Lesson finished
Up next: Characteristic Strength, Confined Concrete, Creep and Shrinkage
Unlock all 69 lessons of Reinforced Cement Concrete DesignFull course ₹40,000 · paid
Concrete Ingredients, Compressive Strength Tests and Stress-Strain Curve
A free lesson from Skill-Lync's Reinforced Cement Concrete Design course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”
What will you learn in this free Reinforced Cement Concrete Design lesson?
The instructor covers the four constituents of concrete, admixtures such as retarders and accelerators, and what a grade like M40 means. It explains uniaxial testing on 150 mm cubes and 150 by 300 mm cylinders, then the IS 456 parabolic stress-strain curve with failure strains of 0.002 and 0.0035.
- Cement, water, coarse and fine aggregate roles
- Cube versus cylinder compressive strength
- Effect of height to diameter ratio
- IS 456 design stress-strain curve
What comes after lesson 2?
The next free lesson is lesson 3, “Characteristic Strength, Confined Concrete, Creep and Shrinkage” (40 min). Later in Skill-Lync's Reinforced Cement Concrete Design course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 69 lessons (31 h 42 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello and welcome to the course on Reinforced Cement Concrete Design. So this is the week one lecture. We are continuing with the week one and this is week one session two. In the session one, we looked into different objectives. What are the different objectives of structural design? Basically, the strength, stability and serviceability, these three concepts. And then we looked into what are the different structural systems? What is a structural system pertaining to general structural design? So we looked into the example of building frame and then of example of water tanks. And then we looked into the importance of design codes and what are the design codes that are primarily applicable for design of reinforced concrete structures.
So let's continue with week one. So let's continue with week one. And today we'll look into what is concrete basically and what are its characteristics. What are its is actually that's if you would have taken a course on concrete technology there, they talk about different materials that that concrete is made up of and how get different qualities of concrete. But I'll just go briefly through that. So concrete is made up of four primary materials that's cement, water, coarse aggregate and fine aggregate also called as sand. So now cement of they it is a binding material binding agent that binds all the coarse material coarse and fine aggregates together.
So the water reacts with the water reacts with the chemicals in the cement to so that it could act as a binding agent. Cement comes in usually three common grades of cement that's that is usually used for production of concrete. So it can be usually say grade 33, 43 or 53 cement. So grade 33 means the compressive strength of the cement is 33 megapascals. Then for water, I mean, there are certain criteria laid out in IS456 that how the what should be the water quality, it should be free from any organic material, it should be clean, it should not have any chemicals, it should not be alkaline or acidic.
So that otherwise it might react with the aggregates or cement in a different way, you don't want that. So water should be basically clean. So that's another concept. And then you have the third considerate is coarse aggregate coarse aggregate is the aggregate that that are sized between 4.75 mm to 20 mm. So in a sieve analysis. So that's the size range, I mean, 4.75 mm to 20 mm is the size range for coarse aggregates. And then fine aggregate is anything between 0.075 mm to 4.75 mm comes in the category of fine aggregate.
And what is the grading of fine aggregate and what is the grading of coarse aggregate that you need that's a different topic to study all these these are the four major constituents that make up concrete and combining the coarse aggregate and sand the aggregate constitute about 25 75% of the total concrete volume. So if you have one meter cube of concrete. So out of that 0.75 meter cube would be just aggregates and the rest 25.25 meter cube by volume would be cement and water. So in addition to these four major ingredients, usually admixtures are also added to enhance certain properties of concrete.
For example, there are admixtures like plasticizer. So what does plasticizer do? It's it basically increases the workability of concrete. So workability means it the concrete becomes more flowy, it can flow freely. So in the concrete can become flowy or it's workability is increased. And then another example is an set retarder. So set retarder is basically an admixture that increases the setting time of concrete. So what does that mean is if you make prepare a concrete mix at and it should usually it takes say 30 or 40 minutes for initial setting.
If you add a retarder, then it will take say two hours to set for its initial setting time increases to two hours. So what do you want that you want that in cases where your concrete is being prepared in a batching plant that is say 20 kilometers away from the site. So you prepare the concrete, you put it in a truck and you cannot say for sure that your truck will reach on the site in 20 minutes because that's the setting time initial setting time of concrete.
So you add set retarder so that the initial setting time becomes say two hours or three hours and then you can when your truck reaches your site, the concrete is still wet and has not set. So that's the purpose of retarders. Then another admixture that's commonly used is set accelerator. So accelerator is the opposite of retarder. So basically, if you're setting time for concrete is say 20 minutes, if you add accelerator, your initial setting time of concrete will reduce to say five minutes or 10 minutes.
Why do you want accelerator? So for example, if you want to do a lot of concreting, you have just 12 hours and you want to do a lot of concreting. Usually concreting is done in batches. So first batch you did the concreting and then you cannot do the second batch until the first batch is set. OK, not permanent set, but initial set. So unless it is set, you cannot do the second batch. So what do you do is so so that you can work rapidly, you add accelerator so that once you pour concrete, the concrete sets pretty fast compared to without accelerator.
And then you can pour the second batch and then third and then later. So that's why so that you can finish your work early. So that's the purpose of accelerator. And concrete mix design is just for the guidelines that dictate the proportions of constituents. That is the cement, sand, coarse aggregate, etc. So concrete mix design is a separate subject where you study that. OK, how much cement, sand or coarse aggregate you are supposed to mix so that to it so as to get a desired strength of concrete.
OK, say you want M20 or M30. So concrete mix design guidelines will tell you that. OK, how much cement, how much sand, how much coarse aggregate, how much fine aggregate you need to mix and like that. So roughly speaking, one is to two is to four by weight. That is this one is cement, fine aggregate, coarse aggregate. So one portion of cement, two portions of fine aggregate, four portions of coarse, coarse aggregate and then some water. So water is usually 40 percent of cement roughly. So that will give you M20 grade of concrete more or less.
It's it's it has been seen that that gives you M20 grade of concrete. This is just a tentative thing. I mean, when you do mix design, you need to have certain more criteria. Yeah, like what should be the grading of coarse aggregate, what should be the grading of fine aggregates and all that stuff. Again, a different topic. I digressed. But yeah, important to know, at least as a structural engineer, you are supposed to know about this stuff. Then let's go on to what is the compressive strength of concrete and how do you measure the compressive strength of concrete?
So usually the in practical structural design purposes, we use something called when when we mention concrete, we say that we have M20 grade of concrete or M30 grade of concrete or M40, M50, something like that. So M40, so when we say that the concrete grade is M40, so that means the uniaxial compressive strength of that concrete is 40 Mpa. So what we will try to do is we'll try to figure out how do you come up with that 40 megapascal value? How do you know that?
OK, that concrete specimen is having a 40. What are the test criteria? What what are the loading conditions under which you test the compressive strength of concrete? And you reach to a value of 40 megapascal. So the first thing is like, you know, you prepare a concrete sample. So it's it's a standard sample usually. So in India, we use concrete cubes. So and across in Europe and US, they use standard cylinders. So these are the standard specimen standard is so standard. And I say standard because the dimensions of these specimens are fixed.
So you cast a sample out of a given concrete mix and then you apply load on the sample. So now you see these are two samples. This is cube and this is cylinder. So now on top of the so so you apply load from both top and bottom. So bottom is just a plate for support. And from top you apply the load. And this is this is where the reaction comes from. OK, so here you will have reaction. You apply load P from top. You will have reaction P from bottom.
So now when you apply load P. This plate, since it covers the entire top surface of the cube, you will have uniform loading on the top surface of the cube. So similarly for this cylinder, when you apply load P, that is transferred to this loading plate. And then this loading plate transfers the force P onto this cylinder as uniform loading on the top surface of the cylinder. OK, so now that's how the loading is applied and note that the load is in one direction, just across along this direction of the cylinder and along this direction of the cube.
There's no stress or load in the lateral direction. So that's why it's called uniaxial compression means compression acting along one axis of the specimen, only one axis. So that is the vertical axis. That's why uniaxial compression, very important. No lateral stresses are acting on this specimen. So you have to ensure that. Then just we will just briefly touch that what are the specimen sizes. So for Europe and USA, the cylinder is used with that has a diameter of 150 mm and a height of 300 mm.
And the height to diameter ratio is, of course, 2.0 for India. We use cube and the height to lateral dimension cube having a dimension of 150 mm. So the height to lateral dimension is 1.0. So again, let's go back to this slide. So we have seen that, okay, what are the specimen sizes, okay? So for cube, it's 150 mm and for cylinder, it's 300 mm and 150 mm diameter. So when you start applying load, at some point, this specimen will fail. Basically, it will crack and it will crush under the effect of compressive load.
So the load at which it crushes, that is the failure load for the specimen, okay? Simple, nothing fancy. The load at which the sample phase, that is the failure load. And then how will you compute stress? So the load divided by the surface area, top surface area of the cube and top surface area of the cylinder will give you the stress, the failure stress. So that's very basic. So now we've seen that there are two different samples that's that are used, okay? Cylinder and cube. So now what happens is when the lateral dimensions, the compressive strength of concrete also depends on the type of sample that you are testing.
So if the height to lateral dimension of the sample is different of the, you have two samples, cast from a same concrete batch. And if the height to lateral dimension of those two samples are different, the compressive strength of those two samples will be different. That's what that's shown over here in this graph. So that's basically the height to diameter ratio or height or height to lateral dimension ratio. You can also call it height to lateral dimension ratio. So now if say this is the standard say, remember we saw that for cylinder, it's height to diameter ratio is 2.0.
So this is the standard value 2.0 height to diameter ratio. And you have say thus if the relative strength is of course one for this. So now if you have a height to diameter ratio of one, so basically your height is also 150 mm and your diameter is also 150 mm for the cylinder. Then the strength, the compressive strength of that sample would be 1.18 times or 18% more than the standard cylinder. So as lateral dimension of the sample reduces height remaining the same, the compressive strength of the sample or specimen increases.
So by this logic, you can always say or you would have already, I guess you would have guessed that the since the height to lateral dimension ratio of cube is one. So the compressive strength of cube specimen that we test in the labs will be more than the compressive strength of cylinder that we test, that we would test standard cylinder that we would test in the lab. Okay, so that's the basic logic that when you are testing a sample in the lab, the specimen size or specimen dimension plays a major role in determining what is what would be the compressive strength.
One more thing, one more thing that's going on over here is when you apply load on top of the specimen, the this plate, this plate provides lateral restraint to the cube at the top. So, so basically lateral restraint means remember some time back I mentioned that you do not have any lateral stress on this cube, but due to this plate, you will experience some lateral stress at the top surface of the cube. So that's called lateral restraint, not only on the cube, but on the also on the cylinder lateral, you will experience some the specimen experiences some lateral restraint.
So we will look how that affects. So that lateral restraint is also called platen restraint, basically, and that occurs due to the friction between the plate loading plate and the top surface of the concrete specimen. So now when you apply compressive load on concrete specimen cube or cylinder, ideally the cracks should be vertical, that would indicate the failure of the concrete, okay, the crack should be vertical, but that does not happen. Practically, remember, I talked about load platen restraint. So what the platen restraint does is it applies some lateral stress as well towards the end, just on the top surface, it provides some lateral restraint for some top portion and for the cube, it's for some top portion, you get some lateral restraint, okay.
So due to that, the cracks are not vertical, okay, the cracks are not vertical, not like this, but they incline because you have two stresses acting over here, one like this, and then one like this. So the cracks become inclined. Also, we will see later that when a concrete specimen is subjected to two stresses, I mean stresses in lateral direction as well, the compressive strength of concrete increases. So practically, you will start seeing vertical cracks at the mid, at mid of the specimen. So at when you, when you move down the specimen, the effect of lateral restraint goes away.
There are no lateral stresses and acting in this direction. Okay, no lateral stresses. So you will start seeing vertical cracks and you will see vertical cracks first and then you will see the diagonal cracks because the compressive strength of concrete is increases due to lateral stresses. So over here, the compressive, the concrete will fail later at a higher stress compared to concrete that is over here because there are no lateral stresses. Just to reiterate or just to repeat the crack pattern. So ideally, we are expected to see vertical crack pattern, but that does not happen because at ends, we see lateral restraint due to the loading plate.
So that increases that induces some lateral stresses in the concrete specimen because of which we see diagonal cracking. But as we move down, the effect of lateral stress diminishes and we see vertical cracks. Okay. Also, remember, we talked about that this, this part that height to diameter ratio. So basically height to diameter ratio for cylinder is height or height to lateral dimension for cylinder is 2.0 and height to lateral dimension for cube is one. So the basically for the cube will have higher strength when for the same concrete batch cube will have higher strength.
So it is seen that the compressive strength of cylinder is approximately it only 80% of the cube strength. Okay. So the same thing that I mentioned, the crack pattern over here, that cracks tend to develop parallel to the direction of compression. Platten restraint at ends prevents vertical crack near the ends moving away from the loading phase, which that is moving away from the loading phase. The vertical cracks are observed effect of lateral restraint because the effect of lateral restraint diminishes. So thus vertical cracks are observed as we move away from the loaded phase till now we have seen that, okay, how the concrete specimen that particular concrete specimen, which is the cube or cylinder will behave under the effect of compressive strength, but you don't see practically in buildings or in other structures, you will have concrete in different shapes.
You will have beams of large, that has large length, rectangular cross section, but large length. You can have circular columns that will have the whose height will be say three meters, but the dimension or diameter would be only maybe 300 mm or 400 mm. So the height to diameter ratio, what I'm trying to say is the height to lateral dimension ratio varies for different concrete elements in the structure. Again. Also, the standard concrete specimens, that is, cubes or cylinders are tested under uniaxial compression. But when you go into an actual structure, the actual concrete specimens are subjected to various loads in addition to uniaxial compression, which can be bending, shear, then tension, sometimes tension, all this stuff.
So, basically, what you are doing in lab on the specimen, that does not replicate or that is not a true judgment of what all loads the actually a concrete element would be subjected to in an actual structure. So, and again, so, basically, so, due to all these aspects, what happens is, due to all these aspects, the apparent strength of concrete, okay, the apparent strength of concrete is, in elements like beams, columns, is usually less than what is observed during testing under uniaxial compression. Okay, so, okay, so, just, we will try to understand what, again, I'll repeat that the apparent strength of concrete, what does that, what is the apparent strength?
So, the strength of concrete in a, when you cast the concrete in a beam element or a column element or some other shape for that matter, some other element for that matter. So, the strength of that element will be lesser than what is observed on a standard specimen that is loaded under uniaxial compression, okay? So, now, practically, it is observed that for cubes, for cubes, the apparent strength of concrete is 67, approximately 67% of the actual strength of concrete that's observed in lab or the testing strength of concrete observed in lab, okay?
So, say, so, say, so, say, this is a standard cube that we test in lab and this is the beam element. So, if the compressive strength of this cube is FCK, then the strength, while for design purposes, we will assume that the compressive strength of this beam element is alpha times CK, where alpha is 0.67, okay? So, this is, again, this is, again, the apparent strength of this compressive strength of this beam element is alpha times CK, where alpha is 0.67, okay? So, this is how the, this is what the behavior of concrete element in structure is.
Next, we will look into another important criteria, another important aspect, that's the stress strain curve of concrete for compressive strength, very important. As a structural engineer, you are supposed to know that how, what's the models of elasticity and how do you, the concrete behaves under different stresses, what are the strains, what are the failure strains and all that stuff. So, let's go into that. So, the stress strain curve, concrete being a non-linear material, non-linear, non-homogeneous material, the stress strain curve will always, of course, be non-linear.
So, that's what you see. So, for the initial portion up to the 0.4 times its compressive strength, the 40% of its compressive strength, the stress strain curve is linear. And the cracks, when you start loading a concrete specimen and you have, you start increasing the load so that the stress is increases from say from 0 to 0.1 to 0.2 times of F prime C or 30, then 30% of compressive strength, then 40% of compressive strength. So, you start seeing the cracks, but those cracks will be stable.
Basically, they will form, those cracks will be vertical and stable. They won't propagate like this. If you remove the load, those cracks will close and it will look like the specimen, it will look like the sample will not, it will not look like that the sample has been subjected to any load. So, that's stable crack propagation. But when the stress is increased beyond 40% of compressive strength of concrete, you start seeing the non-linear behavior of concrete. Okay. You start seeing the non-linear behavior and non-linear behavior is because the cracks, they are now unstable.
So, the cracks propagate haphazardly. So, in this below 40% of compressive strength, the cracks start initiating and then once the stress increases beyond 40%, the cracks starts propagating. Even if you remove the load, you will clearly see some cracks. There will be permanent, some permanent cracks in the concrete specimen and the stress and strain is no longer linear. It varies non-linearly. So, now and then you will see that the maximum strength of concrete is achieved at a strain of approximately 0.002 and then after that, the strength decreases, decreases, decreases and at this point, finally, at this point, the concrete crush permanently.
Finally, okay, the concrete is crushed and we say that failure has occurred and this strain is roughly 0.003 or 0.0035 usually between that 0.003 and 0.0035. So, that's the failure strain of concrete and the note that at failure strain, the strength of concrete is less than its maximum compressive strength, which is Fc. So, the failure at failure, the compressive strength of concrete is less. So, that's what the compressive, the peak strength occurs at a strain of 0.002. The failure occurs at strain of 0.003. So, the characteristics of this strain curve is like, so for the linear part, you have, again, the modulus of elasticity is, you can say that, okay, E linear or E C or whatever you want to say.
Then, so this is the basic, then at any point O, you draw any point O on the curve and then if you draw a line from the origin to that point O, the slope of that line is called secant modulus of concrete, secant modulus. And if you draw a tangent modulus of concrete, and if you draw a tangent at point O, that's called tangent modulus of concrete, IS456 adopts secant modulus of concrete for all practical purposes. And it gives a formula, 5200 root FCK is the formula for secant modulus of concrete.
This is as per 6.2.3.1 of IS456 2000. So, it is good to know about the initial modulus of elasticity and tangent modulus of elasticity, but for all practical purposes, we'll be using this, the secant modulus of concrete, which is 5000 under root FCK in our design calculations. Now, if you observe closely, this stress strain curve of concrete is roughly, you can categorize it to be parabolic in nature. So, the, what has happened is like the parabolic stress strain curve for concrete has been studied extensively. So, based on those studies, there have been attempts to develop a stress strain curve using for concrete, for a given concrete grade using algebraic expressions.
So, researchers have always, researchers are always curious that as to how can we develop something analytically. So, there have been attempts to develop an algebraic expression for the parabolic stress strain curve of concrete based on the numerous studies that has been done. So, one of the most commonly used expressions or one of the most commonly used algebraic expressions for developing the stress strain curve of concrete is modified Hognestad parabola. So, this is how it looks like, so basically, what's done is, so this, you can generate this stress strain curve of concrete based on just three correct, three things.
All you need to know is the modulus of elasticity of concrete, which is 5000 under root FCK as per IS456. Then, this, then this F double prime C is the failure strength of, the ultimate strength of concrete F double prime C is ultimate strength of concrete. Then, EC is the strain of concrete at any point. Okay, at any point. E0, epsilon, epsilon 0 is 1.8 times F double prime FC by EC. So, that's this and then, you will have the EC again strain at any point and epsilon 0 square.
So, this, this, this, this expression over here, this, what this will do is, this will generate this whole parabola or stress strain curve for concrete. Basically, this is a parabola up to here, this point up to the compressive strain and from there, it follows the linear path and this is 0.15 F prime C. The, the, the, the purpose of this analytical equation is usually. For design, it won't be used that much, but for research, usually when you are running some finite element models and all that stuff, and you need stress-strain curve of concrete, so there you can adapt this stress-strain curve for concrete, develop a stress-strain curve for concrete and use it for research purposes.
But it's always a good idea to know how things work, so yeah. Then, most important thing that we will, we are bothered about, we are structural engineers practicing in India, should be bothered about is, what is the stress-strain curve for concrete as per IS456? So, IS456 adopts a parabolic linear stress-strain curve, the IS code also limits, IS code mentions that the failure strain of concrete is 0.002 under direct compression and 0.0035 under flexure. So, this is an important clause to remember, so this is an important clause to remember, and we will talk more about it later when we go on to talk about beams, and when we go on to talk about columns, then we will talk more about these things, the 0.002 and 0.0035.
So, let's see how the stress-strain curve for IS456 looks like, so it adopts a parabolic curve up from 0, it rises parabolically up to 0.002 strain, it's parabolic, and then it adopts a linear variation, linear variation up to failure strain of 0.0035. So, IS456 says that up to 0.002, the stress-strain curve of concrete is parabolic, and then from 0.002 to 0.0035, the stress-strain, the stress-strain value remains the same, and the strain, only the strain increases, and the failure strain is taken to be 0.0035 for flexure, okay?
Now, again, remember, so this is the actual stress-strain curve for concrete specimen, which is obtained by testing of concrete specimen, okay? Remember, we talked about the apparent strength of concrete, so that which is the apparent strength of concrete for structural members like beams and columns that are subjected to different types of loading and has different height to lateral dimensions. So, the apparent strength of concrete was 67.67 times the ultimate strength, right? So, this is the apparent strength, stress-strain curve, this is the stress-strain curve based on apparent strength of concrete.
So, what you do is you just multiply all of these values in the graph by 0.67, it drops down, so 0.67 times FCK, this curve. And then the final design curve that you get is 0.67 FCK times the gamma M, which is the material factor of safety for concrete. And it is 1.5, we will look more into it, but for now, you can just remember that, okay, this gamma M is 1.5, so 0.67 times FCK divided by 1.5. So, this stress-strain curve is based on that, okay?
So, I will repeat, the IS-456 adopts parabolic linear stress-strain curve for concrete. And this is the true or actual stress-strain curve. This is the stress-strain curve for apparent strength of concrete. And this is for the design stress-strain curve for concrete. So, this curve we will be using for inner practical designs. When we study beams and when we study columns, we will be using this curve, okay? Okay, so, I guess we will wind up this session here. And in the next session, we will look into what do we mean by the characteristic strength of concrete and then what is the tensile strength of concrete and all that stuff.
So, until then, just try to study what we have discussed in this session and you will do good.