← Previous lessonFree lesson 3 of 3 · lesson 3 of 69

Unlock all 69 lessons of Reinforced Cement Concrete DesignFull course ₹40,000 · paid

Price & syllabus
Free lesson · 40 min · no payment

Characteristic Strength, Confined Concrete, Creep and Shrinkage

A free lesson from Skill-Lync's Reinforced Cement Concrete Design course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 3”

What will you learn in this free Reinforced Cement Concrete Design lesson?

The instructor explains characteristic strength as the five percentile strength of a concrete mix, and how quality control changes the spread of test results. It also covers confined concrete, tensile strength through the modulus of rupture and split cylinder tests, and a worked creep example for M30 concrete.

  • Characteristic strength as five percentile value
  • Confinement raising strength and ductility
  • Modulus of rupture and split cylinder test
  • Creep strain and effective modulus

What comes after lesson 3?

Later in Skill-Lync's Reinforced Cement Concrete Design course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 69 lessons (31 h 42 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello and welcome back to the course on Reinforced Cement Concrete Design. This is the week one of this course and where we will be going through the introduction, the basics of Reinforced Cement Concrete Design. So and this is the third session of the course. Until now we have discussed in the last two sessions what are the different objectives of structural design. We have seen the serviceability, strength and stability are the three major objectives for which a structural design should be done. Then we looked into different types of structural systems like buildings, water tanks and how the force flow takes place in the structural system.

And then we looked at the different types of what's the purpose of design codes, the different types of design codes across the world. And then the design codes and design aids that's usually used Reinforced Concrete Design across in India. What are the codes that are being used? And then we briefly looked at what's how do we characterize the properties of concrete? So by that we looked into what is the compressive strength of concrete? What is the uniaxial compressive strength of concrete? And then we looked at the stress strain curve for uniaxial compression of concrete.

All this in this session, we will look into the look into what is what do we mean by the characteristic strength of concrete? And then we will talk about what is the confined strength of concrete? So let's get started. As we discussed last time that when we while defining the compressive strength of concrete, we cast a sample from a concrete mix that that specimen sample is cube in India and cylinder in countries like USA and Europe. So whatever be the specimen, you just test that specimen under uniaxial compression in a universal testing machine or some kind of machine.

And then you note down the strength at which the specimen fails. So that's how you do the uniaxial compressive strength of concrete number of the compressive. So on this on y axis, you have number of tests or number of samples that were tested. So basically this figure in this figure, what you see is 176 specimens or 176 standard specimen of concrete from the same batch were casted, were cast. And then they were tested under uniaxial compression. OK, so 176 samples prepare a concrete mix you and then you cast 176 samples standard samples.

And then you do the perform the compressive test, compressive strength test on that. And then you record that what is the compressive strength of each sample. OK, so and then you plot. So what do you plot? So basically what you see over here is like that say around this is say six, six samples had compressive strength between 2000 psi pounds per square inch and 2250 pounds per square inch. So six samples had that then say this is approximately seven. So seven samples had the compressive strength of more than 2250 psi and less than say around 2700 psi and so on so forth.

So if you go to the mean, mean of the curve is 3940 psi. So basically approximately say 28 samples, if you can just, you know, follow this line over here. So just over here, say so we can say roughly that 28 samples had the compressive strength of 3940 psi. So where I am getting at is if you connect the lines, I mean, if you connect the mean of compressive strengths, so you will see that it loosely follows very basically follows a normal distribution curve. OK, if you would have viewed, you would have tested more samples.

So instead of 176, say there, the test would have been conducted on, say, thousand samples. Then this this these solid lines would more closely follow the this dashed line. The more the number of samples, more closely it will follow the normal distribution. So the purpose of showing this graph is just to tell you guys that the compressive strength of a concrete batch or a concrete mix loosely follows the normal distribution or Gaussian distribution. So now based on Gaussian distribution on the normal distribution, we get to the definition of characteristic strength of a concrete.

So the characteristic strength of a concrete mix is defined as the five percentile strength of that mix. So what do we mean by that? So we mean that if say you test certain samples and and less than five percent of all the samples tested will have will have that strength, will have a strength FCK and that strength FCK is called as characteristic strength. For example, if you prepare a concrete mix and you say that my concrete mix is M20 or the characteristic strength of this concrete is 20 megapascal.

So by five percentile, what do we mean is that if you cast 100 cubes from that concrete batch? Now, no more than five cubes, no more than five cubes should have compressive strength of less than 20 MPA 95 cubes. That means 95 cubes will have compressive strength of more than 20 MPA. It can be 25 MPA, it can be 30 MPA, it can be 40 MPA, but it should be more than 20 MPA. So that's what you mean by the characteristic strength that is not more than five percent of the sample shall have less than the characteristic characteristic strength value for a given concrete mix.

Also, the compressive strength of a concrete mix, it shows variability based on the quality control of the batch. So, so let's see that when you mix concrete, when you prepare concrete out of its constituent elements, that is cement, sand, coarse aggregate and water. So you can do it, it's either done in batching plant or basically a factory or you can do it on site. But as you know that on site, it's very difficult to do quality control because you might not have all the machinery or you might have some limited machinery and then the temperature cannot be controlled properly because it's out in the open or you might have a shed or something.

But at factory, you can have whatever conditions you would like to have. So, so, so, so based on that, you will, the compressive strength of concrete does vary based on where you are casting your concrete either it's either in plant or in site. So that's called quality control. Okay, so quality control is like, so by this logic, the factory, if you, if you cast concrete in plant, the quality control is better over there. However, if you cast concrete on site, quality control is not that good.

So we will see how the concrete mix shows variability in its strength in the next slide, this slide over here. It shows basically how the concrete mix, how the strength of a concrete mix varies depending upon the quality control. So this is, so this is, so you can see three curves over here. So, so this say, say, suppose if this is the mean strength, so mean strength means 50% of the specimens that will be tested, that was tested for the given concrete specimen will have this strength.

So now if it's a good quality concrete, more number of samples will lie around the mean and to the left and right side of the mean you have, you will have fewer samples. Okay, however, if it's some moderate quality control, so then it will be worse than good. Like, so basically more samples will lie around either side of the mean and less of the samples will have the median or mean strength. And the poor quality control, it's like, so most number of samples will lie on either side of mean strength and least number of samples will have the mean strength.

So, you can attribute. The good quality control for the concrete that's produced in a batching plant in controlled environment with temperature controlled and then sophisticated machinery and all that stuff. While poor quality control concrete can be attributed to concrete produced on site with usually manual more of manual methods like labor doing the mixing. You will have a mixer, rotating mixer, but it's usually the materials will be poured by hand possibly. And then it's also possible that you will have certain discrepancy in the ratio of cement, sand and coarse aggregate.

So that might also lead to some poor quality control. So that's what that's what it is. I mean, that's how the concrete strength varies with the quality control. So this graph over here, it shows the characteristic strength of a concrete on a curve. So basically, say, as I have mentioned earlier that you have normal, the concrete specimens tested from a given batch or given mix, follow a normal distribution or Gaussian distribution. So if that follows the coefficient distribution, then if this is the mean strength, then the characteristic strength is, I mean, the area under this curve is 5% and this is the 95% area.

So technically, what do you mean is that like 1.65 times the standard distribution or 1 points, this sigma is the variance of this probability, this sigma is the standard distribution of this normal distribution curve. So 1.65 times to the left side of mean will give you the characteristic strength if you plot the normal distribution curve for a concrete mix. So kind of technical, but it's always good to know stuff. So we have talked about the the compressive strength of concrete and then the characteristic strength of concrete.

Now, there are different grades of concrete. OK, you have M10, M20, M15, M25, M30, M40, etc, etc. So now the when you plot the stress strain curve for different grades of concrete, this is how it looks like. So for M15, say this is the stress strain curve for M20, for M30, for M40, M50. So if you take a close look, the ductility as the concrete strength increases, the ductility of concrete decreases. So basically the M15 will have higher failure strength, M15, M20, M30 has a failure strain of about 0.004, but M30, M40 has a failure strain of approximately 0.0038 and M50 has a failure strain of 0.003 approximately.

So the as the strength of concrete increases, the concrete becomes less ductile. It fails early. Once it reaches its maximum strength, then boom, it crashes. Also, another aspect that can be noted from this figure is that the strain at which the concrete or concrete specimen reaches its maximum strength also increases as the concrete grade increases. So basically M15 reaches its peak strength, say at about 0.0018, if I drop a perpendicular over here, so is 0.0018. For example, then M20 will reach at 0.0019, M30 will reach its maximum compressive strength at 0.002, so on and so forth.

So M50 will reach its compressive strength at approximately 0.0022. 0.002, so something like that. So, so basically the strain at which the concrete reaches its ultimate strength also increases as the grade of concrete increases. Okay, same thing basically that the as the concrete grade of strength increases, the ultimate failure strain, ultimate failure strain, this one of the concrete decreases, that is the ductility of concrete decreases or basically we can say that M50 is less ductile than M15. The ductility of concrete decreases with increased strength and the strain at maximum strength.

So the strain at maximum strength increases with increasing concrete strength. Okay, now until now we have seen looked at the compressive strength of unconfined concrete, uniaxial compressive strength of unconfined concrete. Okay, what will happen if you confine the concrete in the lateral direction and then start applying the uniaxial load from top? So that is that is called so confined strength of concrete. So basically we will be confining the test specimen by lateral pressure and then you apply the uniaxial compressive load and then the compressive strength of concrete is recorded.

So now it has observed that the uniaxial compressive strength of confined concrete specimen is more than its unconfined counterpart. Okay, so unconfined concrete has certain strength if you confine the concrete. So if you apply a lateral pressure, you apply a lateral pressure, you are not increasing the pressure. You are just keeping the lateral pressure constant and then start increasing the axial load. Okay, or axial pressure and then you start just the axial pressure will increase and based on that. So the and then you note the failure load at which that confined concrete fails.

So that failure load will be more than that of an unconfined concrete. Also confined concrete has a larger failure strain, which means that it is more ductile than unconfined concrete. Okay, so confined concrete has larger failure strain making it more ductile than unconfined concrete. So just to show with an example. So this graph over here shows the variability of compressive strength uniaxial compressive strength of a confined concrete sample. So what you see over here is you have a sample you apply lateral pressure. So here this Sigma 3 is uniform all across the sample.

Okay, this Sigma 3 is uniform all across the sample and then you start applying Sigma 1 and it in this Sigma 1 increases. I mean first it is 0 and then you start by 1 MPA, 2 MPA, 3 MPA. You keep applying keep increasing the Sigma 1 and Sigma 3 is kept constant. You keep increasing the Sigma 1 and then you note the strength at which the specimen fails. Okay, you note the strength you plot the stress strain curve basically. So you note the strain and stress.

Okay, keeping the Sigma 3 same. So now this graph over here this small one it shows it it's the stress strain curve for Sigma 3 equals 0 basically no lateral pressure. So that means unconfined concrete which we were looking into in previous slides. So no confinement. So Sigma 3 equals 0. So this is the stress strain curve. Okay, so failure strain is what say approximately 0.005 or 0.006 maybe just for this. I mean, I know I've mentioned that it's approximately 0.003 but just for the sake of it, you can say that okay, it's around 0.005.

So now just see when you apply a pressure of lateral pressure of 3.8 MPA just 3.8 MPA. So not much the failure strain, the compressive strength, the compressive strength of this sample is approximately what 20 say around 20 MPA or maybe 25 MPA. Okay, when you apply a lateral pressure of 3.8 MPA, this Sigma 3 is increased from 0 to 3.8. The failure strain, the failure strain, it increases to approximately 0.03. So the failure strain increases by about 4 times, 3 to 4 times. Okay, then the unconfined concrete and the maximum compressive strength, it increases from 25 to approximately 50.

So compressive strength also doubles. Next, you will see if you again increase the confining pressure, the failure strain increases, further increases and the compressive strength also increases. Similarly, as you keep increasing the lateral pressure, Sigma 3, the 13.8 MPA, you, the failure strain keeps on increasing. Sigma 3 equals 0.03. 28 MPa, the failure strength keeps on increasing. So 0.06 and the compressive strength is like it reaches, it goes around 140 MPa. Okay, so that the purpose of this thing is to just to show that what is the effect of lateral pressure on confined strength of concrete.

So the lateral pressure plays a significant role in increasing the ductility of a concrete and also increasing the compressive strength of concrete. So if you apply lateral pressure, if a concrete is confined, its failure strength, it becomes more ductile and its compressive strength also increases. So now, why is this important? Why are we talking about confined concrete? So now, in beams, usually, we apply, we have what do you call as shear stirrups or hoops. Okay, so shear stirrups or hoops, they kind work as confinement. So basically, what they do is, the concrete that is inside that shear stirrup or in fine inside that hoop is confined by that stirrup or that particular hoop.

Okay, so, so, so, so that steel stirrup applies pressure on the concrete that is, that can, that steel stirrup can be assumed to apply pressure on the concrete that's within that hoop or stirrup. So, so, so that area of concrete that's within that stirrup is called a confined concrete core. Okay, let's look into, you know, how, what confined concrete is in structural elements for this. So, so, so, say for example, you have this, you know, column element. So, in column element, you have this stirrups and hoops.

So, this is the stirrup. Okay, this is the stirrup. And this is the main reinforcement. And this is the concrete cover. So, now, the concrete that is inside this stirrup. So, this is the stirrup. So, concrete inside this stirrup. So, this basically, this whole concrete is confined by this circular stirrup. Okay, so, this stirrup basically applies a confining pressure on this concrete core. So, this is called effectively confined concrete core. Similarly, in a beam element, you have this longitudinal reinforcement, two longitudinal reinforcement, and then you have shear stirrups.

Okay, so, now, this concrete within this shear stirrups, this concrete core is confined by this shear stirrup. So, this shear stirrup applies pressure on this concrete confinement. Okay, so, confining pressure. So, because of this confinement, because of the confining pressure by reinforced concrete, the failure strain of this concrete core and this concrete core over here, the failure strain will increase. This or in other words, the this concrete core is more ductile than an unconfined concrete sample. Okay. So, now, confined concrete, where is it useful? So, confined concrete is significant for seismic design, which usually has large displacement demand.

So, when an earthquake comes, the structure has sways a lot from sideways. Okay. Structure sways a lot sideways. So, basically, displaces a lot from its mean position. So, now, if concrete is ductile, then and only then, the members will have the or the structural elements will have the capacity to displace sideways to cater to that demand, to cater to that seismic demand. So, now, so, that is why the confined concrete comes into picture in seismic design, basically. So, in seismic design, usually, you provide the shear stirrups at closed spacings.

So, that closed spacing ensures that the concrete core is effectively confined. And due to confinement, it has large ductility. And due to large ductility, it can displace more under seismic effects. So, that's a little bit about confined concrete. We will not touch this part in more detail in this course. It was just an overview. It's usually discussed in when you guys get to study the seismic design, you will learn more about confined concrete. Then, the next important thing is the tensile strength of concrete. So, like you have compressive strength of concrete, you will also have something called tensile strength of concrete.

So, tensile strength of concrete is defined by what we call as the modulus of rupture of plain concrete. So, to figure out the modulus of rupture of plain concrete, there are multiple ways, okay. So, one of the way is like you have a concrete beam of width B and height H. And then, it's supported on two ends, simply supported. And then, you apply load P at one third points, okay. One third from each end. And then, you keep applying the load. And you apply the load and you increase the value of loading eventually.

Slowly, slowly, slowly, slowly, you increase the value of loading. And then, the point at which the concrete cracks at the bottom and fails. Because this is a simply supported beam, so the tension will be in the bottom. So, at the bottom, you will see tensile crack. Okay. So, the point at which you will start seeing cracks, large cracks, that can be assumed as the end of the test. And the load at which that failure occurs is noted. And then, the bending moment due to that load can be easily computed, which would be PL over 3.

So, that is, that bending moment is MCR. Okay. And then, the modulus of rupture is given by 6 MCR upon BH square. So, this is nothing. This formula is derived using the simple strength of material equation, which is M by I equals F by Y. So, this F is the rupture modulus and M by I times Y is the section modulus M by Z. So, this BH square over 6 is the section modulus. So, M over Z is the modulus of rupture. So, and MCR again is PL by 3, where P is the load at which the concrete beam fails or start showing cracking.

Then, another method to test the, to figure out the modulus of rupture of concrete is the split cylinder test. So, in split cylinder test, what you do is you have a concrete specimen of length L and diameter D. And then, you apply load like this on top and bottom. So, so, on bottom it is supported. So, this is the reaction that you get from the bottom. And then, you will, at, from the top you apply compressive force. Okay. So, this is the, this is how the state of stress looks like on the cylinder.

Okay. This is how the state of stress looks like. So, compressive force, compressive force. And then, of course, you will see transverse tension because, remember, concrete is a brittle material. So, it will fail in tension. Brittle material always fail in tension, fails in tension. Okay. So, this is a brittle material, fails in tension. So, you will see longitudinal cracking. Longitudinal cracking means there is tension at the center. If you take an element at the center, so this will be the state of stress in that element.

Okay. So, sigma one, sigma one. So, if you plot the, if you, if you plot the stress distribution. So, that stress distribution can be, is, is as shown. So, basically, on the top part over here, you will see some compressive stress. But, at, as you start moving down the diameter of the cylinder, you will primarily see the tensile stress. So, this tensile stress is manifested here. So, this tensile stress is manifested here. So, this tensile stress is, you will see the tensile stress. So, this is the tensile stress.

So, that is, you know, it's the tensile stress. So, this is the tensile stress. where P is the load at which you observe cracking. So 2P upon pi times length of sample times diameter of sample. Okay. So that's the modulus modulus of rupture from split cylinder test. And IS code says that, you know, no need to do all this testing and all for practical purposes or for all design purposes. You can use modulus of rupture equals 0.7 times FCK under root FCK, which is a decent assumption or which is a decent approximation of modulus modulus of rupture.

Now, another important property of concrete is it's creep. What is creep? So what happens is, so at sustained compressive load, say a beam is there, a concrete beam is there and you place a load on that concrete beam. Okay, say load is P. And then you leave the load like that. You don't change the load. You don't increase the load. You don't decrease the load. With time as so as soon as you apply the load, that element will deflect somewhat deflect somewhat. Okay. Or basically, you will say that, okay, due to that load, there is some strain in concrete.

But if you keep that load long enough, okay, for say, one year, two year, three year, as time progresses, even if that load hasn't changed, the strain in concrete increases. So that is called creep. So basically, at sustained compressive load. So the compressive load is same, it's not changing with time, the deformation of a concrete element keeps increasing with time, which is due to a phenomena, which we call as creep. So this phenomena occurs, even though the stress is constant, you're not not changing the stress. So what does this do? So basically, say, if you have a beams or slab, and they are subjected to same load over, say, five years, over five years, they are being subjected to same load, the load hasn't changed at all.

So in the beginning, if the deflection of that beam or slab was say, one millimeter, after five years, that deflection might increase to 1.5 millimeter, or 1.2 millimeter, or depending on what is the creep. Similarly, if you have say columns, and you apply load on the column, due to that loading, say, column buckles slightly, or there is a small lateral load on the column, very small lateral load, okay, due to which the column buckled initially, so there's a slight buckling, and then that lateral load is removed, and you apply a vertical load, okay, sustained vertical load, you're not changing the load over a number of years.

Okay, say five years. So under the effect of that sustained load, that sustained load on the column, the what will happen is due to creep, the column will deflect more, more, more and more sideways. So due to the sideways deflection of that column, it might happen that column might buckle under the effect of compressive load. So that's why creep understanding creep is very important in reinforced concrete. So practically, creep is used just to compute deflections. So using for in practical RCC design, you just say that, okay, you know, I will compute deflections, or I will anticipate what is deflection due to that creep.

And we'll see and then you say that, okay, if this this is the maximum deflection that I'm expecting because of creep and normal loading, and it is okay to have this much deflection, or it is not okay to have this much deflection. So let's change the design something like that. So what does IS code say? How does IS 456 handle creep? So let's take a look with at some example example. So before that, just I will just try to explain all of that I have said with the help of a graph.

So at time T0, so at time T0, you apply a load. So due to that load, you have a strain, but then you keep the load constant. So with even if the load load is this, so this strain is called elastic strain, and then you keep the load constant, but the you see that the strain increases with time. Okay, so that strain is called creep strain. Okay, that strain is called creep strain. And then at after some time T, say this, whatever time it is, you remove the load. So immediately the structure of the element that was deformed, it will undeform or basically it will recover some of that recover from some of the deflection.

So that recovery is called elastic recovery. And then with time over a period of time, it will recover some more of deflection, which is called creep recovery. Okay, but there will be certain permanent deformation in the member. I mean, you cannot undo this deformation. So that is called the permanent deformation member. So the idea is that you apply a load. So you have elastic strain, then without changing the load, the strain increases. So that is called the creep strains. Okay, now IS code says that what you need to do for creep, you just say that, okay, you know, my effective models of elasticity, because of creep is equal to EC or which is 5000 under root FCK for concrete time divided by one plus theta.

So theta is mentioned in IS code as depending upon the loading of the member theta is either one, 1.1 or 2.1 in IS code. So what that does is, so if you have theta equals 1.1, so then one plus 1.1 is 2.1. So you are dividing EC by 2.1. So basically, you are reducing the modulus of elasticity of concrete. So if you are reducing the deflections that you get while calculating that will increase. So let's see with the help of an example. So now say M30 grain of concrete and deflection is to be computed.

So now EC equals 5000 under root FCK. Okay, so that's 27386 MPa theta equals to 1.6 because the beam is loaded at 28 days. Okay, so now ECE means the modulus of elasticity. Effective modulus of elasticity for creep will be ECE 1 plus theta EC upon 1 plus theta. So 27386 1 plus theta theta is 1.6. So that gives me 10533 MPa ECE. Okay, so now the deflection without creep. Okay, so the deflection in that member without creep will be proportional to 1 over EC and the deflection with creep will be proportional to 1 over EC. So thus, this will be proportional to 1 over 1 over 1 overinal effect of creep. Whoa. Then there is 4.6. We can see that you know ECE over EC. Okay, ECE over EC. So thus, the total deflection including the effect of creep will be 2.6 times the initial deflection. Okay, the total deflection, including the effect of creep will be equal to two times 2.6 times the initial deflection. So basically what you what I'm trying to say over here that IS code says that okay, you know, due to creep, the deflection will be two times more. So just take that into consideration and then design your structure element. Another strain that's important in concrete is the shrinkage strain. So concrete shrinks as it hardens. Okay, concrete shrinks as it hardens. So this induces additional strain in concrete element which is termed as shrinkage strain. So now, again, these strains again cause additional deformations in concrete and you are supposed to compute that. Okay, so unlike creep shrinkage does not depend on the loading or stress in the element. It experiences concrete experiences shrinkage even if it is unloaded and shrinkage strain will shrinkage and will induce additional deformations apart from elastic deformations and creep deformations. So basically when you complete the deflection of an reinforced concrete element, there there are usually three components, the creep deformation due to creep deformation due to shrinkage and elastic deformation.

So just we have to keep that in mind. So now what IS code suggests that in absence of any available data, IS code suggests that you can we can adopt a maximum value of shrinkage strain. So yeah, so just just you can assume that you know, one one times epsilon CS, which is again provided in is 456. So that's all I guess we will wind up this session. Now in this session, we looked at the characteristic strength of concrete, what is the variability of in concrete strength depending upon quality control. And then we looked into what is a confined concrete and how does its compressive strength differ from unconfined concrete and then we looked at the creep and shrinkage strain in concrete and how is it handled in IS code. So that's the end of session three. We will for week one and we will continue with the last session of this week one series. So in that, we will discuss about reinforcement and the properties.

Steel reinforcement in concrete. Okay. So, yeah, let's meet next time.

Want the rest of Reinforced Cement Concrete Design?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Reinforced Cement Concrete Design course

The remaining 66 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Reinforced Cement Concrete Design course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.