Unlock all 66 lessons of Structural Stability of Lateral ForcesFull course ₹40,000 · paid
Stable and Unstable Equilibrium and Global Instability Modes
A free lesson from Skill-Lync's Structural Stability of Lateral Forces course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Stability in Static Systems”
What will you learn in this free Structural Stability of Lateral Forces lesson?
The lesson defines stability through the six degrees of freedom of a point, the bifurcation point and the rolling ball analogy. It then shows how a diagonal element stabilises a pinned frame and lists global instabilities: overturning, sliding, racking sway, twisting and snap-through.
- Six degrees of freedom and equilibrium of a point
- Rolling ball analogy for stability
- Stabilising a pinned frame with a diagonal
- Overturning, sliding, sway, twist and snap-through
What comes after lesson 2?
The next free lesson is lesson 3, “Buckling Modes and Frame Stability Under Lateral Loads” (20 min). Later in Skill-Lync's Structural Stability of Lateral Forces course (paid): lesson 4, Introduction to Frame Behavior Under Lateral Loads; lesson 5, Structural Stability for Lateral Forces; lesson 6, Construction Phase Loadings and Structural Considerations. The full course has 66 lessons (17 h 43 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
I'm going to continue from where I left off in part one. So now we are going to talk about the definition of stability. Any point node in a static system has six degrees of freedom, three translational as well as three rotational. The actions acting on a point in space must be equal to its reactions concerning all of its six degrees of freedom for the point to be considered stable. Point must be in equilibrium for it to be stable. An unstable point does not return back to its original position after a small perturbation, small movement. So if there is a point in space and you pushed it with your finger, if it return back to its original position after the force that have been applied to it have been removed, then the point can be considered stable.
Otherwise, it is categorized as unstable. Otherwise, it is categorized as an unstable point. In mathematical terms, the transition phase of a point from stable to unstable equilibrium is referred to as bifurcation singular point. Further perturbations, i.e. increase in load to push the point, from this state will cause instability. At the bifurcation state, the applied load is less than or equal to the needed value to maintain equilibrium. So the bifurcation point is the point at which if you increase the applied load a little bit more, the point will become unstable.
This is what we mean by bifurcation point. Assessing the response character of a static structure is referred to as structural stability or instability. So if we look at the figures on the right-hand side, the first one on the top demonstrates a point in space that has six degrees of freedom. Three translational, these are x1, z1, and y1, and three rotational, these are rx, ry, and rz. The figure on the left-hand side is basically a point at the bottom of a ball. And when you push it, i.e. you do small perturbation, it will move up to the right or up to the left, and then it will return back to its position.
This is considered to be a stable point. The one in the middle represents a point on the top of the ball. If you do small perturbation to it, to the left or to the right, the point will fall from its location down, and therefore it is considered to be an unstable point. The figure on the right-hand side, the figure on the right-hand side shows a point at its bifurcation state, so it is stable. If you just do a small movement, it will fall off and considered to be an unstable point.
Rolling ball analogy. So this is what we use to explain in simple terms what do we mean by a stable and unstable position. So you can see different positions on the figure on the right-hand side, a, b, and c. So the multiple character of static equilibrium positions are demonstrated in the figure on the right-hand side. The surface in the static system has a curvature equal to zero, normal to the plane of the figure. The ball that we are assessing has a weight equal to w. It rests at multiple positions with a zero slope on the surface a, b, and c.
So let's study it in more detail. So at point a, the ball is subjected to small movement or perturbation. It will simply oscillate about its static equilibrium position. So it will move up to the right, up to the left, and then return back to its original position. This position is referred to as a stable position. If we study point b, small movement will cause the ball to move away from its initial static equilibrium position. Therefore, this position is referred to as an unstable position. If we look at point c, the ball will maintain its disturbed position when subjected to a small movement.
So if you do small perturbation, it will keep on moving. I.e. it does not go back to its initial equilibrium position when the force applied have been removed. Thus, this position is referred to as neutrally stable or indifferent in the small. Disturbed position is one whereby the ball does not go back to its initial equilibrium position, neither continuing to move away upon the removal of the disturbing force. So equilibrium, in a mathematical sense, is basically equations for the determination of a system, element critical load, i.e. load that will cause instability, can be derived using numerous mathematical methods such as equilibrium approach, also referred to as bifurcation approach, kinetic or dynamic approach, potential energy approach, also known as energy method, imperfection method.
So these are the various mathematical models that are used to assess the stability of a structure. Now we're going to talk more about stable structures. What are stable structures? A stable building is defined as one which, when subjected to actions, either in its construction phase or during its use, will not. Number one, fully or partially collapse, experience unacceptable deformation levels, break its cladding, fittings, finishings, and other non-structural elements, lead to disproportionate damage in relation to its original case under an event. For a structure to be considered stable, it should return to its equilibrium position following a small movement.
This is similar to the rolling ball analogy that we spoke about previously, at position A. So basically when you apply a small force to a structure, it will oscillate back and forth. Upon the removal of the load, the structure will go back to its original position. This is considered to be a stable structure. A structure is considered to have a stable movement if minor changes to its original conditions lead to insignificant changes in its response. This is particularly important when a structure is subjected to a non-conservative loads that are path-dependent.
Thus, starting and ending positions of a structure are of importance. To understand this, a good example is a pendulum. So a pendulum, if you hold it in your hand, hanged in the air, it's at its initial position. If you apply a horizontal load, the pendulum will oscillate back and forth, and then due to damping effect, eventually the pendulum will go back to its original position. This is what we mean by a stable structure. Pendulum is a good example of a stable system. It will return back to its initial position after oscillating back and forth due to an applied load.
A stable structure should be designed to successfully resist lateral movements that might be the result of wind loads, seismic loads, unbalanced loading, geometric imperfections, etc. So the figure on the right-hand side demonstrates the pendulum that I just mentioned. And structural lateral stability must be ensured in both orthogonal directions for all relevant load cases. So structural engineer must ensure that stability exists in a structure in all of its direction. So if it's a square shape on plan, stability should exist in the x and y direction. and all the various load cases should be assessed and the structure should satisfy all of them for it to be considered stable.
Instability in structure is a strength-related limit state. The structure on the right-hand side demonstrates an unstable mechanism as all of us know. Four nodes are pinned. So if we study the figure on the right-hand side, we can see that the connection at the bottom of the columns are pinned. The connection between the columns and the beams are pinned. Therefore, if you apply a lateral force of magnitude P, your structure will sway or move away, and it will not go back to its original position. This is considered to be an unstable structure. This in turn causes acceleration of the frame away from its position of equilibrium when subjected to the applied load P.
In order to make the previous structure stable, we can simply introduce a diagonal element. This diagonal element will act in tension when we apply the force P, the lateral force P, and therefore it will prevent the structure from moving away too much from its original position, and this is how we make the structure stable. These are referred to as bracings in practical cases. So the structure shown has been stabilized by introducing a tie element that will act in tension when subjected to the lateral applied load P.
Thus, the frame will accelerate back to its initial equilibrium position upon the removal of applied load P. Next, we are going to talk about forms of structural instabilities. So what are the various forms of instabilities that can occur in a structure? Instabilities in structures fall into two main categories. The first one being global instability, so this is the overall failure of the structure. The second one is local instability, so this is at individual elements level. A stable structure needs to be checked against both global as well as local instabilities during its construction phase as well as throughout its life cycle.
Lateral instabilities in structures arise mainly due to the fact that vertical loads are no longer acting concentrically to the centroid of the members. More the slenderness of the structure, more the structure is susceptible to instability problems. So basically this is saying the taller the individual element or the structure becomes, the more susceptible it becomes to instability problems. And therefore the more carefully the structural engineer needs to assess the structure for stability. Global instabilities. So what are global instabilities? They occur at a subframe or the whole structure level.
Examples of global instabilities are overturning, sliding, racking, i.e. sway and twisting are the examples of global instabilities in structures. Overturning stability is ensured by checking that the sum of the total destabilizing moments are less than or equal to the sum of all stabilizing moments. So this is how a structural engineers ensure that overturning instability will not occur in the structure that they are assessing. Foundation failures such as buoyancy, i.e. uplift and slope failures can lead to overturning instability. Racking, sliding and twisting are forms of lateral instability modes.
Another form of global instability is snap-through, which is a type of buckling instability where a sudden and visible shift occurs from one equilibrium position to the next. Snap-through instability is prevalent in flat arches or shallow shells. As the compressive forces acting on a member increases, its stiffness partially in bending reduces. So if you have a vertical element, i.e. a column, the more axial force the column experiences, the less its bending resistance is going to be until a point which is referred to as a critical load when the column will become unstable and it will buckle.
If the stiffness reduction is significant, then loss of structural instability occurs. Once a loss of structural instability happens, primarily large displacements occur followed by secondary plastic deformations, and hence the element becomes unstable. Consequently, full or partial collapse of the structure takes place. These figures illustrate the global instability modes that we just spoke about that can occur in structure and which structural engineers need to assess carefully and make sure that they will not happen in the structure that they designed. So overturning, basically, we need to check that the sum of the overturning moment are less than the sum of the counteracting moments.
Racking sway, so you need to make sure that it will not experience significant horizontal displacement. Sliding is basically, you need to make sure that there is sufficient grip or friction between the bottom of your structure and the foundation for sliding not to occur. Twisting, this is involved with how the lateral stability system is distributed on plan. If it is distributed in a symmetrical manner, then twisting global instability will not occur. And then you can see the sway and twist. So twist is more or less associated with torgen.
Sway is basically due to excessive horizontal deflections. And the last two figures on the right-hand side demonstrate snap-through buckling. So in an arch, due to its arch shape, if it's experienced significant vertical loads, it will all of a sudden move from one position to the next. And this is what we refer to as snap-through buckling. And that's what we refer to as snap-through buckling.