Lesson finished
Unlock all 59 lessons of Roadway Design with OpenRoadsFull course ₹40,000 · paid
Horizontal and Vertical Alignment Design Elements Explained
A free lesson from Skill-Lync's Roadway Design with OpenRoads course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 3”
What will you learn in this free Roadway Design with OpenRoads lesson?
The instructor gives a theory overview of horizontal alignment, vertical alignment, super elevation and sight distance, linking each to design speed. Guidelines for tangents, simple and compound curves and broken-back curves are covered, followed by a map example of a bypass alignment weighing environment, community and cost.
- Tangents, simple, spiral and compound curves
- Super elevation as banking against lateral acceleration
- Guidelines for flatter and sharper curve radii
- Alignment impact on environment, community and cost
What comes after lesson 3?
Later in Skill-Lync's Roadway Design with OpenRoads course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 59 lessons (26 h 54 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello and welcome to the roadway design with using open roads. We are in week number one roadway design with fundamentals and let's go to the next chapter where we are learning the design elements. So till now we have seen the design summary report, the typical sections about the fundamentals and the project workflows and the workflow overall in the projects. All right, so in the design elements, these are the few important aspects and from theoretical conditions, I'll be explaining you over here a few of them. We'll be looking into detail for sure in the software, what exactly, how we are going to lay these things, how we are going to design and model this, but just before a brief theoretical understanding about each of these.
So talking about horizontal alignment, to achieve balance in any highway design, all the geometric elements should be as far as economically practical for designing to operator speed likely to be observed under the normal conditions for that roadway and for the vast different kinds of vehicles or motorists basically. This can be generally achieved through the use of design speed when we are talking about design speed from our design summary report, we have finalized, we are phrased that in the planning and schematic phase, which is overall design control.
So on the basis of that, basically, we can move forward to layout or layout of the design features for horizontal element. So the design of road curve should be based on the appropriate relationship between the design speed and the curvature and on their joint relationships with the super elevation, which I've mentioned in my third bullet. And super elevation is something as a roadway banking, where we elevate, we bank one side over the other, and of course, the side friction. So these are something important aspects related to the horizontal alignment are talking about vertical alignment.
It is depending upon the topography of the land, which is traversed as an influence on the alignment for the roads, topography affects horizontal alignment, but has a more pronounced effect, basically, on the vertical alignments. And to characterize the topography, we have seen before in the terrain classification, which is typically called as level rolling and mountainous, depending upon the percent of slope within the range of 0 to 10, 10 to 25, 25, and so on. So the important aspect in vertical alignment is the grades. So highway should be designed to encourage uniform operations everywhere throughout the alignment.
So as discussed before about the design speeds are used as a mean for correlation between the geometric features of the roads. So design corrects have been determined for many highway features and the relationship between the roadway grades to the design speed, which links basically to generate the grades. When we say grades, it is either negative or positive grade, like uphill or downhill, basically. We will see that in our next slides as well. And talking about super elevation, it is basically banking, as I mentioned just before.
And it's in the terminology of mechanics, laws of mechanics, basically, where the vehicle moving in a circular path, it undergoes a centripetal acceleration that acts towards the center of the curvature. So this acceleration sustained by a component of the vehicle's weight, which is related to the roadway super elevation and side friction developed between the vehicle tires and the pavement surface or both the combination basically like the centripetal force acting inside, as well as the weight, as well as the weight, which is acting downwards and the friction between the tires and the pavement.
So this all combination centripetal acceleration is sometimes equated to the centrifugal force. We have done in physics in our 11th, 12th done exercises also with that. What exactly centrifugal force with that in the practicals, basically. So to act, to counteract this basically, to counteract for this on the horizontal in the curve design of the centripetal acceleration, the lateral acceleration, super relation comes into picture. So there is empirical formulas for that in every manual in AASHTO, IRC. Nothing changes much with some factors and local conditions which have been mentioned.
Site distance is also an important aspect when there is a major street and a minor street or any intersection basically. And the category of both the roads, so one is a major arterial, second is a urban street or second is a driveway and one is a driveway is coming to the major street. So depending upon that, the relationship of these two cutting roads, side distance plays a very important role. Preference is given, of course, to the major road because it's having a higher speed and there must be more the category of the roadway, greater must be the length of side distance.
So that for safety point of view, a vehicle can stop, see and then surpass that road, cross that road. And there are also other features in design elements and not just these, but just a few, some of the important ones. All right. So moving on, talking about alignment in detail. So horizontal alignment or vertical alignment, when we say it's actually an imaginary line which joins between two destinations. Okay, I will just see here two destinations. It can be, you know, multiple destinations or point A to point B as well.
We really, we design it on paper with geographical coordinate system exactly imagining from one point to another point. So, but it is really doesn't, is there on, while we construct it, we stake out the alignment very first. So, so talking about it, it's an imaginary line joining two points and the alignment consists of number of design elements, which, which are combined together. Like horizontal, there are tangents, there can be transitions, there can be simple curves, there can be spiral curves, there can be back to back curves, S curve, compound curve.
So these all elements, these are design elements together combinedly form an alignment. Okay, okay, why having, having just the one tangent line joining one, so that doesn't fit in the design standard. There are also certain restrictions for how much straight tangent length can be. Okay, so that's why introduction of horizontal curves is also necessary. The elements in the alignment should complement each other to make the design consistent, safe and efficient. This is important because when we, when we design the alignment, one must not just consider from the point of view of that road, but with consistency with the neighboring site, which is where we are designing the road, it must be safe, safe with all the design criteria.
So what we are going to see in the horizontal alignment and vertical alignment, it must be efficient. So though mentioning it the last point, but efficiency is from point of view of the cost as well, and its life as well. So, and also some criteria has come into picture when, and it is related to the government agencies and the planning agencies, how the fund is getting created. So the construction period, the traffic phasing period, the temporary traffic, which is being phased out while constructing. So all that thing, so all that thing from starting till the design life of the highway, so that's also comes under efficiency.
So that's a very important aspect to be taken care of. Roadway alignment has a great impact on the environment. So when we are planning a road through, it goes through multiple environmental or nature, natural conditions, basically, there can be natural lakes, rivers, forests, some reserve lands, some swamps, or any kind of these environmental natural things which are there, which we don't want to disturb, which we don't want to create a major impact or a major change to that environment is also very important in many of, in almost every, every manual, basically, every country, every city is having its, how to protect the environment, basically.
We can't just lay out alignment. Okay, absolutely there is a purpose for the roadway. It is, it does helps in improving the infrastructure and indirectly supports the economy of any country and cities. But that aspect of environment has also great impact. The next is the fabric of the community. From wherever the roadway is going, the street, the areas, it may be the urban areas, it may be the rural areas. So we are designing a completely green field projects or brown field projects. And we are changing the fabric of the community. That must be taken care while it is being done.
Also the highway user. So who is exactly going to use the highways, that consideration must also be given to it. So to give an example, like there can be just fright corridors. There can be just dedicated to fright. So there will be a huge traffic of all the trailers and trucks and heavy loaded traffic. So the highway user, the user is completely different in these cases. So that is also having an impact specifically. When there is a mixed use, there has to be a taken of mixed use impact of highway users.
When there is just passenger vehicle or that use with has to be taken care of. If there is a cycle we added with that, that user impact creates on the roadway alignment as well. All these conditions, all these criterias do play a major role. So proper relation, as I mentioned before as well, between the design speed and curvature is necessary in the highway alignment design. That goes always hand in hand. So once the design speed is fixed and we have to design our alignment, that's why it comes in a very earlier stage.
What is the category of the road? What is the design speed? What we are defining for this category of road? Once that is freezed, all the necessary design which goes in the background before we construct it, it all goes hand in hand. So proper relationship between design speed is very important because with this we also consider what is the design vehicle for that. So I have not mentioned that point in the slide here, but design vehicle are different kind of design vehicle which plays a role.
There can be passenger car vehicles, there can be semi trailer, there can be bus and there can be huge trailer. So all depending upon these design vehicles, which is also again linked to the alignment design. So basic elements of horizontal alignment is the curve where we give the tangents and the curve radius. So curve radius the length of the curve horizontal curve is important. Also the transition which comes in aspect of super elevation design as well as in the geometry design. It is clubbed up together. The super elevation rate which helps to define the roadway banking.
That is also very important. And there can be different rates at which super elevation banking can be limited to. So there are graphs in IRC, in AASHTO and other codes as well. What Emax one has to use basically. We will speak about super elevation in literacy as well. So general considerations talking about horizontal alignment, it has to be safe. Of course, it has to be smooth or you cannot have, you know, extremely undulated and unpleasant alignment basically. It must be aesthetically pleasing facilities as well. As much as flatter curves on the alignment are preferred.
If you don't have the enough right of way, if land has not been acquired and then there is no option for that, then yes, sure. We have to give less flatter curves or in worst case, it can be tight curves. I would always say like, you know, and even in mentioning the codes as well, the caution to use in compound curves. Compound curves is a curve immediately with a smaller tangent or without a tangent direct curve with two different radiuses back to back. And instead of having that one can try to introducing instead of two different compound curves, basically to introduce one simple curve, which helps in super elevation design and passing through the highway alignment on that stretch.
Which basically becomes easy, smooth and the consideration what we have considered safe, smooth and aesthetically pleasing facilities. So specifically avoid the compound curves in front of flat simple curves. Yes, absolutely. That is something very important. Some more general considerations. If used, the radius of flatter curve should be less than 50% of the radius of sharper curve. That's a thumb rule, I would say. And for intersections or other turning roadways, it can be increased to 100% because that's the different category or where we are, you know, coming across a different scenario.
That's why consistency in the alignment. So that's also important. Sharp curve should not follow tangent or a series of flat curves and avoiding sharp curves in high and long field areas. That is also one of the important aspect to be taken into account while designing the horizontal line. Which few more talking about the general considerations include intervening tangents at reverse curves on high speed facilities. Yes, that is absolutely necessary. And whenever there are, there is a S curve and a tangent must be provided as far as possible.
And I would say not at a minimum level, but to the maximum values, whichever are there. Broken back curve should not be used. Yes, as I just mentioned, broken back curves are not good and pleasing for the driver to over the is maneuver his car through. Our design speed should be considered consistent with the design features and topography. So sometimes basically what we come across is we cannot give the constant design speed or basically in other way around talking about it is this. We cannot achieve a horizontal curvature radius basically in some parts.
So due to it, we change the design speed conditions in specific parts and regions. So and also the topography. So there might be a topography, which is very after some plane or rolling there in that there might be a possibility of a hilly terrain. So in that hilly terrain, we either the cost constraint will be there or maybe some other constraints can also be there. Typically, the cost constraint constraint come from if a plane or rolling terrain comes and merges with a hilly terrain because there is possibility of adding in more structures like wire ducts and those kind of things.
And whenever you want to that's why I mentioned like whenever you want to have to be cut, but cost also plays very important role while doing it depend upon which category and where you are doing this roadway alignment. All right. So moving on. So this is just a simple diagrammatic representation captured from Google giving credits them on here where you see there is a point a called as Darward. That's one city in Karnataka Street in India and one over Hubli basically and this stretch, which is having the yellow line, which existing roadway, which is shown over here.
And as you see, it's not a straight line over here. OK, we don't see the terrain actually in this in this view. Basically, what we see is basically, OK, in the circular form, the city has been formed. There is a community. And as you see, there is all farmland typically seen along the highway, basically. And this point, even the Darward point, what we see over here is a people staying in that or, you know, the community has been established over here. But as this road has been formed after, so when we call it outskirts of a city.
So typically there is nothing in this area and then along the road, there is some development. So when we also develop our or design our options, basically, it also helps in other businesses and to connect that infrastructure point of view. And these lines, which also showing with the red and the green color, shown as a highway realignment at some portion or can be a new alignment, basically, which has to be developed, basically can be planned in the schematic phases. So as you see in this area specifically, the existing road now having a community, which I described over here with the village or the city has been established or here.
But in this area, there are no, none of them are there. If we talk about this green alignment, it's passing through some of the farmlands over here. We see some water body can be a dam or, you know, any kind of water body. So it's impact. So need to consider how it is going to impact it. We see some important structures in this area. So how it's going to affect that. We see this road which is given as option going through the existing road to this portion and this road is a new alignment. Now multiple locations there will be required to acquire the proposed right of way to buy land for building this public road. So that's an important aspect towards looking at it.
Also one thing has to be taken care and given more importance as well. You see that the existing alignment which is coming and we are proposing a new bypass. So the smooth transition of the new link has to be established and the addition of the traffic must not cause bottlenecks. So accordingly there must be enough room space available in this area. Basically these nodes or the joints or I'll call it bottleneck possibly which one must also take into consideration while designing this alignment in these locations.
The curves which are seen in this area are just representative and of course means you cannot have all three of them but these are the options. So one of those can be showing in just one pictorial view. Also what it tells us this image in designing our horizontal alignment is that where you are going to tie in at an intersection what all proposed developments do we need to do with that over here. And also how it is going to help the existing highway user which was from point A to point B and the addition of new alignment how it is going to impact on the highway user how it is going to impact on the fabric of this community over here how it is going to impact on the environment over here.
How it is cost effective and efficient basically. So these points are very important when we design or layout our alignment basically and also while this these are the phases which will come while doing your alignment at the very planning phase or also while doing your detailed design and suggesting any new suggestions which are required to be given to the authority when you are doing that. All right. So this just was a pictorial presentation and these are the options basically I just mentioned and the example cases will be different in the projects what you will be doing but just theoretical point of consideration basically are also important.
Maybe I just a few missed which we don't see really here but we will be looking at those in the next upcoming images. All right. So a few of the images basically taken from some references you will find like these are some typical images but what as a engineer what as a highway designer what you have to look at these is basically. Okay. Okay. You see a simple single lane road I would say looking at the striping even we have flat slopes in this area. Okay. So we have some utilities we have some overhead electric poles. So from safety point of view for these structures what care has been taken that is important in this thing to be considered.
What is the slope or what is the slope or what is the cross slope being given we can just visually see those criteria are important and the second one we can see about it is maybe going through a reserved forest land or maybe through some. environmental conditions where a lot of forest kind of thing is there and need to be taken care about it's what new change we are introducing it it's not impacting the environment in this condition. How much cut and fill we are doing which is minimizing also the soil erosion needs to be taken into point.
So not just when you are designing or I mean you have to think of your pavement and and and and just about the road but also about other things. counselors and horizontal curves given in this location which you see depending upon the contours and the terrains available in these kind of political conditions as well. The third picture over here down below. I see that looking in the image kind of a first of all a hilly terrain looking at the clouds and some. rocky mountain kind of thing but it's forming a road kind of a either roundabout so for vehicles to now maneuver in a specific way and not to have a sharp curves basically it's it's a two lane basically with back-to-back curves as you see so is a tangent provided is island kind of thing provided with a striping on the pavement marking given over here and throughout entirely on the outer side of both the edges basically you see the roadside safety measures have been taken and these kinds are important also one can see over here is that the visual effect for our driver basically is going to get reduced due to the this climate what the picture is taken maybe so the speed criteria and some more reflectors or some safety point of view which because the visibility is going to go less in in that curve area so that's a very important aspect in in these conditions and also to be point to be taken in in such conditions there will be also rainy seasons possibility of very heavy rains typically in these kind of areas so drainage is one perspective and visibility and the friction with the tires it's one perspective so all these considerations which one will see is how it is important with the alignment yes it is important with your alignment design moving on to the last pick it's a hilly mountainous terrain with a horseshoe kind of shape or a u-pin bend basically yeah with a pavement marking you cannot so it's a yellow double stripping you cannot overtake in that area basically possibly throughout over here it's a just undivided possibly a two-sided roadway important aspect is basically it's it's going to a rocky mountain areas the hill slopes the cutting slopes which are being done what's the angle basically is being taken what are the criteria's what what have you taken care for the soil erosion in this area basically and specifically talking about our design vehicle which like trucks or trailers which will maneuver through here in some breakdown conditions can they do they have some space available so that they can pull out their vehicle from away from the highway basically and the remaining cars can still continue with the smooth traffic basically so these kind of things are important environmental impact is also surely one thing as you see the geometry basically looks like typically this is a compound curves with multiple radius being provided and our roadside safety the crash barriers have been provided on the outer side towards the valley side also some extra space has been given given on specifically the tight side of the outside outer side of the curve typically the driver's movement of its outer wheels of of his car basically or or its design vehicle goes off the edge of pavement so those things have to be taken care and so these are the important aspects when you design your alignment alignment all right so moving on so this shows a plan and profile and for sure we are going to cover this in detail in our plan production at the end but talking about it in brief over here is that when we do design our alignment when we design our site and layout this is a drawing which or finally you are going to design do some engineering to modeling and uh it needs to go on a piece of paper because those drawings looking at that has to be built finally so when the when the project is designed uh the tender drawings will be uh published and the contractor or who is going to build that will will develop uh looking at these plans so what does a plan and profile is showing over here is is showing the proposed and existing rate of ways with the dotted line it's showing the match lines of of a specific portion of a roadway showing a north arrow where is the true north of The river which is going in this area in the same view basically this is a plan view where it's aligned with the profile view and if you align the river to this area in the profile you see the flow path of the existing ground of the river as well and the continuing existing ground of this topography so the PGL or the proposed grade line which is designed in this area is seen in red which are being called out and the grid which shows horizontally the stations and vertically the elevation basically and it's the profile view is cut in two different views because it's a rolling terrain and this is going this all is flowing downwards to the river looking at this alignment it's on the horizontal curve possibly with the super elevation required and there is a for sure requirement of a bridge in this location creek or creek bridge crossing or river bridge crossing the span will be decided depending on your alignment which is designed so when you freeze your alignment the bridge is going to be dependent upon your horizontal curve your super elevation transitions and that design so So this covers most of about the horizontal alignment and we'll carry on in our next video about the other aspects of it