← Previous lessonFree lesson 2 of 3 · lesson 2 of 34Next lesson →

Unlock all 34 lessons of Electric Motor Design using MATLAB and ANSYS MaxwellFull course ₹40,000 · paid

Price & syllabus
Free lesson · 20 min · no payment

Electric Motor Design Process and Magnetic Basics

A free lesson from Skill-Lync's Electric Motor Design using MATLAB and ANSYS Maxwell course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Electromagnetics Week 1 Session 1”

What will you learn in this free Electric Motor Design using MATLAB and ANSYS Maxwell lesson?

The instructor surveys where electric motors are used, the motor types in the course, and the tools, ANSYS Maxwell and MATLAB Simulink. He walks through the design flow from sizing to optimisation and testing, then starts electromagnetics with hysteresis, saturation, flux linkage and back EMF.

  • Motor types and where they are applied
  • Design flow: sizing, CAD, FEA, optimisation, testing
  • Hysteresis loop, saturation and residual flux
  • Flux linkage as N times flux, and back EMF

What comes after lesson 2?

The next free lesson is lesson 3, “Maxwell's Equations, Toroid Examples and Magnetic Circuits” (17 min). Later in Skill-Lync's Electric Motor Design using MATLAB and ANSYS Maxwell course (paid): lesson 4, DC Motors Week 2 Session 1; lesson 5, DC Motors Week 2 Session 2; lesson 6, DC Motors Week 2 Session 3. The full course has 34 lessons (9 h 54 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello everyone, this is week one. We're going to start with the basics of electromagnetics, but before we jump in into the course, I'm going to give you a little bit of introduction of what electric motor design is, how it is being used in the industry right now, in different industries right now, and then how we're going to plan the course for the rest of the weeks, and then we'll kind of get into the basics of electromagnetics throughout the end of this week's course. So to start with, electric motor is a very evolved design. It's being used in automobiles and industrial machine tools from at least over three to five decades. They have evolved so much. You can almost see an electric motor in almost every application that you come across in your day-to-day life, starting from your fan, all the way to the washing machine, or even the car that you drive, or an electric bike.

Obviously, the most popular ones nowadays are drones and electric aircraft. Almost everything has electric motor propulsion system that gives the traction for the wheels. There are different types of electric motors. The basic one is DC motor. It just needs 24 volts or 10 volts, depending on the speed that you need. And then, they're very simple in operation. They have really basic principles. We're going to look at different types of DC motors in this course. There's an induction motor, which has been used in the industry from at least last three decades. It is very popular, very efficient. Of course, there are some limitations with respect to how much torque they can produce.

And that's why permanent magnet motors have evolved, beating the efficiency and higher torque densities that are being demanded by latest automobiles and cutting-edge industrial machine tools. Some of the examples of automobiles, as you know, Tesla is purely an electric vehicle. There's just around 480 HP electric motor that powers the whole car. It's a pretty advanced and really efficient electric motor that's being used in Tesla Model 3, or more or less. Anything you can take. Electric bikes, on the other hand, have drives and electric motors providing that traction for the rear wheel.

Most of the electric bikes are designed in such a way where you can really pedal it, but it's going to power the battery, which in turn is going to power the electric motor that's being installed in the electric bike that will provide you traction. One of the electric vehicles that I came across is Meyer Motors, which is a very local United States, Ohio design, which is a fact that you can almost build an electric car by yourself. It's a very small company. It's a very small company. It's almost like it probably has market in just one state in the United States.

Industrial machine tools, on the other hand, have slightly different applications of electric motors. Several electric motors work together. For example, you have an electric motor that moves a particular system in X direction, and then you have an electric motor that moves the same system in Y direction, and then you can have an electric motor that moves the same system in Z direction. Eventually, all three axes have to be coordinated. It's called multi-axis motion control. It's very popular in industrial machine tools, such as any CNC machine.

You can also picture something like a laser cutting machine or a mill, for example. All of these have electric motors that work together. So each motor has knowledge of what's going on with the other motor, which is running in a different direction. Automation, on the other hand, is material handling. All these machines need some of the parts being moved within the factory or within the manufacturing facility. Automation, which includes auto-guide robots, or it could just be part-picking and placing, part-sorting. Some of them include vision systems as well.

So that comes under automation technologies. So in this course, we're going to learn about next-generation electric motor designs, which can provide higher reliability, higher efficiency, and lower cost. These will be our design objectives when we start looking at next-generation electric motor designs. This course tries to give you a good understanding of each motor design that we have seen here in applications such as automobiles and industrial machine tools. As we move forward in the weeks, you'll get a good flavor of how you can realize the numerical model of an electric motor to provide best efficiency or torque in applications where higher endurability is required.

So in this course, we'll mainly use ANSYS Maxwell and MATLAB Simulink. The idea of using these two tools is to give you guys a good experience of what tools are being used in the industry at this point. This will give you a great platform to learn the tool, apply it on a problem that is solved by a lot of industrial professionals. So by the end of this course, you'll be as skillful as probably some of the application engineers at ANSYS who would have some basic knowledge on electromagnetic analysis, right?

Not obviously to a level where you master everything in the software, but you'll know enough tools to start electric motor design from scratch, build it on your own, and then simulate it, analyze the results, do post-processing of the results, troubleshoot a few issues. Similarly, you'll also learn some mathematical equations that you would need to understand the electric motor design. We will develop them in MATLAB Simulink, put together these equations into the actual motor design, and then see the torque speed characteristics, how different kinds of input affect your actual torque output of the electric motor.

So I wanted to kind of give a basic flow of electric motor design process. The first part of electric motor design is sizing, right? So you need to start looking at what is my size, where can this motor fit, what are the power requirements, and how can I size an electric motor that fits into that power versus size. So you look at the outer dimensions, and you look at the inner diameter, and then you look at the overall volume you have. Once you have that data, then you'll start looking at what is the load torque, like, I mean, what am I trying to move using this motor, right?

And what speeds should I be going at? Once you have them, then you figure out the efficiency that your motor should provide. And then obviously, depending on the application, there's a limitation on the input power that you can give. So you get all these parameters sorted, the specifications are the really most important part of any design. So if you aim to become a design engineer, you need to learn the basics of how you write specifications, how you demand specifications from your product management team, and that's how you can start designing an efficient product.

CAD and FEA. So once you have these requirements, then you start a CAD design. A lot of mechanical engineers are really good at CAD design. So once you have product specifications, you work with the mechanical engineers to draw a CAD design. And then once they have a CAD design ready, then you import that CAD design into one of those FEA tools, such as ANSYS. Once you have FEA model ready, then you start doing multiphysics analysis. So multiphysics analysis is electromagnetic analysis, structural analysis, thermal analysis, because an electric motor that you design is not only designed to survive in an electromagnetic environment, it has to survive different types of temperatures, different types of altitudes, and all that stuff.

So you need, it's really important to do structural and thermal analysis on your motor designs so that they're structurally stable and thermally endurable over a period of time when it's trying to continuously operate at its rate of torque. It's also really important to understand the numerical analysis part of it, just for the fact that are you still designing your electric motor mathematically correct? Symmetry is really important in motor designs, so you need to understand the basics of Maxwell's equations, motor equations in general, to make sure the electric motor that you design, whatever design you come up with, still satisfies all the physics and math.

Once you have a good design that's ready to be considered as a prototype, the most important thing before fabricating it is optimization. There can be a lot of fine tuning that can be done for the electric motor design that you came up with. For example, let's say you want a 20 Nm output torque, but the motor design that you came up with is only providing 15 Nm. There are several optimization techniques that you can use, such as differential evolution or genetic algorithm. They will help you parameterize a set of parameters, such as, let's say, the inner diameter or outer diameter.

Give them a range from like 10 to 15 Nm, and 15 Nm is your maximum size. It's going to solve, the math and algorithm is going to solve, to give you maximum torque, minimum torque ripple, maximum efficiency, because you already defined these are your constraints that you want to solve it for. So once you do that, that's fine tuning your motor design, then your design is. Finally ready to be prototyped. After prototype, once you have an alpha prototype, you test it on a Dynamo setup, apply different loads on it, make sure you got the performance that you saw in your finite element analysis results.

Once everything is validated, it's also important to understand that the motor design you came up with can be mass produced or it's easy to manufacture, right? So once you have everything done, at that point, your motor is ready to be produced in bulk or if it's ready for production, pretty much. In this course, obviously, we'll have a set of data that's already out there. We're going to design an FEA model, do some analysis, and then we'll also look at a few optimization techniques, how we can use them.

But mainly this course is totally focused on electromagnetic analysis, finite element analysis, and numerical analysis. So we'll do a couple of projects based on them. This will give you the core aspect of electric motor design, because the first part of this, designing electric motors on the last part of it, you'll have support in your team, such as product engineers or mechanical engineers, product management teams. They'll help you get the other data. But as an electromagnetics engineer, you will be the expert in these areas. So getting to know these basics and how to use them to solve industrial level problems will be something that we'll discuss in this course.

There is also some iterative process between them. Sometimes your optimization might not give you the best results. So you might have to go back to your CAD model, make some tweaks, redo some initial finite element analysis, and then do optimization again. It is almost like an iterative process. That's why it's challenging, and that's why we are electrical engineers. So what is electromagnetics? The basic term that comes up when you start discussing about electromagnetics is flux density. So what is flux density? It is just a vector quantity.

The way I would like to think about flux density is, so you have sand. When you pick some sand in your hand and try to drop them, you see sand being all these sand particles. You see how dense they are, and then as you release all the sand out of your hand, you can see how less dense they become, right? So if you look at all those sand particles, and then the path that they are traveling from your hand to the ground, so that's, when you look at it, that's how flux lines travel from a high density point to a low density point.

And that's your flux density, like number of sand particles per unit area is the sand density. If you think about it in magnetic flux, that's your flux density, right? You just, that's the beauty of electromagnetics. You cannot really see it, but you know it. Magnetic field. A lot of times people get confused between flux density and magnetic field. So flux density is, as I said, flux lines per unit area. Magnetic field is how much current you are applying to get that flux, right? So flux density, let's say that's magnetic.

You need electrical stuff that produces magnetics, right? So the thing that produces it is called magnetic field or magnetic field intensity, right? So ampere per meter is the unit, which says current per unit distance, right? That's how I would remember that. It's a vector, but magnetic field produced by a field source, or is it current moving through a wire or a permanent magnet? So what is magnetization? So magnetization and magnetic field are pretty close terms. Both have ampere per meter, but magnetization determines the state of that material.

It is the resultant sum of individual atomic magnetic moments per unit volume. So again, going back to the same sand example, when you're releasing sand from your hand, you can see all those sand particles falling right in the same direction towards the ground, right? They don't go up. They don't go sideways. Flux lines are exactly like that. When they are all aligned in a particular direction, that's how you know that particular material has become magnetized. That's measured by magnetization. So in total, magnetic flux density can be written as permeability multiplied by intensity plus magnetization.

Magnetic permeability of free space is equal to 4 pi multiplied by 10 power minus 7. It's called a permeability constant, but the free space, it's always constant. For different materials, there will be a relative magnetic permeability that you would need to consider. For air, it's 1. For different materials, you'll have different magnetic permeabilities. So what is magnetic hysteresis? I have a small graphic here that gives you guys a good idea on what it means to magnetize and what it means to hysteresis, right? So if you look at this curve, when it started, when it started magnetizing, it got saturated at some point, which is called saturated flux density, right?

So at that point right there, it got saturated. What does it mean by saturation? So saturation is a point at which the magnet is magnetized. At that point, when you try to reverse the magnetic field, like, for example, you applied some electrical field, you saw a flux density, and it got saturated for that material. When you try to demagnetize it or apply a negative field, it's never going to come back to its zero spot because that's the quality or the nature of magnetic materials. It's going to come back in a curve that flows like this, which is the magnetization curve or magnetic hysteresis curve.

So the nature of a magnetic material is never the same when it's, so it's highly nonlinear, meaning their response to a stimulus lags in a repeatable manner. Since the material is consistent, you'll start seeing the same pattern, but it's just not going to come back to its initial magnetization value. So large hysteresis loop would mean hard magnetic materials. You should also understand that hysteresis loop is not reversible, as I said, because the material is magnetized. Energy product for any particular material is calculated using B multiplied by H.

So B is magnetic flux density. H is applied magnetic field or applied electrical field. The saturated or the flux density that the magnetic material is going to retain is called residual magnetization. So the next most important term that you need to understand are flux linkage and back EMF. When you start looking at flux linkage, you have to understand Faraday's law. So whenever you see phi, it's magnetic flux lines or flux, right? What did I say? Like flux or sand, number of sand particles is in a particular area, right?

So if you look at number of flux lines, it's your integration of flux density in a specific area. So flux lines is B multiplied by A. B is your flux density. A is your unit area. So you can always look at it like B, A. But flux linkage, let's say you have a coil now, a string, for example, it's N phi because you have flux lines flowing through several strings, right? So that number of strings or number of turns is denoted by N multiplied by the number of flux lines, or it can be written as NBA.

So this multiplication will give you flux linkage. So now what is EMF? EMF is electromotive force. So you have to start looking at EMF as a voltage, right? Wherever there is a potential difference, there will be a voltage, right? So EMF is D phi or DX, which means number of flux lines or change of flux lines or change in that area, right? It has a negative sign on it, so it's very important to understand why there is a negative sign on it. So Lenz's law explains the direction of force.

So that negative sign came from Lenz's law. So Lenz has done a lot of research on identifying what direction of force is developed when there is a flux applied in a certain direction. It has been found out that it will be in a negative direction. So if you apply flux in a specific direction based on your angle, it will be the electromotive force will be in the negative direction of that. So Maxwell-Farad equation, we'll talk about this a little bit in the next slide, but Maxwell-Farad equation is just trying to say a time-varying magnetic field has time-varying electric field.

Although this sounds really simple, it has a lot of meaning in it. A time-varying magnetic field will have a time-varying electric field, vice versa. So if you send a current which is time-varying, for example, a sinusoidal current, you'll start seeing a sinusoidal magnetic field, right? So there are four really important Maxwell equations. Let's take a quick break and come back.

Want the rest of Electric Motor Design using MATLAB and ANSYS Maxwell?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Electric Motor Design using MATLAB and ANSYS Maxwell course

The remaining 31 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Electric Motor Design using MATLAB and ANSYS Maxwell course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.