← Previous lessonFree lesson 2 of 3 · lesson 2 of 13Next lesson →

Unlock all 13 lessons of Flow Simulation using SolidWorksFull course ₹40,000 · paid

Price & syllabus
Free lesson · 40 min · no payment

Setting Up and Viewing a Pipe Flow Simulation

A free lesson from Skill-Lync's Flow Simulation using SolidWorks course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Simulating flow through a pipe”

What will you learn in this free Flow Simulation using SolidWorks lesson?

The instructor builds a pipe in SolidWorks by sketching, extruding 0.3 m and shelling to 1 mm. He closes the ends with lids, sets up an internal steady flow using the wizard, then refines the mesh and shows velocity on a cut plane with boundary layer growth.

  • Creating a pipe by extrude and shell
  • Lids to make the geometry watertight
  • Wizard choices: internal, steady flow, SI units
  • Cut plane velocity plot and mesh refinement

What comes after lesson 2?

The next free lesson is lesson 3, “Global vs Plot Maximum in Parametric Study Legends” (8 min). Later in Skill-Lync's Flow Simulation using SolidWorks course (paid): lesson 4, Pipe Flow Simulation - performing parametric studies; lesson 5, Transient Flow Simulation of flow over a cylinder; lesson 6, NACA Airfoil simulation. The full course has 13 lessons (3 h 48 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Part 1

Hey guys, I hope you're all doing good. In this video, I'm going to be setting up a pipe flow simulation using SOLIDWORKS flow simulation, okay? The reason why I'm choosing this particular problem is it actually helps you learn a lot about computational fluid dynamics. So to get started, what I'm going to do is I'm going to create the geometry in SOLIDWORKS. There are certain things that you need to do in SOLIDWORKS to run CFD, so in this video, you know, I'll be paying attention to that.

To get started, I'm going to click on the top plane and then I'm going to create a new sketch, alright? So let's create a circle. So in this case, I'm not shooting for a particular geometry. I'm just eyeballing. So as long as it looks like a pipe, I'm good. Now, one thing you can do is after you practice this exercise, you can actually look up for accurate pipe flow geometries for which experimental data exists. You can run the CFD simulations and then compare the results with those experiments.

You know, that's a very nice exercise. And what I'm going to do here is I'm going to click on Extrude and I'm just going to extrude it till 0.3 meters. Again, this is just an arbitrary length that I'm assuming, okay? So that looks like a pipe. Then what I'm going to do is I'm just going to add a small thickness to the pipe. So I'm going to create on Shell and then I'm going to select the top phase and the bottom phase. And let us see, maybe 0.01, 0.001, so 1 mm.

And let's take a look at the preview. That looks okay. So I'm just going to click on that. And that's my pipe, okay? So what I'm going to do now is I'm going to simulate the flow through this. So let us call this guy as inlet and then the other guy as an outlet. Now, when it comes to computational fluid dynamics, we are interested in simulating the flow inside the pipe, okay? So what we need to do is we need to create something called as a computational mesh inside the pipe.

And in SOLIDWORKS, it uses an automatic mesh generation algorithm for which it requires that the entire solid is closed, also called as watertight. So in this particular case, you know, I'm trying to simulate the flow through this pipe, correct? So the bottom, so the top and the bottom faces needs to be closed, okay? And how do you close that? You do that by creating something called as lids. This is specific to SOLIDWORKS. So what I'm going to do is I'm going to go to flow simulation, and you can see that there is this button called create lids.

So I'm going to click on it and make sure that you select the face that you want to close. So in this particular case, I'm selecting this guy. And you can see that it immediately draws this blue color shaded area. Now, that's going to be the inlet of my pipe, okay? You need a closed volume in order to create your mesh successfully. Similarly, I'm going to click on this face, and then these are going to be my two lids, okay? So when you rotate the geometry, you will see that these are closed.

Now, if you pay attention and if you know a little bit about CFD already, then this is like a non-manifold edge. If you don't understand what that is, then don't worry about it. But basically, you need these lids to close the geometry. Now, different CFD codes have different practices, but the concept is you need a closed surface so that you can create the mesh either inside or outside the geometry, okay? Now, once this is done, what I'm going to do is I'm going to set up the flow simulation.

The easiest thing to do next is use the wizard utility. So let's just click on that. It's asking me to save the geometry first, so I'm going to save it. Maybe go to documents. Actually, you know what? I'll save it in a different folder, okay? And I'm going to create a new folder called pipe flow, and let's just call it pipe. Okay, so launch the wizard again. So this helps you set up your CFD problem quite easily, and I'm going to call this pipe flow. With respect to configuration, configuration name, don't worry about it.

We'll figure those out later. You can add comments in case you're interested. So click on next. Unit system, I prefer SI units. If you're used to some other unit system, go for it. Click on next again. So in this particular case, I'm interested in doing an internal flow, right? We are trying to simulate the flow through the pipe and not the flow on top of the pipe, right? If you have to do that, then that would be an external flow simulation. Again, don't worry. We'll be looking at those examples in upcoming videos.

So internal and then consider closed cavities. Don't worry about this option. Leave it at default. We'll talk about this. All right, what are the physical features or what are the additional physics that we want to include in the simulation? Now, remember that in computational fluid dynamics, whenever you include these physics, additional equations or additional terms or the way the equation of the salt gets changed, okay? And we will be looking at those things in upcoming videos as well. So in this particular case, you know, I'm not interested in heat conduction.

So that's not checked. There is no radiation. So that's not checked. There's something called a time dependent, right? So I've not checked that. So what does that mean? So in a pipe flow, the simulation is what is called as a steady flow simulation. That is, after some point in time, your solution is not going to change with time. Now, this might sound a bit funny to you if you have never been introduced to CFD. But the whole idea is, at the end, you get a solution that does not change with time, okay?

And that's what is called as a steady state solution. Now, there are different ways to get to the steady state solution. It depends on how the equations are solved. We will be talking about those things a little bit later because, you know, those are slightly higher level concepts. So you need to know things like time integration or time marching in order to understand those terms, okay? So in this particular case, we are interested in steady flow simulations. And we are not going to include the effect of gravity.

You can do that if you want to. And there's no rotation as well. So rotation is required in case you are trying to simulate something like a centrifugal pump. So moving on, the next thing that I'm going to do is define the fluid that is participating in my simulation. I'm going to be doing a gas flow here. So air is my working fluid. Just click on add so that, you know, it's getting added. Now, in this particular case, the flow type is laminar and turbulent. What does that mean?

Well, you are basically trying to tell SOLIDWORKS what's your flow regime. Now, if the inflow velocity is such that the Reynolds number is greater than 5,000 or 10,000, you know, you can directly use, you know, turbulent only. That is going to kick in the turbulence solver. If you're saying laminar, that means that the Reynolds number is really low. Now, if you're saying laminar and turbulent, then the flow solver is going to be using computational models that are valid for both laminar and turbulent flows. Now, we'll be talking about what these models are in later videos.

But in general, that's the idea. Now, in this particular case, high MAC number flow, not really. I'm not going to do that. I'm just going to click on next. In addition to this, you can also add something called a surface roughness. So, surface roughness is an important parameter that you need to include if, you know, your pipe is made up of something like cast iron. Basically, the pipe is not smooth and hence it's going to cause additional pressure loss, okay? Now, if you include a roughness height, then certain equations are solved which will basically account for this roughness and it would yield an additional pressure loss, okay?

So, for now, I'm not going to touch that. Just click on next. All the thermodynamic properties and parameters, they look fine. Here, you can see that there is velocity parameters. You can initialize the velocity. You can say that at the start of the simulation, the velocity is so and so. But in this case, I'm not doing that. Similarly, turbulence properties. You know, you can set up some turbulence properties. These things can be really important. But for us, we are not going to worry about it. Like I said, these are things that we will slowly learn in the upcoming videos.

Click on finish. And immediately, you can see this box, right? Basically, what SOLIDWORKS is doing is it's calculating something called as a bounding box. It looks at your geometry. It looks at what's the minimum X, maximum X, minimum Y, maximum Y, minimum Z, maximum Z. And then it draws a box around your model. And that's what's happening here. Okay? So, the next thing I'm going to do is, you know, choose boundary conditions. Right-click. And I'm going to type insert boundary conditions. Okay? So, here what we're going to do is we are going to basically say that at this inlet, the velocity is like one meter per second.

So, the first thing I need to do is I need to right-click and then click on select other. And I'm going to select face at lid 2. And then in bracket, you need to see pipe. Okay? Make sure that you do not select this. You know, you need to make sure that you select this. Okay? That is basically saying that at that face, the velocity is going to be one meter per second. So, I'm clicking on that. And here, I'm choosing inlet velocity. And let us say one meter per second.

You're specifying the velocity magnitude here. Okay? And you're not specifying the component of velocity. So, if you have to do a three... Then that will help you specify your XY and Z components. So in this case, I'm just going to do one meter per second. Now, in addition to this, you can subject a fully developed flow profile at the inlet. So as you know, in a pipe flow, the velocity profile is going to look parabolic, right? I can enforce that profile by checking on this box, but I'm not going to do that. I'm just going to say that, you know, the velocity here is one meter per second. So that is what is called as a uniform profile.

And as the simulation progresses, your boundary layer is going to develop and we'll see that in the solution. And in the next phase, you know, let's just click OK here and do the same thing again. This time, I'm going to right click on the other face, click on select other and make sure that you select face at lid one and in the bracket, you see pipe. Okay, so that's the name of your simulation, right? That's the name we gave initially. So you need to see that name.

Okay, whatever the name that you gave, make sure that you see that do not select this option. That's the wrong one. In a later video, you know, I'll comment on why that's the wrong option. So for the outlet, what you need to do is you need to give a different boundary condition. Okay, so at the outlet, what I'm going to do is I'm going to select static pressure. And I'm going to say 101325. Now, if you're a mechanical engineer, then you might know what static pressure is. If you do not know, try to understand what static pressure is and what's the difference between static and total pressure.

Now, with respect to boundary conditions, right? You know, you're solving a partial differential equation, correct? Now, for partial differential equations, you need boundary conditions. Now, the type of boundary conditions that you provide is very important. If you give the wrong boundary condition, then what's going to happen is the simulation is not going to give you the right results. It's going to try its best to get to the solution, but sometimes it doesn't. This is what you say as the solution is not converging. And typically, the solution is not converging because the boundary conditions are wrong or sometimes it has to do with your geometry.

So in this case, you can see that I'm choosing a particular combination of boundary conditions. I'm using mass flow at the inlet and a static outlet. Okay, when I say static outlet, at outlet, I'm providing a static pressure boundary condition. Okay, so that looks good. Let's click OK here. Now, there's another boundary condition that we need to add. And I'm going to just select this guy, the wall. And let me just make this bigger so you can see what I'm selecting. Okay, I'm selecting this guy. And you can see that there's a small arrow there. And I'm going to say that this is a wall.

Now, there are several options. It says it's a real wall or an ideal wall. Okay, so here we are going to basically say it's a real wall. And you can see that there are additional properties such as wall motion. Again, don't worry about these things. We will learn them in upcoming videos. So let's say OK here. And that's basically it. Now, we have almost set up our simulation. The next thing to do is to take a look at the mesh. Now, like I said, SOLIDWORKS uses an automatic mesh generation algorithm.

So what you can actually do is just right click on mesh and it says show basic mesh. Now, you immediately see the cut plane here, which shows you the mesh size. Okay, so this is basically what you call as discretization. And you can see that the discretization along X, Y, and Z direction is the same. So that is why the element looks like a square. It is possible to stretch out the elements if you want to. So in this case, you can also right click and select, not here, sorry.

You can right click on global mesh and click on edit definition. And you can just change this initial level of mesh. And you can see that immediately the mesh becomes finer, right? So if you are using a larger number, you are going to have more mesh points and you can expect an accurate solution. Now, we are going to start with a smaller value. So here you can see that SOLIDWORKS provides us a recommendation. The initial level of mesh is set to 3. This is going to give us a reasonable solution in a reasonable time.

Now, in addition to that, you can do something called as an advanced channel refinement. Now, when I click on that, nothing happens here. But what that does is near the wall of the pipe, it refines the mesh. Now, here what you are seeing is called as an hexahedral mesh. So what does that mean? Now, here you can see that along X, Y, and Z, your mesh looks square, right? Which means in three dimensions, it's going to look like a cube. Now, that is what is called as an hexahedral mesh.

Exahedral meshes can be generated very easily by using something called as a binary tree or an octary data structure approach. Okay. And we'll be talking about these algorithms a bit later. I'm not going to be talking about them in too detail because this is still an introductory class. All right. So now that we have visualized our mesh, let's click on OK. And we're almost set now. So one thing I can do is I can actually run the simulation. And to do that, all I need to do is just press this run button here.

And I'm going to run this thing in parallel. Okay. So I'm going to be using all CPUs. Now, the default option is use all. Now, if you don't have multiple CPUs, that is, if you're using a really old computer, then you will see only this option. So let's click on use all and then click run. And that's going to run the simulation. Okay. You'll see a window like this. You can see that the calculation is going on. About 14 iterations, you know, you get the answer.

Okay. So I'm just going to close this guy. And what I'm going to do now is I'm just going to try and visualize the results. So the first thing I want to do is I want to just hide the computational domain. I don't want to see it. Then I'm going to click on flow simulation. And then I'm going to set up a transparency for the pipe, you know, so that I can see what's going on. The next thing that I want to do is I want to see the mesh inside the pipe.

And the way I can do that is by clicking on results. And then what I'm going to do is I'm going to create a cut plane. So let's click on this cut plane here. Right click. Click on insert. And you can see that, you know, this is the XYZ plane that I'm selecting. And you can see that this green plane is basically cutting the pipe right in the middle, right? That's exactly what I want. And we are going to display some contours. What are we going to look at?

Let's look at velocity first. Velocity magnitude. And I'm also going to be looking at the mesh because we want to see how the final mesh looks like. And the mesh is going to be colored in black. And let's click on OK here. There you go. You can see that you have a very funny looking simulation, but that's fine. OK. The mesh is really coarse. And what's happening is, you know, you can see that initially the velocity is all uniform. Let me just put this in straight view.

The velocity is initially uniform, but then there's something that is close to what you would call as a boundary layer. And that's going to make the mesh look more parabolic. All right. Now, again, this simulation is a fairly coarse simulation. And it looks like it did not do the channel refinement that I expected. So let me do something else here. Click on Edit Definitions. And what I'm going to do is I'm just going to refine the mesh maybe two levels more. And I'm just curious why it did not do the advanced channel refinement.

That's OK. So let's click on OK now. And let's run the simulation one more time. I'm running this as a new calculation. I'm clicking on Run. You can see that it's doing the mesh. I had about 25,000 mesh elements initially. And when I click on this information button, I can see all the details. You can see that we are running at 19th iteration. Things are a bit slow because now there are more cells. All right. Perfect. So the solver is finished. So let's close this guy.

OK. So when I click on Show again this time, you know, things look much more interesting. All right. So I'm going to select this guy, Edit. Maybe what I'm going to do is just increase the maximum to 2.5. Actually, the maximum velocity is 1.3. So I'm going to set it to that. And let us see. For the color palette, I'm going to just increase the number of levels to maybe 15. Click OK. Yes. That looks much better. And I believe the flow comes like this. Yes.

No. Actually, the flow comes from left to right. Sorry about that. So you can see that the initial velocity profile looks uniform, basically, along the x direction. OK. So if you look here, along the x-axis, the velocity is given the same color, right, which means it's uniform. And as I move from left to right, you see the boundary layer appearing. And then you are getting this parabolic profile. So the next thing that we are going to do is we are going to make some line plots and look at this parabolic profile and get some results out of it.

OK. So and I'll be doing this in the next video. I hope you enjoyed this video. If you have any questions, post them in the comment section. I would be happy to answer them for you. All right. I'll see you guys in the next video. Bye.

Part 2

दोस्तों, मुझे आशा है, आप सभी अच्छा कर रहे होंगे. इस वीडियो में, मैं SOLIDWORKS Flow Simulation को उपयोग करके, एक Pipe Flow Simulation स्थापित करने जा रहा हूँ. इस विशेश टॉपिकल को चुनने का कारण ये है, जिससे कि आप Computational Fluid Dynamics के बारे में काफी कुछ जान पाएं. तो आरम करने के लिए मैं SOLIDWORKS में Geometry बनाने जा रहा हूँ. CFT को चलाने के लिए कुछ चीजें हैं जो आपको SOLIDWORKS में करने के आवशकता है. इसलिए इस वीडियो में मैं उस पर ध्यान दूँगा. शुरू करने के लिए मैं पहले Top Plan पर क्लिक करूँगा और फिर एक नया Sketch बनाऊँगा. तो एक Circle बनाते हैं. इस Case में मैं किसी विशे� रहा हूँ. अब एक चीज जो आप कर सकते हैं आप वास्ता में Accurate Pipe Flow Geometrics के तलाश कर सकते हैं. जिसके लिए प्रयोगिक डेटा मौदूद है. आप CFD Simulation रन कर सकते हैं और फिर उन प्रयोगों के साथ परिनामों के तुलना कर सकते हैं. अब जानते हैं कि यह बहुत अच्� जिसमें मान रहा हूँ. तो यह एक pipe के तरह दिखने लगा. फिर मैं बस pipe में छोटी मोटाई और जोडने जा रहा हूँ. इसलिए मैं एक shell बनाऊंगा और फिर मैं उपरी सतह और निचली सतह का chain करूँगा. हम देखते हैं शायद 0.001 जो होगा 1 mm. आईए review देखें. जो ठ के माध्यम से flow का simulation करूँगा. तो आईए हम इसको inlet कहते हैं और दूसरा एक outlet है. अब जब computational fluid dynamics की बात आती है तो हम pipe के अंदर flow का simulation करेंगे. तो अब हमें pipe के अंदर एक computational mesh जैसा कुछ बनाने के अवशकता है. SOLIDWORKS में यह एक automatic mesh generation algorithm का उप्योग करता है. इसके लिए यह आव� इस pipe के माध्यम से flow का stimulation करने के कुशिश कर रहा हूँ. तो निचली सता के top को बन करने के अवशकता है. ठीक है. और आप इसे कैसे बन करते हैं? आप कुछ ऐसा बनाते हैं जिससे lids कहा जाता है. यह SOLIDWORKS के लिए बहुत विशिष्ट है. तो मैं flow simulation करने जा रहा हूँ और आप देख सकते हैं कि यह create lids नाम का button है. इसलिए मैं उस पर click करूँगा और सुनिश्चित करूँगा कि आप उस face का chain करें जिसे आप बंद करना चाहते हैं. इस case में मैं इसका chain कर रहा हूँ और आप देख सकते हैं कि यह तुरंट इस नीले रंग के shaded area को draw कर रहा है. अब यह म मेरे pipe का inlet होने जा रहा है. सफलता पूर्वा के एक mesh बनाने के लिए आपको एक closed volume क्या वशक्ता होती है. इसी तरह मैं इस face पर click करूँगा. अब यह मेरे दो lids हो गए. जब आप geometry को घुमाएंगे तो आप देखेंगे कि यह बंद हो गए है. यदि आप पहले से ही CFD के ब क्या है. तो इसके बार में चिंता ना करें क्योंकि आपको जबंद करने के लिए इन lids के अवशक्ता है. अब विभिन CFD code में अलग-अलग processes हैं. लेकिन main concept यह है कि आपको एक closed ताकि आप geometry के अंदर या बाहर mesh बना सकें. एक बार यह पूरा हो जाने के बाद मैं flow simulation स्था� करें. तो बस उस पर क्लिक करें. यह मुझे पहले geometry को save करने के लिए कह रहा है. इसलिए पहले मुझे save करूंगा. अब हम dark command पे जाते हैं. दर असल मैं एक नया folder मनाने जा रहा हूँ. जिससे pipe flow नाम देते हैं. चलो इसे pipe के. ठीक है. अब फिर से wizard launch करें. तो यह आपकी CFD स हमस्य को काफी आसानी से स्थापित करने में हमारी मदद करेगा. मैं configuration के संबन में से pipe flow कहूंगा. configuration नाम के बारे में ज़्यादा चिंता ना करें. हम बाद में उनका पता लगाएंगा. यदि आप interested हैं तो आप comments जोड सकते हैं. तो अगली unit system पर click करें. मैं SI unit को प्राश्मि simulation करने के कोशिश कर रहे हैं. पाइप के ऊपर के flow को नहीं. अगर आपको ऐसा करना है तो वह external flow simulation होगा. चिंता ना करें. हम आगे दूसरी वीडियो में नुदाहरणा को देखेंगे. इसलिए internal और फिर closed activities पर विचार करें. इसे default पर ही छोड़ दें. हमने इस बारे में बा dynamics में. जब भी आप इन physics को शामिल करते हैं. अतिरिक्त समीकरन या अतिरिक्त शब्द या salt के questions बदल जाते हैं. हम आने वाले वीडियो में भी उन चीज़ों को देखेंगे. इस case में heat conductivity की जाच नहीं कर रहा हूँ. क्योंकि यहां कोई radiation नहीं है. इसे आप time dependent कह सकते हैं. त आपको कभी CFD के बारे में जानकारी नहीं है. लेकिन concept यह है कि अंत में आपको solution मिलता है जो समय के साथ बदलता नहीं है. यही एक steady state solution के रूप में कहा जाता है. steady state solution प्राप्त करने के विभिन तरीके हैं. यह इस बात पर निर्फर करता है कि समीकरन कैसे हल होते हैं. हम थो या time marching ताकि उन terms को समझा जा सके. इस case में हम steady flow simulation के बारे में बात करेंगे. हम effect of gravity को शामिन नहीं करने जा रहे हैं. आप ऐसा कर सकते हैं यदि आप चाहते हैं. और साथ ही को rotation नहीं है.

rotation के यह आवश्यक्ता तब होती है जब आप एक centrifugal pump की तरह कुछ अनुकरन करने की कोशिश कर रहे हैं. तो अब simulation का उभ्योग करने वाले द्रव को परिभाशित करते हैं. यहां मैं gas flow के बारे में बात कर रहा हूँ. यहां air मेरा working fluid है. बस add पर click करें ताकि add हो सके. इस case में laminar और turbulent flow type है. इसका क्या मतलब है? आप mood roof से SOLIDWORKS को बताने की कोशिश कर रहे हैं कि आपका flow rhythm क्या है. यदि in flow velocity ऐसा है कि renoid संक्या 5000 या 10,000 से अधिक हैं तो आप सीज़े turbulence का उप्योग कर सकते हैं. तो यह turbulence solver में जाएगा. यदि आप laminar select कर रहे हैं तो इसका मतलब है कि व flow solver computational models का उप्योग करेगा जो laminar और turbulence दोनों flow के लिए मानने हैं. हम इन modelों के बारे में बात के वीडियो में बात करेंगे. इस case में high mac number flow वास्ता में नहीं है. मैं ऐसा नहीं करने जा रहा हूँ. मैं next पर click करने जा रहा हूँ. इसके अतरिक आप एक surface roughness नामा कुछ भी जो हुआ है. surface roughness एक महत्वपूर्ण parameter है जिसे आपको शामिल करने के अवशकता है. और यदि आप जानते हैं कि आपका pipe gas time के तरह किसी भी चीज़ से बना हुआ है. असल में pipe smooth नहीं है. और इसलिए यह अतरिक प्रेशर लॉस के कारण बन सकता है. यदि आप roughness height शामिल करते ह हैं तो कुछ समिकरन हल किये जा सकते हैं. जो mole root से इस roughness के लिए जिम्मेदार होंगे. और यह एक अतरिक प्रेशर लॉस के कारण होगा. इसलिए अभी के लिए मैं उसे चूने नहीं जा रहा हूँ. बस next पर click करें. सभी thermodynamic feature और parameter वे ठीक दिख रहे हैं. यहां आप देख स कर सकते हैं कि velocity parameter है. आप velocity को initialize कर सकते हैं. आप कह सकते हैं कि simulation के शुरुवाद में velocity इतने पर है. लेकिन case में, इस case में मैं ऐसा नहीं कर रहा हूँ. इसी तरह आप कुछ turbulence properties भी रख सकते हैं. यह बाते वास्ता में मर्जपूर्ण हो सकती हैं. लेकिन हम इसके बारे में चि देख सकते हैं. असल में solid box क्या कर रहा है? यह एक bounding box के रूप में कही गई चीज की calculation कर रहा है. यहाँ वही हो रहा है. अब boundary conditions चुने right click करें और insert boundary condition पर click करें. यहाँ इस inlet पर velocity एक meter प्रति सेकेंड की तरह है. इसलिए पहली चीज़ जो मुझे करने के ज़रूरत है वह है right click और फिर select others पर click करने के आवशकता है. यहाँ face at the rate face at the rate leads to select करें और फिर देखें कि bracket में pipe लिखा है. आपको यह सुरिश्चित करने के आवशकता है कि आप इसी का chain कर रहे है. यह मूल रूप से कह रहा है कि उस चरण में velocity एक मीटर प्रति सेकेंड होने जा रहा है. मैं उस पर click कर रहा हूँ और यहाँ मैं inlet velocity चुन रहा हूँ. जो है एक मीटर प्रति सेकेंड. आप यहाँ velocity magnitude specify कर रहे हैं. आप velocity component को specify नहीं कर रहे हैं. यहीं आपको एक 3D वेक्टर बनाना है तो वो आपको अपने x, y और z component को specify करने में मदद करेगा. इस case में मैं 1 meter per 30s करने जा रहा हूँ. इसके अलावा आप inlet पर fully developed flow profile कर सकते हैं, तो जैसा कि आप जानते हैं, pipe flow में velocity profile parabolic की तरह दिखता है. मैं इस box को चेक करके उस profile को लागू कर सकता हूँ, लेकिन मैं ऐसा नहीं करने जा रहा हूँ. मैं बस ये कहने जा रहा हूँ, कि यहाँ velocity 1 meter per 30s ह इसलिए इसे एक uniform profile कहा जाता है. जैसे जैसे simulation आगे बढ़ता है, आपकी boundary layer विक्सित होती जाती है, और हम इसे solutions में देखेंगे. अगले चरण में यहाँ ok पर click करें, और फिर से वही काम करें. इस बार मैं other face पर right click करूँगा, select others पर click करूँगा, और सुनिश्चित करें कि आप face at lid 1 का chain कर रहे हैं, और bracket में आप pipe लिखा हुआ देख रहे हैं, यह आपके simulation का नाम है, यही नाम हमने शुरू में दिया था, तो आपको यह नाम देखने के जरूरत है, जो भी नाम आपने दिये हैं. सुनिश्चित करें कि आप वह देखते हैं, इस विकल्प का chain ना क करें, यह गलत है, बात के वीडियो में मैं इस बात पर टिपनी करूँगा कि यह गलत विकल्प क्यों है, तो आउटलेट के लिए आपको क्या करने के आवशकता है, आपको एक अलग boundary condition देने के आवशकता है, आउटलेट पर मैं static pressure का chain करने जा रहा हूं, जो कह सकते हैं, ए एक शुन्य एक तीन दो पांच है, यदि आप एक mechanical engineer है, तो आप जान सकते हैं कि static pressure क्या है, यदि आप नहीं जानते हैं, तो समझने के कोशिश करें कि static pressure क्या है, और static और total pressure के बीच क्या अंतर है, अब boundary conditions के सम्बंद में, अब partial differential equation के लिए आपको boundary conditions के आवशकता है, आपक simulation आपको सही प्रणाम नहीं देने वाला, यह solution के लिए अपनी पूरी कोशिश करता है, लेकिन कभी-कभी ऐसा नहीं होता है, यह वही इस्तिती है जब आप कह सकते हैं कि solutions converging नहीं है, आमतर पर solutions converging नहीं होता है क्योंकि boundary conditions गलत होती है, या कभी-कभी से geometry के साथ करना पड� इसमें आप देख सकते हैं कि boundary conditions का एक विशेश combination में चुनने जा रहा हूँ, मैं inlet और एक static outlet पर mass flow का उपयोग कर रहा हूँ, मैं यहां static pressure boundary conditions प्रवाइड कर रहा हूँ, यहां OK क्लिक करें, अब एक और boundary condition है जिसे हम जोडने के अवशकता है, अब एक और boundary condition है जिसे हमें जो अब देख सकते हैं कि यहां एक छोटा arrow है और यह एक दिवार है, अब यहां कई भी कल्ब है, उसके अनुसार यहा एक real wall यहा एक idea wall है, यहां हम कह सकते हैं कि यहा एक real wall है, आप देख सकते हैं कि अधरック options हैं, जैसे कि wall motion 1, sorry, जैसे कि wall motion, इन बातों के चिंता मत करो, इन ब in the video.

Here we go. Now we have our simulation set. Now we have mesh. I have said that SOLIDWORKS and Automated Machinery Algorithm What can you do? What can you do? We have right-click and it is called Show Basic Mesh. Now we have cut-plane which shows the mesh which shows the mesh which you can see in the lower end. You can see that Discriterization You can see that X, Y and Z discretization is equal to 1. This means this has an element to a square. If you want to stretch your elements and then you can check it and go in this case to edit definition and also put it सकते हैं और आप केवल मेश के इस प्रारम्फिक स्तर को बदल सकते हैं और आप देख सकते हैं कि तुरंद मेश और ज्यादा फाइन हो जाता है यदि आप बड़ी वैल्यू का उप्योग कर रहे है तो आप के पास अधिक मेश पॉइंट्स होंगे और आप एक सटीक समाधान क meet कर सकते हैं हम एक छोटे value के साथ शुरू करने जा रहे हैं यहां आप देख रहे हैं कि SOLIDWORKS हमें recommendation प्रदान कर रहा है यहां mesh का प्राराम्पिक स्तर तीन तक set है यह हमें एक उचित समय में एक उचित समाधान देने जा रहा है इसके लावा आप advanced channel refinement कर सकते हैं जब मैं उस पर click करता हूँ तो यहां कुछ भी नहीं होता है लेकिन यह क्या करता है pipe की दिवार के पास यह mesh को refine करता है और आप जो देख रहे हैं उसे hexahedron mesh कहा जाता है इसका क्या hedron mesh को binary tree या octra data structure की मदद से बहुत आसानी से बनाया जा सकता है हम इन algorithm के बारे में बाद में बात करेंगे मैं उनके बारे में विस्तार से बात नहीं करने जा रहा हूँ क्योंकि यह अभी एक introductory option है यदि आपके पास एक से अधिक CPU नहीं है तो आप वास्ता में पुराने computer को प्योग कर रहे हैं तो आपको केवल यह विकल्प दिखाई देगा तो use all पर क्लिक करें और फिर run पर क्लिक करें जिससे simulation चालू हो जाएगा आप इस तरह का एक window देखेंगे आप देख सकते हैं calculation लगबग 49 iterations पर चल रही है आप देख सकते हैं कि calculation लगबग 49 iterations पर चल रही है आपको जवाब मिल जाता है मैं बस उसको बंद करने जा रहा हूँ अब मैं केवल result को visualize करूँगा पहली चीज जो मैं करना चाहता हूँ मैं सिर्फ computational domain को height करना चाहता हूँ मैं इसे नहीं देखना चाहता फिर मैं flow simulation पर click करूँगा और फिर मैं pipe के लिए एक पारदरशिता स्थापित करने जा रहा हूँ ताकि मैं देख सकूँ कि क्या चल रहा है अगली चीज जो मैं करना चाहता हूँ मैं pipe के अंदर mist देखना चाहता हूँ यह मैं deserts पर click करके देख सकता हूँ और अब मैं cut plane मनाऊँगा यहां इस cut plane पर click करें right click करें insert पर click करें और आप देख सकते हैं कि यह x y z plane है जिसे मैं select कर रहा हूँ यह green plane pipe को काट रहा है ठीक बीच में यही मैं और अब देखते हैं कि final mesh कैसा नजर आता है mesh काले रंग का होने जा रहा है यहां ok पर click करें आप देख सकते हैं कि आपके पास एक बहुत मज़ेदार दिखने वाला simulation है लेकिन यह ठीक है mesh वास्ता में मोटे हैं और आप देख सकते हैं कि शुरू में velocity सभी एक समान है फिर से ही है simulation काफी हद तक काफी मोटे simulations है और ऐसा लगता है कि यह channel refinement नहीं किया गया है जिसकी मुझे उम्मीद थी इसलिए मुझे यहां कुछ और करना होगा edit definition पर click करें और mesh को refine करें करीब दो level तक और मैं advanced channel refinement के लिए उत्सुक हूँ अब ok पर click करते हैं आए simulation को एक बार और run करें मैं इसे एक नई गणना के रूप में चला रहा हूँ run पर click कर रहा हूँ आप देख सकते हैं कि यह mesh कर रहा है मेरे पास शुरू में लगबग 25,000 mesh elements थे और जब मैं इस information button पर click करता हूँ तो यह सभी विवरन देख सकता हूँ हम 19 वी iteration पर है थोड़ी चीज़े थोड़ी धीमी है क्योंकि shells बहुत अधिक है solver खत्म हो गया है तो इसको बंद करें जब मैं show again पर click करता हूँ तो इस बार चीज़े बहुत अधिक दिल्चस्प लगती है तो इसको select करने जा रहा हूँ एडिट करता हूँ अधिक्तम 2.5 तक बढ़ाएं वास्तम में अधिक्तम velocity 1.3 है एक दिल्चस्प लगतीन है तो मैं उसे उस पर set करूँगा और color palette देखूँगा मैं केवल level के संक्या बढ़ा कर 1.5 करने जा रहा हूँ ओक्के पर click करें यह बहुत बहतर लग रहा है और मेरा मानना है कि flow इसी तरह आता है दर असल flow बाएं से दाएं आता है अब देख सकते हैं कि प्रारंभिक velocity profile mood रूप से x दिशा में समान दिखती है यह दिए आप यहा जैसे ही मैं वाएं से दाएं के तरफ जाता हूँ boundary layer दिखाई देते हैं और फिर आपको यह एक parabolic profile मिल रहा है हम कुछ line plot बनाएंगे और इस parabolic profile को देखेंगे और इसके कुछ परिणाम प्राप्ट करेंगे हम यह अगले वीडियो में करेंगे मुझे अमीद है आपको यह � पसंद आया होगा यदि आपके पास कोई प्रश्ण है तो उन्हें comment section में post करें मुझे आपके लिए इसका जवाब देने में खुशी होगी अगले वीडियो में आप लगों से फिर से मिलूगा तब तक बाई

Want the rest of Flow Simulation using SolidWorks?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Flow Simulation using SolidWorks course

The remaining 10 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Flow Simulation using SolidWorks course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.