Unlock all 34 lessons of Suspension Design using ADAMSFull course ₹40,000 · paid
Degrees of Freedom and Motion Path of a Suspension
A free lesson from Skill-Lync's Suspension Design using ADAMS course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “DOF and motion path and questions”
What will you learn in this free Suspension Design using ADAMS lesson?
The instructor explains that an independent suspension has six possible degrees of freedom but is designed to leave only one, so the knuckle follows a single path. The lesson compares this with a solid axle and shows how five two-force links give five restraints, then sets three review questions.
- Six degrees of freedom: three translations, three rotations
- Independent suspension has one degree of freedom
- Solid axle has two degrees of freedom
- Five two-force links give five restraints
What comes after lesson 1?
The next free lesson is lesson 2, “Why Suspensions Exist and Common Suspension Architectures” (23 min). Later in Skill-Lync's Suspension Design using ADAMS course (paid): lesson 4, Camber gradient seg 1; lesson 5, Camber gradient seg 2; lesson 6, RCH Scrub. The full course has 34 lessons (13 h 48 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Before we go into suspension geometry, before we learn anything about suspension kinematics, we have to understand the concepts of degrees of freedom and suspension motion path. So if you look at the first point, for an independent suspension, the wheel motion relative to the body follows a single prescribed path. So there may be changes in camber, caster, toe as the suspension goes in compression or rebound, but it still follows only one path. So it cannot move fore-aft or lateral or it cannot rotate about this path. So if you look at the picture here, the degrees of freedom.
So here we see six degrees of freedom, three translations and three rotations. Now we design the suspension so that the links provide five degrees of restraint or in other words, they provide only one degrees of freedom. So the knuckle here has only one distinct motion, one path or one degree of freedom. So we're still talking about independent suspensions. We'll come to solid axles in a minute. So independent suspension has only one distinct path as the suspension moves in Jones or rebound. So the links constrain it in other five directions that cannot move relative to this path.
So the study of independent suspension geometries, this whole thing we're going to do here, is to determine how to control the knuckle or how to restrain the knuckle to limited motion in five directions. So here I say limited motion, I don't say no motion because there are bushings. So there is some compliance and it's not completely rigid. So there is some compliance in the other five directions. So this is, you see the motion path here for the independent suspension. So for the solid axle, there are two degrees of freedom.
So if you look at this axis here, so the solid axle can move about this axis. So that's your Jones axis. And the other degree of freedom is the roll axis. So the solid axle can roll about this axis. So here we have four degrees of restraint or two degrees of freedom. And this picture here, the number of links required to provide a certain number of degrees of restraint. So if we have simple two force members, by two force member, I mean a tension compression link, then we need five links to provide five degrees of restraint.
So for example, in your double wishbone suspension, you have two A-arms and then you have one tie rod. So the one A-arm is considered as two links. And the second A-arm, you have another two links. So there are four links. And then the tie rod controls the steering. That is the fifth link. So these five links together, they provide five degrees of restraint. Now, this is true only if all these links are two force members, only if they are tension compression members. If not, sometimes links or arms can react to bending forces as well.
So they can provide resistance to bending or torsion. In that case, you don't really need five links to provide five degrees of restraint. So, yeah, that's the concept here. So we looked at degrees of freedom. We looked at how many degrees of freedom or restraint an independent suspension or a solid axle has and how many links we need to provide a certain number of degrees of restraint. So these are the questions for this section. So the first question is just define degree of freedom in your own words.
You can use any resource. Just define what degree of freedom is. And second, how many degrees of restraint does a ball joint provide? So just, you know, it's a one word answer. And the third question is in a suspension, are five links absolutely necessary to provide five degrees of restraint? So please answer these questions.