camber gradient seg 1; lesson 5, Camber gradient seg 2; lesson 6, RCH Scrub. The full course has 34 lessons (13 h 48 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
So first, we're going to talk about the need for suspension, why we need a suspension system in the vehicle. So the suspension system is primarily responsible for two things. So one is isolation, so isolating the body from road inputs by providing vertical compliance. So vertical compliance is basically the spring stiffness, the spring rate. If you look at the picture here, if you look at this one, you can see that without a suspension system in this vehicle, all the forces acting on the tire would go directly into the body, and eventually the driver would feel it.
So you can see how much isolation, how much vertical compliance this whole system is providing. So that is one of the main functions of the suspension. So that comes under ride. And the second thing would be handling. So if you look at this picture here, the Formula One car, so here you can see, so here we don't care much about isolation. So here it's all about reaction to control forces. And by control forces, we mean the forces generated at the tire contact patch during, or it can be even the wheel center.
So this happens during acceleration, braking, or cornering. So the suspension needs to react to these forces, and it also needs to control the transfer of these forces into the body. So good suspension design is very crucial to achieve the ride and handling balance. So you can see the two photos here, or the two animations here, are completely different applications. So you can compare the picture here to your left to an SAE Baha vehicle, and the one on the right to your Formula SAE car. So you can see that there are two very specific functions, ride and handling.
But in a road car, you need both. You need isolation as well as you need handling as well. So you need to design the suspension very well to achieve that balance between ride and handling. In this section, we're going to look at some common suspension architectures. So we're going to do front suspension first, and then rear suspension. We're also going to take a look at the racing suspension architectures that is common in Formula 1 and even the FSAE cars. So first, let's start with the front suspension.
So here on the left, it's a double wishbone setup from the Audi R8. So we're going to look at all the different parts here. So you have the lower wishbone here. So this is your lower control arm or lower wishbone. And here you have your upper control arm, your spring and damper assembly here. So this is mounted to the body. And so you can see the roll bar. So this is your anti-roll bar. This link here is the tie rod, which controls the steering motion. So this is your steering input.
The pinion is attached here. So when you turn the wheel, this rotates and the rack moves left to right. And that pushes the tie rod and then you get the steering action. So this is your front drive unit or front differential. So the R8 is a four-wheel drive sports car. So you have the drive shaft coming into this. And then you can see the two half shafts. So you can see the half shaft here and here. And then this is the knuckle. So you can see the two control arms attached to the knuckle.
So this is called the knuckle or the upright. Sometimes it's also called the wheel carrier. So this is your double wishbone setup. So we've just looked at all the various components there. And so the main thing with this suspension is you need a lot of space in this area here. So in this area, you need a lot of space because you can see the control arms are wide. And so that's one of the potential disadvantages or, you know, packaging-wise, it's a little hard here. And which brings us on to the McPherson strut.
So here the main advantage is packaging. So you can see it's very clean package. All you need is vertical space to... So this is very tall. The strut assembly is very tall. So you just need vertical space to somehow package this. So this is common in most of the front-wheel drive cars, front-wheel drive passenger cars. So there is a lot of vertical space for the strut mount. So again, here we'll go through all the components. So this is the strut. So one thing here, you'll notice that this looks very similar to the damper assembly here.
But we don't call that a strut. So we call this strut and we just call that, you know, spring or damper assembly. So the main thing here is the strut is a load-bearing member, which means it's kind of supporting the entire suspension. Because here you have two control arms. Here the upper control arm and the lower control arm mounting to the body of the subframe. And that kind of carries the whole wheel. And so that's carrying the suspension. But on this setup, your strut is what's carrying the suspension.
You don't have an upper control arm. So if you take the strut out, the whole system will collapse. So that's why it's called a load-bearing member. And here you have the lower control arm. And that's mounted to the subframe. So this structure here is your subframe. So this is from an Audi TT. And then the control arm, the strut, and this is your knuckle. So the TT here, again, is a four-wheel drive car. So you can see the half shafts here. So even though the setup is common in front-wheel drive cars, you can use it in, you know, four-wheel drive or rear-wheel drive cars as well.
The only important consideration here is the vertical space. The R8 is a low sports car. So if the car is very low, getting this point, you know, mounting this point very high becomes difficult. So for all your race car applications or your low sports car, the double wishbone is the best setup. So this goes to the body. So it's called the top mount. And then you can see the roll bar here. And this is your steering system. So here, your input, your steering input goes here.
And you have the rack, which eventually pushes on the tie rod. And you can see the tie rod here. It's somewhere. Yeah, that's your tie rod. And this link here, this connects the roll bar to the strut. That's called a drop link. So when the suspension moves up, say when this side moves up, it pulls on the drop link. And the drop link pulls on the roll bar. And the roll bar is attached here to the subframe. So there will be another mount on the other side.
So this is your roll bar to subframe. So since it is constrained in two locations here and on the other side as well, when you put a force on this, say when the suspension goes in compression, you put a vertical force on this, it twists. So you're holding it here. So the entire bar twists. And on the other side, it pushes the other side down. So that's what gives you that anti-roll action. So when this side goes up on this end, it pushes this down. So also I'd like to add that even though we call this an independent suspension, because of this roll bar, it's not truly independent.
It's still connected. The two ends are connected by the roll bar. So yeah, these are the major components. So we've not gone into the working of the suspension. We're just trying to identify the different parts and look at the architecture overall. So moving on to rear suspension architectures. So here, the first setup, this is called a torsion beam or a twist. So this is common in, you know, economy cars, small economy cars. So in this case, it's an Audi A2. So here you can see that the design is relatively simple. So all you have is you have the wheel carrier here, you have the damper and spring. In terms of links, you don't see anything. You just have this big bar here. So this is your twist beam, kind of similar to the anti-rollbar.
So the idea here is, you see this distance here. So when you apply a force, say the wheel here experiences an upward force, it's F. And if this distance is L, the twist beam here experiences a moment of F into L. And so that moment is transferred to the other side. So you get that twisting action. So it's essentially a big roll bar. So then you have bushings on this end for, you know, taking 4F loads, providing 4F compliance, you have bushings here. But yeah, the overall idea here is very simple. And let's cover the multi-link suspensions, the two types of multi-link, and then move to the solid axle.
So here are the first type of the multi-link suspensions. So you remember that earlier in the degrees of freedom and motion path section, we said that we need five pure tension compression links or two force members to provide five degrees of restraint to the suspension. So here you can see all those five links individually. So this setup is made up of five distinct links. So let's go through all the parts. So you have the damper here. So this looks like an air spring. So the RT-Q7. So this is the airbag.
And you have the subframe here. And so all the components are mounted to the subframe. And the subframe is generally, it can be hard mounted, which is bolted, or it can be mounted through bushings to the body. So you can see the subframe mounts. So you have four points here. They are the subframe mounts. And you have the rear differential and the half shafts coming out of them. So now let's move on to identifying the links. So you might not be able to see all the links, but let's try our best.
The upper control arm here, we have two upper links. So this link here. So this is your, let's call this upper link rear. And this, I'll just put a dot on that. So it's this one. So this is the outboard side and this is the subframe side. And the other link is this. So this is your upper link front. So you have your two upper links. So you have to identify five links here. The third link is carrying the spring. So you can see this big black link here.
So that is your lower link, or we can even call it the spring link, because it's carrying the spring. And then here we see a longitudinal link. So that's your second lower link. This is your longitudinal link. So we've identified four links, two lower links and two upper links. The fifth link is to control the steering. So even though there's no steering in the rear, you have to, you know, lock that degree of freedom. So we need a link for that. And so that link is somewhere behind here.
It's very hard to identify. So you can see that there's a link here, you know, running this way. So that's your fifth link. Yeah, it's really hard to see in this picture, but yeah, that's your toe link. So you have five links here, five tension compression links, providing five degrees of restraint. And So this is another type of multi-link suspension. So here instead of five links, we have only four links, but the difference is this is not a tension compression link. This is a trailing arm or a blade. And this can react by bending. So it's not just pure tension and compression.
So this arm here can bend. So it can perform, essentially perform the function of more than one link. And this, so this is connected to the body. So this is your body mount. And again, we have our damper and spring and the subframe. So all this is the same as the five link system. So here we have, so we've identified the arm. So we have three more links here. As I said, there are only four links, not five. So you can see the upper link. So this, we call this the camber link. So it's used to provide camber control.
So we'll look at all that in detail later on. But yeah, this is the camber link. And then the spring is sitting on a link. That's called the spring link. You can see that. But the red spring here is sitting on a link. So that's your spring link. And you have the toe link here. Now the challenge, one of the challenges with this setup is designing this arm is very difficult in terms of durability, you know, strength and durability. So it'll be very careful because that's going to take bending loads. So you have to make sure it can withstand the forces.
And so these were all independent suspensions. So this is a dependent suspension or a solid axle or a rigid axle. So this is common in, you know, heavy duty applications like trucks and even some SUVs. I don't think any SUVs now use this, but this used to be the suspension of choice for all your heavy applications. So here you can see that there is a big beam here running from end to end. So that's your axle. So this beam here. So that's your axle housing or axle beam.
Now inside that you have drive shafts. So you have the diff here, the rear differential, and you have the drive shaft sitting inside this axle and driving the two wheels. Now you have longitudinal links. So these are longitudinal links, and then you have, so this blue link here, that's your lateral link. And you also have a roll bar. So this is your drop link and drop link connects the knuckle to the roll bar. And then we have the spring and damper. I'm not going to name that, but we have that here.
The main difference between the independent systems is connected. You know, the beam connects the left wheel to the right wheel. So any input here is going to be directly transmitted to the other side. But here, if you don't have the roll bar, theoretically, one end is completely independent of the other because there's no link that's running between those two. So in this system, if you hit a bump on one side, your entire axle is going to move around. So that kind of makes it unstable. So moving on to racing suspensions. So those were all commonly road car and sports car suspensions.
So here, so the main difference with the, in the racing suspension architectures is something called the push rod. So in this setup, this is a rear suspension. This is a double wishbone. Again, so this is your lower wishbone and that's your upper wishbone. So that's the same, you know, upper wishbone. You have two ball joints here connecting it to the knuckle, just as in our previous architectures. And then on the inboard, so this is mounted to your chassis. So the main difference here is the push rod.
So this structure that you see here, this link, that's called a push rod. It's called a push rod because of when the suspension goes and compression. So when the wheel moves up, this pushes on this triangular piece here. So that's called a rocker arm or a bell crank. It's called a rocker or a more common name is bell crank. So this rod pushes on the bell crank and that in turn pivots about this point. So this entire truck. It pivots about this point and it actuates the spring and damper assembly.
So that's your main difference. Usually your spring is carried by the suspension links, but in this case, it's mounted more inboard and it's actuated by the push rod. So here you can see this is an actual Formula 1 car. So the front suspension here, you can see the, so this is your upper control arm. Or upper wishbone. I'm just using the terms control arm and wishbone interchangeably. So then this is your lower control arm, LCA. And this would be your steering or tie rod. So that steers the wheels. And this is your push rod here.
So this is the push rod. So that actuates the bell crank, which in turn pushes the spring and damper. So you can see that the spring and damper are mounted far away from the wheel. So it's mounted on the body structure here. So that's the main difference between regular double wishbones and push rod. Now the main advantage of this is that if you look at the picture, if you look at this CFD simulation picture here, it clears the path for the airstream. So here in the front suspension. So this is where your damper would be.
If it were a regular wishbone, this is where your spring and damper would sit. And that's going to affect the airstream. So the airstream won't be clean. So for aerodynamic purposes, so in this case, your spring and damper is sitting somewhere here. So it's because of that push rod. If you mount that here, this area becomes very clean. So it gives you a good airstream and improved aerodynamics. So that's one of the main reasons we push the spring and damper inboard. So these are some common suspension architectures.
Now, so there's some activities that you need to do. So I want you to provide a brief comparison between dependent and independent suspension systems here. Solid axle and the independent systems. And after that, provide some advantages and disadvantages. And just come up with some, just it can be brief, some four or five points between double wishbone and McPherson front suspensions. And again, repeat the same thing for any two independent rear suspension architectures. So the goal here is to do some research on your own. Just go through some production car suspension setups.
Just study the different advantages, disadvantages. It's OK if you do not completely understand the behavior. So just try to understand. Just provide a write-up because this is what we're going to be learning eventually. We're going to learn all the different suspension parameters. And towards the end of the course, we'll revisit this. When we study the topology suspension architectures of production vehicles in that section, we'll come back to this. And we'll discuss the advantages and disadvantages. So after we complete the course, after we learn all the suspension parameters, it will make more sense to you.
But I'd really like you guys to do some research and just answer these questions.