← Course overviewFree lesson 1 of 3 · lesson 1 of 44Next lesson →

Unlock all 44 lessons of Design of Steel Superstructure in BridgesFull course ₹40,000 · paid

Price & syllabus
Free lesson · 30 min · no payment

Introduction to Bridges: Components, Load Transfer and Classification

A free lesson from Skill-Lync's Design of Steel Superstructure in Bridges course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 1”

What will you learn in this free Design of Steel Superstructure in Bridges lesson?

Welcomes learners to steel bridge design and says who the course suits, mainly structural, civil and some mechanical engineers. Covers what bridges are, how loads transfer through components, how bridges are classified by material, purpose, behavior and span, and a short history from cast iron to prestressed concrete.

  • Who the course is for and what it covers
  • How bridges are classified by material, purpose and span
  • Compression, flexure and tension behavior of bridge types
  • Brief history from cast iron to prestressed concrete

What comes after lesson 1?

The next free lesson is lesson 2, “Bridge Types by Span: Arch, Girder, Truss and Cable-Stayed” (16 min). Later in Skill-Lync's Design of Steel Superstructure in Bridges course (paid): lesson 4, Week 2 Session 2; lesson 5, Week 3 Session 1; lesson 6, Week 3 Session 2. The full course has 44 lessons (15 h 38 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello all. Welcome to the course, Design of Steel Superstructure Bridges. In this course, mostly we'll be learning about design of steel superstructures, which includes design of steel girder bridges and steel truss bridges, steel composite bridges, which also includes some parts of concrete elements in it. And in addition to it, we'll be also learning some elements of the steel substructures. They're generally called truss and they're mostly provided in pedestrian foot bridges. And in very few cases, they are also used in vehicle bridges, including rail or also in road bridge.

And next, we'll be coming to who this course will be very suitable for. This course is really suitable for structural engineers who intend to choose their career as bridge engineers and also to civil engineers who intend to do the same, choose their career as bridge engineer. In quite a few cases, mechanical engineers also practice the profession of bridge engineering. Since the course is somewhat very similar, coursework what they learn is very similar to what civil engineers also learn. It is mostly about calculation of stresses, then also the geometric imperfection. That also includes function.

So in this session, we'll be covering one day about the general introduction to bridges, what bridges mean. And it will be mostly a recap of what you have already learned in your earlier session. But also, we'll be trying to put some additional inputs, how it is relevant, what difference does a steel gutter bridge make. In this session, we'll be learning about general introduction to bridges and what are the various components of the bridge. Then also the third one is what are the type of bridges that are generally used.

So the first one will be learning objective. In this session, we'll be learning about basics on bridges, how the load is transferred from each of its components, and how bridges are classified according to materials, then purpose, then behavior, and also span. Bridges are built to connect two locations over an obstacle such as rivers, valleys, oceans, roads, or railway traffic in general. The obstacles could also be anything. What they connect could also be the same in quite a few cases, except valleys, of course. You cannot transport a valley, so a rest of the things.

For instance, the bridge that transports a river or a canal is called an aqueduct. And the same can apply to ocean in certain cases. And also in the next case, you can see a road bridge or a railway bridge is pretty common. But in quite a few cases, the bridges are made to cross them as an obstacle. And these are called interchanges in general. Bridge engineering is generally a part of structural engineering. And it is not a single-standing engineering. You can say a bridge needs various parts of engineering.

For instance, the basic part is structural engineering, even though. But at the end of the day, it's also transport engineering or traffic engineering, because we are transporting vehicle over in most. And in certain cases, it could be also irrigation engineering. For instance, it could be for a canal. Generally, bridges generally help in community or economic development. You can see it in most cases where there is an economic downfall, then the government generally induces the money in building of the infrastructure, that is the roads. And it also includes bridges.

Then it also, in most cases, for instance, if there are two locations that need to be connected, and there is an obstacle flowing in between. For instance, it could be a valley, which is separated by two mountains, which are separated by a valley. In that case, you could see that in most cases, people have to get down all the way from one mountain and get up on the other one. This could lead to a lot of carbon dioxide emissions and also greenhouse gas emission due to the vehicle.

But connecting them with a bridge can reduce the effect, even though it incorporates some of the carbon dioxide emission in the initial state. But in long term, we can prevent it because of the vehicle. And it also helps you with the commuting. So in certain cases, you can see that if there is no interchange inside a city, it would increase your commuting time exponentially. So this separates people. So if you don't provide bridges or an interchange, this would increase the traffic time and it would actually affect the lives of people because you cannot be reaching places in time.

So that's why a bridge also helps you in economically this way as to again general friction. The oldest type of bridges you could have seen are mostly basically beam or flexure bridges. So this could be seen even in current scenario. If you have a small canal or a small drainage, what generally people tend to do is put out if you have a locally available stone, you can just shape it and put it over there so that your vehicle or yourself can pass through that obstacle or a canal or a drain.

And so as I have explained, there are stone or timber logs laid as slabs to cross smaller waterways, which can be traced back to prehistoric times. People have been doing it a long time. It can be even evident in some other cases like animals also do the same in case if there is a wooden log that has fallen across a small waterway, then animals use that to cross. Other older type of bridges which designed a plan are masonry arch bridges from Roman era. And also we can see rope bridges in rural areas of Asia or South American civilization where materials like rope are naturally available.

For instance, in India, you can see rope bridges, as they say. And in other civilizations as well, they have been using grass to create ropes and the same can be used for creating a bridge over a long time. While arch bridge can be used for shorter span. Bridges are not only used for transporting other things, but as I mentioned earlier, they are very effective in transporting water as well. Aqueducts have been dated back to 300 BC. That is like 2300 years before now. They have been used since then.

When cities need water, a river is diverted and the water can be transported through a canal. And the canal is in turn taken by a bridge which is transported from one location to the other. In certain cases, there are two bridges passing through. When you want to take water from a higher source without falling into a lower source path, it would affect the flow of water. That means if you have a city on another hill while your water source is on another hill and there's a valley down, you cannot bring it to the other hill directly.

So in that case, you need a bridge that can take it without the water flowing into the valley. So with the current advances, so this has been dated up to, we can say, 500 years back. But in current date, we can see there are quite a lot of other bridges as well. We can see cast iron bridges. It started with cast iron bridges, then reinforced concrete bridge, then steel bridges. And one of the newest is priestless concrete bridges. Even though we call it newest technology, it has been there for more than 100 years now.

So generally, you can date cast iron bridges up to 200 to 300 years from now in early Britain, where you can see bridges made by Tom Stelford. And the same developed into steel bridges when, in most of Europe and also in the U.S., they wanted to make steel cables to make bridges and even steel jack in certain cases. And reinforced concrete has also been used since a long time. And one of the newest is priestless concrete technology. This has been developed by Fresenet and a French engineer, as I know.

And this has been developed. This has been in use. It's now almost 100 years since he has been using it. This behaves somewhat very similar to the arch, which has been widely used in those times. So these are the general types, as I've mentioned. So you can see to the left is a Roman aqueduct. And to the center is a road bridge or a root bridge. And to the right, you can see the millennium bridge and landmark. So which is a landmark in our current scenario.

So next, we'll be seeing about various components of the bridge. The components of the bridge is basically classified into two. So one is a superstructure and the next is a superstructure. In general, it is classified as any component that lies above the bearing is called a superstructure. And any component that lies below the bearing is called a superstructure. So anything above the bearing could be deck slap, then main girders, cross beams, cross bracing and steel bridges. Even though they almost perform the same work, a cross beam is a beam that is provided between two main girders in a concrete bridge or also in a steel bridge in case of it is provided as a beam.

Cross bracing is when it comes to a steel bridge. They might not be exactly beams. In certain cases, there could be trusses as well. So they prevent the differential deflection in longitudinal girders. So if one girder is going to deflect more and the other girder is not going to deflect, the deck might be damaged. So for this purpose, mainly cross beams are provided or cross bracing is provided in this case. And they also help in transferring the wind forces. We also use cables. This is also an element of the superstructure.

Then we have edge beams, curbs, expansion joint, regular restraint system. They're all superstructure components. Any component that lies below the bearing such as approach slab, wing walls, return walls, back walls, abutment walls, foundations, pier, pile cap, pile cap, etc. are used as substructure. This also includes caissons and other types of foundations that are generally used in India. That foundations in general even in building means substructure. So here also it means substructure. So here in the image you can see that. So this is the approach slab.

So approach slab is generally provided with a bit of sand above it or the road above it. And this is provided so that if the vehicle passes through over and over the sand or the road, they can settle. So over the period of time when this settles, the soil over here settles, the vehicle is not capable of getting into the highway. There could be a block or there'll be definitely a differential height between the roadway here and also the roadway on the bridge. So that's why we provide approach slab so that there won't be any sharp obstacle while climbing the bridge.

And this is the abutment wall. So you can see this entire component is called the abutment. So the front wall is the abutment wall. This prevents the sand from behind the bridge that is on the abutment wall. Approach area to fall into the open area, that is a valley or whatever which we are crossing through. This is the back wall. So this also does the same retaining work, but instead of only the front area, it also prevents the soil from falling sideways. And so the back wall is over here at the top. That is, it doesn't allow the soil to pass through the front.

The back wall is the wall that is provided above the abitment wall. So it is, it starts from the level of the bearing where the bridge is placed and, and it extends up to the highway or just below the approach slab in most cases. So this is also effectively a retaining wall that prevents the soil from falling front walls. So the, so that the soil doesn't come in directly contact with the girder. The girder might be even though deep, up to two meters or one, whatever the depth it is, there'll be an area where the, there'll be hollow space between the girder, as you can see over here.

If we don't cover the area over here, where the sand is falling off, the sand could be falling inwards into the span area. So that's why we provide a back wall in this region to cover, to cover the soil from falling inwards. Next is the wing wall. So the wing wall is also again a retaining wall that is provided just to prevent the soil from falling sideways. So this falls into the span, while this falls sideways. If the soil moves effectively, it could affect your highway, which is lying behind.

So if the soil flows from this area into the span area, effectively it will reduce your height and effectively it can prevent your traffic on the bridge because the vehicles cannot climb into the bridge due to settlement or due to damage. So that's it about the abitment. And next we are coming to the substructure, that is the piers. So here you can see, these are the bearings. The bearings can be either elastomeric bearings, port bearings. In olden days, roller bearings used to be used. Nowadays, they are not being used.

While elastomeric bearings or port bearings are used, they are much more superior and requires lesser maintenance compared to that of a roller bearing. Here you can see this is a pier element. This could be of various shapes. They can be a circular column like elements with a frame or they can be wall type piers. And also there are quite a lot of other types of piers, which you could have seen in substructure design. And then we have the pile cap over here. So in general, where the piles are provided, a set of piles of almost 30 or 40 piles are provided.

In that case, we need a pile cap that rests on all the piles and over that rests the piers. So that's how the force is being transferred from superstructure, that is the deck slab, to the girders and then to the bearings and then to the piers or to the abitment, then to the pi cap and piles and then eventually into the soil. Or in case, if they are still directly on the rocks, to the rock. And here we can see this is a sample of a deep foundation, while this is a sample of a shallow foundation, that is a footing.

And here we can see deck slabs. Deck slab also, there are quite a few types. For instance, there is jack arch slabs that are provided. So instead of providing a slab over here, in olden times, they used to provide an arch over here, which is a brick arch. So brick arch, it's a smaller arch that spans up to one or two meters, which is the spacing between the girders. And the force used to be transferred in the form of an arch instead of in the form of a.

So that is one of the types of deck slab. In other types, we can see pre-stressing elements or post-tensioned elements. They can also be used. In certain elements, wooden deck slabs have also been used in the past. And in railway bridges, for instance, there might not be a deck slab at all. You might have a track that is directly resting over your main girders. Or in the trusses, in cases like trusses, you have a rafter. So that carries your track. So the track transfers your forces into a girder, which eventually transfers your forces into the cross beams.

And they transfer your forces to them. So that's how it works in a railway bridge over in a truss, where the deck slab is not necessarily required. And here you can see in the elevation railings or vehicle restraint systems are always provided over the bridge. We can come to curbs. Curbs are also somewhat, instead of vehicle restraint system, it is a shorter way to prevent the vehicle from falling off. It reduces your speed when it comes inside by accidents. It also acts as a place where the footpath can be placed.

Then here you can see, this is the surfacing or the wearing coat, we call it. Wearing coat is one of the most maintained one. So throughout the life of the bridge, this can be replaced. So this generally has a higher factor in dead loads. Generally, dead loads have a lower factor of aviation, like the main girders, which is a structural element. They generally do not tend to change in their lifetime. Only when there is a repair or a modification, then only the weight tend to increase or decrease.

It generally doesn't decrease, but increase. But a wearing coat, it is generally scrapped off. When the highway is being maintained or relayed, in certain cases, they can add some more to the highway. For instance, this could be 110 millimeters. And when they are putting the next layer of highway, they would add some 50 millimeters over this wearing coat, just to make it smooth. So maintaining the wearing coat is also very important for the bridges, because if you have a lot of potholes and things in the bridges, and if they are subjected to a high number of vehicle flows, this could add your dynamic addition.

That is, that will eventually increase your vertical load that can damage your bridge through fatigue. That is, the repetition of vertical load in a higher factor than it is expected on the bridge. Or even in the ultimate limit state, not generally in the ultimate limit state, but in serviceability, where you will be designing the girder for a particular, but due to the higher wear and tear of the wearing coat, there could be higher loading that can act on the girder. So maintaining a surfacing is also a pretty much important job.

So again, as we have discussed, this is the next lab, which is shown in the cross section. So this typically looks of a reinforced concrete section. In the next one, we can see how the same applies for a steel section. This is from actual project. So here you can see a two-span bridge. This is a steel eye girder with varying sections. So here you can see the cross section of the eye beam over here. And this is what is called a cross frame or cross brazing.

So this generally helps in prevention of a differential deflection of the girders. And here you can see that there's the deck and the wearing coat over here. There's the vehicle restraint system. And this is the abutment. And this is the, sorry, this is the abutment, while this is the pier. So this bridge has a very weird kind of shape of pier, since this was a very old bridge that was built in 1960s, around 1960s. So this is designed in such a way that the water flow and the center of gravity lies in such a way that they don't have to put a higher motor.

That's why one side is increased, while the other side is generally small. This kind of optimization was very preferred in old days, but in current scenarios, it is not much preferred, this kind of ones. While an easier construction is always preferred. So they generally perform a vertical wall type pier in case of water. Or if it is not in water and if it's an interchange, for instance, they generally prefer a smaller occupation of area. In that case, they provide a frame kind of arrangement, where two circular piers will be acting over here and there'll be a beam over the top.

So here, this also shows actually longitudinal stiffness over here. So these lines, horizontal which you are seeing, are the longitudinal stiffness. That can be seen over here as well. The longitudinal stiffness are generally provided in the compression zone. So that's why you can see in the main span, the bending happens downwards, but the top flange is in compression. You can see the longitudinal stiffness closer to the top flange. While in the support, generally a hogging moment happens. In this case, the bottom flange gets compression. So, again, the longitudinal stiffness has just changed and are provided closer to that of the bottom flange.

And here you can also see that the vertical stiffness, this is an eye beam, but you can see it like a rectangle. The reason being that these are the transverse stiffness. So you can see the location of transverse stiffness over here, here, and also here, similarly over here. So these are also the location of the cross-trains. So cross-trains are provided where the longitudinal stiffness are provided over here. Sorry, transverse stiffness are provided over here. Okay, and coming to the components and what are its purposes. Components and purpose.

First is the superstructure. Deck slab is generally the element that directly takes the vehicle or live load from the bridge across the width. It is generally made of reinforced concrete. As I have mentioned earlier, they can also be brick jack arch in earlier times. If you are going for an assessment, they can also be easily formed in quite a few olden bricks. Then coming to girders. Girders are the members where the loads are transferred from the deck. They can be made of steel, concrete, masonry, and can be in the form of truss, arch, girder, or in other forms as well, like in cable-stay bridges or in suspension cable bridges as well.

They distribute the forces to the substructure. Cross-beams and drizzings are used to distribute the deflections between the main beams so that the deck does not fail due to the relative deflection between various main girders. In addition, they also provide restraint against wind and other lateral loading in long-spun bridges. Edge beams are replaceable components which are designed to hold the vehicle restraint systems and can be replaced in case of a crash. In most modeling of the bridges, it is preferred not to model the edge beams because if you model the edge beams, they can add stiffness to your deck.

And in case of a serviceability condition where the edge beam is removed and the vehicle passes closer to the edge beam, of the deck, it can fail in ULS. So for that, so to prevent that from happening, we generally prefer that the edge beams are not modeled in natural design. The moments that are occurring from the edge beam, that is due to the impact of vehicle on the vehicle restraint system or impact of the pedestrians over the handrails or wind loads, these kind of things need to be transferred from the edge beam to the mean deck slab. So these moments are transferred, but the stiffness of the edge beam is generally not preferred while modeling the bridge.

Vehicle restraint systems are provided so that the vehicle does not fall off from the bridge in case of negligent driving. But in case of providing them in such a stiff way, it can also cause death of passengers because of the vehicle crashing so hard. So they are mostly preferred in such a way that they take the energy from the vehicle, but they are not that stiff that it causes severe damage to the vehicle. So in case of a truss bridge or bridges through type bridge or semi through type bridge, the vehicle generally passes between the girders or the load bearing elements of the bridge.

So in that case, actually, we prefer to provide a stronger vehicle restraint system that protects the structure. But these kind of crashes could be catastrophic, as you know, because in case of an accident happening in a crowded truss bridge, you could damage the trusses in such a way that the bridge entirely collapses. There could be like 30 or 40 vehicles on the bridge and the entire thing can collapse. So that's why the design of a vehicle restraint system is also pretty important in case of bridges like this.

And the next one is the expansion joints. Expansion joints are generally provided to allow movement of superstructure in case of thermal loads, which is restricted, may cause huge forces in the substructure. So you might have already learned about the bearing articulation. So if you do not provide free bearings, that is the longitudinally free bearings, to allow the bridges to expand or contract. So in that case, what happens is when the bridge is prevented from expanding, the superstructure is prevented from expanding, they can induce too much of presence into the substructure.

So that's why we provide expansion joints. But in this area where the slab terminates in the expansion joints, there needs to be provided additional stiffness, because it's a sharp edge where the vehicle passes through, and it needs some stiffness to resist it from bending. Because the loads happening at the edge of support can be somewhat higher, and it could be very concentrated. This causes cracking of the deck slab in the edges. So expansion joints are designed in such a way some steel parts are provided. It behaves like a steel beam is provided at the end of the slab, so that the load of the vehicle does not deflect or crack the deck slab.

Coming to substructure, vehicles take the load from superstructure, like girders, trusses, arches, and also they transfer it to the substructure. Effectively means some people take the bearings in the superstructure, while some assume that it's a substructure. So I assume it is a component of the substructure. So in most cases, the girder transfer the loads from the deck to the bearings, and the bearings take them and transfer it to the substructure, that is the peers. Provided to allow rotation and movement in the superstructure without damaging the substructure, as I have mentioned earlier.

So movement is used for this term of the thermal expansion, while rotation is also pretty important in a bridge. So if a girder is directly placed on the pier, they cannot rotate effectively, because you have a particular length of the girder at the bottom of the girder that is acting somewhat straight. We already know, you could have already learned in your design of analysis subjects or in design subjects, where rigid support is a rigid end of a beam. It's a beam where the angle of rotation is 90 degrees.

We assume that the support rotates entirely by 90 degrees, and there is no relative deflection. So that is a rigid support. So in this case, if you're providing, if you're directly resting a girder over a pier, so until the length of the pier, where the pier ends, the bridge cannot effectively rotate. In that case, the bridge can either damage the substructure and crack it, so that it is able to rotate and come to its natural state. In certain cases, the girder itself is damaged due to a hogging moment that is caused.

So if you don't provide a proper bearing, there could be hogging moments induced in the simply supported edges, and they can damage your structure. So that's why rotation is pretty important. And to enable that, we are providing bearings, especially roller supports or pot bearings or elastometric bearings that can allow rotation. Pier heads are provided in cases where the size of the pier is not capable of carrying the concentrated load from the superstructure. They also help in cases of multiple bearings resting on a support, like two simply supported beams on a support.

Then pier transfers the load from superstructure to the soil. They can be wall-type or concrete slash steel frames as well. So pier, as you know, they can be either wall-type pier. In that case, you can directly rest your superstructure or rest your bearings on your wall-type pier, where there is enough space. But in certain cases, we also know that there is not enough space to place two bearings. So in that case, you need to provide a structure that is somewhat bigger than the size of the wall-type pier, so that you can rest both your bearings over there.

And similarly, if there is a frame type of arrangement, the top of the frame, which is a beam acting at the top, it's generally called the pier cap. So, which transfers the load from the bearing to that of the frame length. For instance, in most bridges, you can see that there are two simply supported girders. You can see that both the girders end over in a single pier. So, in that case, what they do is to accommodate both the bearings. They generally provide an extended pier cap over the wall-type pier.

While in case of a continuous girder passing over, they provide a single bearing that can transfer the load from the girder to the substrate. In case of a frame-type bearing arrangement, here you can see that there are two legs while there is a top pier cap. So, this is required to transfer the mid-bearing force to both the bearings and also at the ends. Abortments are pierced provided at the interface between soil and the bridge. In addition to taking load from the superstructure, they also retain earth.

In certain cases, like reinforced earth abutment walls, they retain soil but do not carry superstructure. Instead, they are carried by pierced provided adjacent to wing walls. Wing walls and return walls are provided to retain soil on sides of the embankment, provided at the elevation of the bridge. Back wall is mostly the extension of the abutment to retain the soil at girder or deck level, as we have discussed earlier with the image. As I have discussed earlier, approach slab is provided to distribute the wheel loads to the soil at the approach of the building and prevent it from settling and making it impossible for the vehicles to reach them.

Coming to foundations, foundations can be in various forms, such as piles, caixons as in case of deep soil and huge loads. For simple footing, in case of soil is strong and enough to carry loads at shallow distances in the ground. Next, we are going to see the type of bridges. So, there are also various classification of how the type of bridges is classified. The first one is with the material. So, most of the bridges are of reinforced concrete, and certain elements could be of, certain bridges are of steel.

Then, also you can see pre-stress concrete bridges and also fiber reinforced polymer, which is a trend nowadays. Quite a few bridges are coming up with fiber reinforced polymer. Coming to the type of bridges based on the basis of purpose, we can see basic types of bridges. For bridges are the bridges which pedestrians use to cross a highway or in case of a waterway canal, etc. And also even a railway. Then, coming to the second type is the railway bridge. The railway bridge is used to, as you know, what passes over the bridge is what it has been mentioned over here.

You can see that a railway bridge carries the railway loads. Then, you can see a road bridge and an aqueduct. Aqueduct is a kind of bridge which carries water, especially a canal, over your normal traffic or even a valley. So, behavior is one of the main type of classification. Bridges could be classified into compression bridges, then fracture bridges, and also tension. So, first one is if you go into compression bridges that transfer load through compression, that is basically an arch. So, if you look into buildings, there are quite a lot of other compression elements such as walls, domes, etc.

And quite a lot of other shell shapes which can completely transfer load through compression, through a masonry. But in bridges, generally, the type of compression bridges are arches. Some elements of the trusses, they also transfer forces to compression. Like, for instance, if it's a simply supported truss, the top cord in the mid-span generally transfers compression. Coming to flexure, as you might know, flexure is the phenomenon which takes bending and shear into effect. So, generally, slab bridges behave this way, beam or girder bridges behave this way, and even cantilever bridges.

And the next one is through tension. So, simply, the pure form of tension-carrying bridges are cable-stayed bridges. The main load is directly transferred through the, sorry, not cable-stayed bridges. The main type of bridge would be suspension cable bridges, which directly take the loads through tension in the suspender or the main cables. And the next type is also cable-stayed bridges. They have... Radial cables connecting the pylons with that of the deck. So in this type of bridges, generally it's in tension between, the cables are in tension between.

The next one is the truss bridge, again in tension, because truss directly transfers forces through either compression or tension. This is effectively flexure, but it is truss. So it directly takes either tension or only compression in a particular element.

Want the rest of Design of Steel Superstructure in Bridges?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Design of Steel Superstructure in Bridges course

The remaining 41 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Design of Steel Superstructure in Bridges course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.