← Previous lessonFree lesson 2 of 3 · lesson 2 of 55Next lesson →

Unlock all 55 lessons of Design Concepts of Power Electronic Converters for IndustriesFull course ₹40,000 · paid

Price & syllabus
Free lesson · 19 min · no payment

Converter Control and Applications: Boost Converters, EVs, Solar and Chargers

A free lesson from Skill-Lync's Design Concepts of Power Electronic Converters for Industries course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”

What will you learn in this free Design Concepts of Power Electronic Converters for Industries lesson?

Continues the introduction with feedback control of converter switches using MOSFETs and IGBTs. Then covers boost converters and walks through applications including the Tesla Model S drive and charger, photovoltaic systems and a cell phone charger.

  • Feedback controller with reference, switches and DSPs
  • Boost converter stepping a battery voltage up
  • Tesla Model S inverter, charging and power factor
  • PV systems and cell phone charger stages

What comes after lesson 2?

The next free lesson is lesson 3, “Converter Efficiency, Buck Converter Duty Cycle and Ripple Sizing” (46 min). Later in Skill-Lync's Design Concepts of Power Electronic Converters for Industries course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 55 lessons (24 h 51 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hi, everyone. Again, continuing upon the introduction to power electronics here, we were looking at a power converter and power input and power output that's available onto the power converter. And then how we adopt a typical controller, which is designed such that we receive the feedback at the power output, where the controller is looking at a reference, which it could be a current or a voltage command or torque command, which is coming in here. And then we get the feedback. And it's also looking at the input side, if there is a DC voltage that's coming out, so DC voltage, and then to be able to generate output, which is controlling the switches or MOSFETs or IGBTs within here to generate the power.

So, this is basically typical analog feedback. There is sophisticated controls that's used by using the digital microcontrollers and DSPs and FPGAs, which is the main, again, the block of the power electronics, which is used in the industries. Okay. Let's continue on to the introduction again. We will see the typical DC-DC converters that we talked about earlier. There are the major categories like the boost converter, which is looking to generate a voltage, which is higher than the input voltage. So, it's like a step-up converter, where in certain cases, for example, you're using a battery, which can only provide 200 volts, and for your inverter used on the vehicle, which needs 700 volts input, and that's where the boost converter is coming into the play to generate a higher voltage from a lower voltage.

And certainly, the power on the output would be limited because the increase in voltage would be compensated by decrease in current. So, that's a typical application here, and again, it's being used on several sort of applications to step up or increase your voltages on different charger applications using power factor corrections and other different topologies. We will not dive a lot into the DC-DC converters, as I said, because it's being demonstrated on a different course within the skill link. Then, we've got buck converter. It's doing kind of exactly opposite.

It's stepping down the voltage from high voltage into a lower voltage category to provide increased current output, so you can drive loads which are rated for lower voltage but higher current. Or, there is a buck boost converter where you can do both, so step up or step down depending upon the application, and you can also build the converter such a way that it's also bidirectional as well. Then, the flyback converter, all of these three topologies on the top that we talked about, they are non-isolated converters.

You could build a converter which is isolated by using the flyback converter which has a transformer that's basically isolating your input and output, and that's used again extensively on some of the applications too, where isolation is required between input and output and grounding is not common. Then, the DC-AC or AC-DC converters, these are basically bidirectional inverters where you can do both rectification and also conversion, and the next one is AC-AC converters or cyclo-converters where the application is to be able to generate the same AC waveform maybe with a varying voltage magnitude or with a variable frequency.

The power electronics is a very diverse field, so we will see around power electronics, there are different blocks that build it up, so maybe let's dive from over here, so power systems uses the power electronics, the electric machines, they use power electronics, simulation and computing is used by power electronics, and so these, all of these different fields in here, they use it. So, to be able to work on your power electronics design for a certain application, you would also need to know about the application as well.

The solid state physics is used in power electronics where we are basically using certain switches, MOSFETs or IGBTs or silicon carbide materials or gallium nitride. Circuit theory is kind of the most important one here, so you need to know how different circuits work to design your power electronics system. how the controls are designed and how do we control it in a higher system level and establish all of that communication and other things. Signal processing is also another one when we receive a certain voltage current and feedbacks there is also a processing that needs to be done, implementation of filters and the discrete filters onto the microcontroller as well.

Electronics is again that's all the low voltage electronics that builds and make the power electronic system to work and electromagnetics involves using transformers and inductors and other electromagnetic components which make up the power electronics. So these are all kind of the variety of areas where there is prerequisite that you would know this to design your power electronic converter when you have a project to work upon. There are certain things again we are looking at here and how power electronics system can be designed considering the power cost volume and some limitations and failure rate into the picture. So if you try to cover the full map over here that would result into a system which is amazing the power loss is lower the cost is also lower the volume and weight would be lower the limitations are probably very low the failure rate is also low. But to design such a system it's also not feasible to design such thing which can do all this with a very minimum cost. So again let's not look into something that's not practical certainly there are certain trade-offs that needs to be done that's where the green and the blue lines come into the play where when you're designing a system you want to target on certain areas. So if cost is important factor you try to look for the cost and then see how to compromise your power losses maybe you can allow some more power loss you can probably allow some failure as well and you can allow some limitations and then your weight and volume are probably better so your cost and weight and volume are basically driving the decision. Or maybe there is another design where you're looking into power loss and failure rate mainly so these are minimum while you do not worry too much about the cost and the weight and the packaging. So these are the trade-offs that needs to be done in your architecture before you start designing a power electronics system and these typically apply to sort of any project as well. So that's all on the introduction to power electronics next we will dive into the applications of power electronics. So this is the interesting part to see how these are applied and we'll go through the examples that I mentioned in the beginning. One of the examples here is the electric vehicle again taking Tesla. Tesla is in the market and it's one of the hot names for electric vehicles and almost everyone probably knows about Tesla. The function of power electronics here in Tesla is basically converting the DC voltage to an AC voltage which can drive an AC motor.

Most of the Tesla cars were using the induction machines. I think they are switching to permanent magnet motors now. So it's a 240 volt battery that's basically driving the machine which is a variable frequency variable voltage AC drive motor and this is where the power inverter come into play which is controlling the voltage and frequency to drive the machine. There is about 330 kilowatts that you can achieve during acceleration and about 60 kilowatts of regenerative braking. So that's kind of the specs of Tesla Model S and typically it is interfaced to a 240 volt 100 amp 60 hertz charger in the garage so someone can put this and plug it into your garage and be able to charge your vehicle overnight. The power factor is also controlled so there is unity power factor which is controlling the AC current waveform so that it's sinusoidal that's the typical thing when we are trying to convert and rectify the waveform the power factor is lost so it's not sinusoidal it's again there is some sort of lag that's introduced and also controlling the charging of the battery to maximize the life. There are some pictures over here that I showed so looking at the dashboard and in Tesla Model S you would know what's the mileage that's available the mileage here really refers to the state of charge of the battery and then see how much you can drive and also state of health and it also the interface here on Tesla Model S shows you certain GPS interfaces and then how to drive your vehicle. There's also autonomous driving that you can do so you can pre-program the address and then the car will drive you there. So those are again kind of the future applications and then how to use and self-driving sort of atmosphere which is still in progress and developing so there's a lot of room there to grow. The next application here we'll look into a variable speed wind turbine so a wild AC is produced by an AC generator so when we look into a wind turbine it's spinning such that based upon the wind so there is going to be some sort of AC waveform generated it's not consistent right because the amplitude of the waveform is going to be proportional to the velocity of the wind so a wild AC is And the utility here, it basically operates with a constant voltage and frequency. So we know that that's what the utility or this is the grid that I'm talking about. And with the help of the power tectonics, you can change the frequency and the voltage. So implementing a cyclo-converter or using a rectifier or inverter or DC-DC converter with those implementations will be able to control and then make the AC output in a form that can be used reliably.

So let's look into a schematic. The variable speed winter wind is using basically a rotor here. These has the rotor blades and then these are spinning based upon the wind velocity. So there is going to be a certain speed which is generating a certain sort of torque, you can say. And then the gearbox here and this is converting that lower speed into high speed which is driving a generator here. So generator converts this mechanical energy into an electrical energy. The energy generated from here is again not uniform because it varies depending upon this rotor and then how wind plays into it.

So that's where we're going to go. So that's where we're going. So that's where we're taking the currents as a feedback and using a power electronic device to excite the generator into different feedback. So we can generate a constant voltage or current output here so that you can feed that into your utility or grid and then generate some revenue out of it. So that's what major wind farms do. So that's what major wind farms do. They have a lot of different wind mills and then they are basically combining every mill to generate a certain power and then converting the power in using power electronics into a farm that's uniform where the voltage and the frequency and current are called controlled that you can push into the grid and are you use for your own individual application.

The next application here is using in a PV sort of atmospheres of photovoltaic cell. There are different applications of photovoltaics where they are expanding a lot into certain areas where there is not much availability of the grid power or the electricity is expensive. And also with renewable energy focused upon by different regulations and government. So the solar cells have been also one of the prime paths for microgrids sort of atmosphere. So there is a grid tied solar or a standalone solar that's typically being used. The grid tied solar here, an inverter here converts the DC power of the solar panel into the AC and then feeds it into the grid.

For a standalone solar, it basically generates a DC, then there is a DC-DC converter that's used which is charging the batteries and then you can use the batteries right into driving the loads that you want or again using an inverter to be able to drive an AC load or even sell that electricity to generate some revenue. So these two are again different sort of applications, but nonetheless, again, solar cells, as you would see here, this is a solar farm and it's basically the solar rays here, they fall at an angle.

There is typically an angle of 30 to 45 degrees that's kept here for maximum penetration. So you can generate the most sort of energy that's available during the day and then be able to store that energy and then use that into the peak hours. So that's how people are generating different revenues by selling them during the peak hours and also combining the solar with your other microgrid systems by using some storage by batteries or some hydrogen fuel cell stack. You'll be able to combine and using this power for about 24 hours using generators and other things.

So looking a little bit again deeper into the PV system here. So let's consider the PV input here that's generated from the solar is about 12 to 100 volts. And then this really depends upon how many stacks of solar that you got and how you are putting them and then how you are paralleling and providing that input. So there is a voltage which is going to change also depending upon the penetration rate from the sun. So you generate a certain input here and using the buck boost converter, we are able to boost this particular voltage or even reduce this voltage for higher current.

So from 12 to 100 volts, we are generating a steady 48 volts. So again, remember the voltage that's coming into the PV is variable because it's varying depending on sun intensity and conversion and then day timing. So we want to make it into a reliable and fixed steady state output. And that's where this buck boost converter will regulate and control it to a 48 volts. And then using a DC transformer here with 1.28, so we are basically stepping up this into a 400 volt. So again, a variable input is converted into a high voltage output here that can be fed into the inverter.

And from inverter, you can generate the AC waveforms that can drive any sort of loads. So that's the typical sort of architecture that's used for the PV. And certainly at the bottom, we have got the controls to be able to do either the buck boost conversion or using some sort of power electronics and gate drive circuits and transformer here. So you would need a controller with different feedbacks on this side, feedbacks here and input feedbacks to generate your particular output. So there's definitely a lot of scope within PV system and power electronics that's growing for the future as well within different areas of the country.

Next one is an application, which probably all of you are familiar with. Almost everyone now uses a cell phone and cell phone chargers, they also use power electronics. So we are using this almost a day to day, the chargers, and then we'll see how power electronics actually plays a role here. When you plug in into your charger into an AC input, there is a variable AC input that's available. It could be 110 volts AC or again, it could be a three-phase input that's available, but again, and then convert the chargers for a single phase.

So there is a single phase AC that's available and we plug in our charger. The charger has a rectifier, which is converting that AC into DC, and that DC is basically charging a lithium battery. And the rectifier here is also making sure that it can do rectification along with some filtering. So our output here is not pulsating sort of DC. You can make sure there is a constant flat DC. And then we use that DC to make a small inverter, which is basically generating some AC output, which is powering up your display.

So there is a small inverter that's used to do it. Then we also convert that into a very low sort of power supply. So this could be a power supply, say the batteries can work up to say 20 volts. So the microprocessors are typically either 2.5, 3 volts rated. So we convert that into a very low power range that can drive and control your microprocessor and different sort of circuits on to the cell phone, a PCB. And there is also a boost converter here, which helps with the disk drive.

So there is storage disks and other things. So it's also looking to provide power to that. So there is a complex sort of charging interface that a phone has built. And it is also used in different computer servers and server farms where the application or architecture is pretty similar. So you can see on the right side, I have just pulled up an iPhone power system and charger where you can look again to the charger has everything built in within this just a small package. So again, none of this is very high current rated, right?

We are looking at 2.5 or 3 amps to the max to charge the battery. So this is very low current system and you can play with the packaging to make it really compact and also cheap. And that's where the innovation falls in, right? Okay, great. So, yeah, thanks for watching this particular module or session. Pause here and then we'll continue for power electronics design next. Thank you.

Want the rest of Design Concepts of Power Electronic Converters for Industries?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Design Concepts of Power Electronic Converters for Industries course

The remaining 52 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Design Concepts of Power Electronic Converters for Industries course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.