Lesson finished
Unlock all 29 lessons of Civil Engineering Fundamentals ModuleFull course ₹40,000 · paid
Aggregates: Properties and Laboratory Tests for Concrete
A free lesson from Skill-Lync's Civil Engineering Fundamentals Module course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Construction Technology”
What will you learn in this free Civil Engineering Fundamentals Module lesson?
The instructor classifies fine and coarse aggregates at the 4.75 mm sieve and explains the tests on aggregate: crushing, Los Angeles abrasion, impact, soundness, flakiness and elongation index, specific gravity with water absorption, and bitumen stripping. Procedures and limits are given, such as crushing value as W2 divided by W1 times 100.
- Fine versus coarse aggregate size limit
- Crushing and abrasion test procedures
- Impact and soundness test limits
- Specific gravity and water absorption calculation
What comes after lesson 3?
Later in Skill-Lync's Civil Engineering Fundamentals Module course (paid): lesson 4, Introduction to Cement and Admixtures in Construction Technology; lesson 5, Types of Special Cements and Their Uses in Construction; lesson 6, Introduction to Construction Technology. The full course has 29 lessons (10 h 57 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello and welcome everyone to this online course on introduction to construction technology. In our last session we saw about the basic building materials used for construction. We saw about the construction materials sand, bricks, concrete blocks, arachon blocks, hollow clay bricks, hollow concrete blocks, fly ash bricks, glass, temper or wood, reinforcement bars and structural steel. In this session we will be seeing about aggregates and cement in detail. We will be seeing about their properties, their tests and the types of aggregates and cement. Aggregates. Aggregates are the most widely used products during construction. Aggregates are granular materials used as one of the ingredients to make up the proportion of concrete.
These materials include gravel, sand, crushed stone etc. obtained from crushing of rocks. Aggregates are classified into two types based on their sizes as fine aggregates and coarse aggregates. Let's see about fine aggregates. If the aggregates pass through 4.75 mm ISC then this type of aggregates falls into the category of fine aggregates. Example for fine aggregates are natural sand, crushed gravel sand and crushed stone sand. Coase aggregates. If the size of the aggregate is bigger than 4.75 mm then it is considered as coarse aggregate. Example of coarse aggregates are uncrushed gravel stone.
Common size of aggregates used in concrete mixes 20 mm for coarse aggregates and 4.75 mm for fine aggregates. The total volume of concrete normally consists of 75% to 85% volume of aggregates that makes the cost of concrete relatively low. So aggregates act as structural filler in the concrete. Hence it is very vital to consider the qualities as well as properties and gradation of aggregates before carrying out concrete mix design. Before choosing the aggregate it is very important to know about its properties to get the better quality of concrete.
Aggregates should be tested for its suitability, strength, toughness, hardness, shape and water absorption. The standard guideline for the test on aggregate is followed as per the CODEL specification. Indian Standard Code 2386 Part 4 1963 Methods of Test for Aggregate for Concrete and British Standard Code BS 812-110-1990 Testing Aggregates Methods for Determination of Aggregate Crushing Value is used as a guideline for the test on aggregate. Properties of Aggregate Basic properties of aggregates mainly depend upon the physical properties and properties of the parent rock. These properties will have an impact on shrinkage, workability, strength and durability of the material.
Aggregates are tested for its suitability, strength, toughness, hardness, shape and water absorption. Properties of aggregates are strength, hardness, toughness, durability, shape, alkaline aggregate reaction, specific gravity and addition. Now let's see about the tests carried out on aggregate. Crushing test on aggregate, abrasion test on aggregate, impact test on aggregate, soundness test on aggregate, flunkiness index test on aggregate, specific gravity and water absorption test on aggregate, butumen addition test on aggregate. The crushing test on aggregate is used to determine the strength of aggregate. Abrasion test on aggregate is done to measure the wear and tear of the aggregate.
Impact test on aggregate is done to find the toughness of the aggregate. Soundness test on aggregate is done to study the resistance of aggregate to weathering action. Flankiness index test on aggregate is done to determine the shape of the aggregate. First let us see in detail about the crushing test on aggregate. The crushing value of aggregates indicates the strength of aggregate which is the most essential property of coarse aggregate. The crushing value provides a relative measure of resistance to crushing under a gradually upright compressive load.
High quality of material is achieved with aggregate of higher crushing strength that is with low crushing value. Lower crushing value means higher strength as it indicates a lower crushed fraction under load. This gives a longer service life and more economical performance. After performing the test the crushed material is separated and calculated in terms of percentage of the original weight taken in the mold. This percentage is known as the crushing value of the aggregate. This percentage should not exceed 30% of the total weight of aggregate taken for the test.
The aggregate crushing value test results should not be more than 30% for the concrete which is used for the construction of roads and pavements. And in case of other structures it may be permitted up to 45%. Now let us see the test procedure. The mold is stuffed in 3 layers of aggregate. Each and every layer is tampered with 25 strokes. By the round end of the tamping rod. The surplus aggregate should get struck off by the tamping rod. The next weight of aggregate in the mold is measured to the nearest gram.
And the weight is noted as W1. The surface of the aggregate is leveled and the plunger is inserted. Consequently the plunger rests horizontally on the surface. The whole apparatus is then placed between the plates of compression testing machine and loaded at a consistent rate. So it can reach to a load of 40 tons in 10 minutes. The load is then released and the sample is removed from the cup. The sample is then sieved on 2.3 mm IS sieve until no further significant amount passes in 1 minute.
The fraction passing the sieve is weighed to nearest accuracy of 0.1 grams. And the weight is noted as W2. The crushed aggregate W2 is expressed as percentage of the total weight of sample W1. Which is the crushing value of the aggregate. And the crushing value is calculated by using the formula. Aggregate crushing value is equal to W2 by W1 into 100. And the value is expressed in percentage. In aggregate crushing test, if aggregate crushing value is less than 10, it signifies an exceptional strong aggregate. While aggregate crushing value above 35 would normally be considered as weak aggregates.
Now let's see about the abrasion test on aggregate. Abrasion test is carried out to determine the abrasion value of the coarse aggregate by Los Angeles abrasion test. This test is used to find the percentage wear due to relative rubbing action between the aggregates and steel balls used as an abrasive charge. Abrasion test on aggregate indicates the hardness of aggregate. It shows the ability of aggregate to resist wear and tear. Abrasion value of aggregate should not be more than 30% of aggregate used for surface wearing course.
And should not be more than 45% for surface other than wearing course. Now let's see in detail about the test procedure. The principle of Los Angeles abrasion test is to find the percentage wear due to relative rubbing action between the aggregate and steel balls used as abrasive charge. Los Angeles machine is made up of a circular drum of internal diameter 700 mm and length 520 mm. It is mounted on horizontal axis that allows it to rotate. An abrasive charge made up of cast iron spherical balls of 48 mm diameters and weighing between 340 to 445 grams is generally placed in the cylinder along with the aggregates.
The quantity of aggregates usually ranges from 5 to 10 kg. However, it depends upon the gradation of aggregates. The cylinder is then locked and rotated for a total of 500 to 1000 revolutions at a speed of 30 to 33 RPM. Pathways of the You Depending upon the gradation of aggregates. After the above mentioned revolutions, the material is then sieved through 1.7 mm IS sieve. The difference between the original weight and the final weight that is the sieved through weight is expressed as percentage of the original weight of the sample aggregate.
This value is called as Los Angeles Abression Value. The maximum Los Angeles Abression Value should not be more than 30% as I said earlier. It should not be more than 30% for the use of wearing surface and not more than 50% for the use of concrete. Now let's see about impact test on aggregate. Aggregate may be subjected to a sudden shock or impact during as well as after the construction. These loads are different from the gradually applied compressive loads. Due to such kind of loads, aggregate breaks down into smaller pieces. In order to evaluate the resistance to impact of aggregate, the aggregate impact test is conducted.
Aggregate impact value gives the idea about how much impact load can be resisted by aggregate. Actually, aggregate should be sufficiently tough to resist their disintegration due to impact. This distinctive property is measured by impact value test. Toughness is the property of a material to resist the impact. For example, due to the movement of vehicles on the road, the aggregates are subjected to impact. It results in their breaking down into smaller pieces. Therefore, the aggregates should have sufficient toughness to resist their disintegration due to the impact.
This distinct property is measured by impact value test. The aggregate impact test value is a measure of resistance to sudden impact or shock, which may vary from its resistance to gradually applied compressive load. A test designed to evaluate the toughness of stones, that is the resistance of the stones to fracture under repeated impacts, may be called as impact test for road stones. Now let's see in detail about the test procedure. The following procedure is applied to find out the impact value of aggregate. Aggregates for the test sample can be decided by passing it through 12.5 mm IS sieve and retained on 10 mm IS sieve.
The sieved aggregates should be dried in an oven and then filled in a cylindrical steel cup. The cup of the impact testing machine should be fixed firmly in position on the base of the machine. Whole of the test sample is to be placed in it and compacted by 25 strokes of the tamping rod. Weigh. Then the sample in the cup is weighed to the nearest grams and the weighed sample is noted as W1. Also weigh the empty cup, let it be W2. The hammer should be raised to 380 mm above the upper surface of the aggregates in the cup and allowed to fall freely onto the aggregates.
The test sample should be subjected to a total of 15 such blows, each being delivered at an interval of not less than 1 second. Lock the hammer at the top and remove the cup from the base of the machine. Sieve the crushed samples through the sieve of 2.36 mm IS sieve. Weigh this fraction and say it as W3. So now the aggregate impact value is calculated by using the formula W3 by W1 minus W2 into 100. Where W1 is the weight of the sample with cylinder, W2 is the weight of the cylinder and W3 is the weight of fraction passing through 2.36 mm IS sieve.
Now let's see about the soundness test on aggregate. Soundness test on aggregate is conducted to understand the resistance of aggregates to weathering action. Aggregates are subjected to the physical and chemical action of rainwater, groundwater and other impurities of the atmosphere. This can lead to a change in the volume which is not good and substandard for the durability of construction. The property of aggregate to withstand the adverse action of weather is known as the soundness of aggregate. The soundness test on aggregate is carried out to learn the resistance of aggregates to weathering action like thawing, freezing, alternate wetting and drying in normal conditions and in salt water and also in variation in temperature.
When subjected to above stated conditions, aggregates which are weak, porous and contains any irrelevant matters can drastically undergo volume change. If the resistance against weathering action is good for aggregate, then it will have high durability. The durability of the aggregate is determined by this test. So now let's see the test procedure. Let's take carefully graded and weighed test samples of aggregates, soak into either sodium sulfate or magnesium sulfate solution. The sample is then oven dried under specific conditions. The growth of salt crystals in the pores of the test samples is considered to produce disruptive internal forces, similar to the action of freezing of water or crystallization of salt.
After specified number of cycles, loss in weight is measured. As a general guide, after 10 cycles, the average loss of weight should not exceed 12% to 18% when tested with sodium sulfate and magnesium sulfate respectively. Now let's see about the flankiness index test on aggregate. Aggregates are available in various sizes and shapes that is rounded, cubical, angular, flunky or elongated. It is proved that the flaky and elongated particles have less strength, less bonding, less interlocking and durability as compared with cubical, angular or rounded particles of the same size aggregate.
It can be said that aggregates are flaky when aggregates are too thin compared to their average size. Elongated aggregate means aggregates that are too long compared to their average size. Flankiness index test and elongation index test are performed to find flaky and elongated aggregates. Flankiness index test is used to determine the particle shape of the coarse aggregate. The particle shape of the aggregate is obtained by the percentages of flaky and elongated particles accommodated in it. For base coarse and construction of cement concrete type, the presence of flaky and elongated particles are considered undesirable.
It causes inherent weakness with possibilities of breaking down under heavy loads. Therefore, the evaluation of the particles, particularly with respect to flunkiness and elongation is necessary. The flunkiness index of coarse aggregate is defined in percentage by weight of aggregate particles and least dimension of those particles should not be less than 0.6 times their mean area. Flankiness index test is not applicable for aggregate sizes smaller than 6.3 mm. Flunky or elongated coarse aggregates are disadvantages to higher workability and stability of mixes. Now let's see about TIF procedure of test.
Take an aggregate sample of around 200 pieces of any fraction and weigh it. The sample should be sieved with IS sieve specified in the table in the next slide. Each fraction is gauged in turn for thickness on the metal gauge. The total amount passing in the gauge is weighed to an accuracy of 0.1 percentage of the weight of the samples. Gauge each aggregate on length as well as thickness. Take the weight of the aggregates which are retained from length gauge to find the elongation index. And take the weight of the aggregates which pass through the thickness gauge to find the flankiness index.
Calculate the percentage of aggregates passing and the initial weight. This will give the flank rhythm. And calculate the percentage of retained aggregates and the initial weight. It's called the elongation index. This is calculated by using the formula. The Flankiners index on an aggregate is equal to total weight passing Flankiners-Goyce into 100 by total weight of test sample. And the elongation index of an aggregate is equal to total weight retained on elongation gauge into 100 by total weight of test sample. The values are arrived are in percentage. This is this table indicating all the ISC sizes in which the particle is allowed to pass through.
Now let's see about the specific gravity and water absorption test on aggregates. Specific gravity of aggregate is defined as the ratio of the weight of aggregate to the weight of equal volume of water. It is also known as relative density. However, the ratio always uses water as the standard comparison. The density of water is 1000 kilogram per meter cube. Density of all other materials is divided by that of water to calculate the relative density. So the specific gravity shows the strength of the aggregate. Aggregates having a very low specific gravity are generally weaker than those with high specific gravity.
All rocks and stones contain some small amount of voids and the specific gravity is an indirect measurement of aggregate's porosity. A low specific gravity may indicate high porosity and therefore it offers poor durability and low strength. Water absorption of aggregate gives an idea about the internal structure of the aggregate. If aggregates have more absorption capacity, they are called porous in nature. Such aggregates are unsuitable and generally not preferred for any construction. In the aggregates, some of the pores are permeable whereas others are impermeable. There are two types of specific gravities.
One is the absolute specific gravity and the second one is the apparent specific gravity. In the determination of true or absolute specific gravity, both the permeable and impermeable voids are excluded. But it is not of much practical use as the volume of impermeable internal pores is too difficult to determine. On the other side, for the determination of the apparent specific gravity, the volume of impermeable internal pore is added to the effective volume of the aggregate. But it does not include the permeable pores. The specific gravity first depends upon the chemistry of the parent rock and then on the amount of voids within it.
Specific gravity is calculated by measuring the weight of the oven dry aggregate divided by its absolute volume excluding the natural voids in the aggregate. It is the realistic quantified data validated to use the calculation of concrete mix proportion. Now let's see about the importance of specific gravity of aggregates. The specific gravity of aggregates indirectly measures its density. Hence, it is the most essential parameter of strength or quality of the aggregate. It is due to higher specific gravity, there would be higher compressive strength of aggregate and hence it passes on to the concrete.
Lower specific gravity indicates high porosity. Such aggregates are weaker in comparison to the aggregates of higher specific gravity. It is of important consideration that when you deal with lightweight aggregates, some harmful particles are lighter than the good particles in aggregate. Hence, by tracking the specific gravity of aggregates, one can get to know the change of material or possible contamination in it. During the production of aggregates, by using the difference in specific gravity, harmful particles can be separated from the goods by using a heavy media liquid.
In the cement concrete, the percentage of voids and the solid volume of aggregates can be calculated with the help of its specific gravity. In concrete technology, specific gravity of aggregates is essential in calculation of compacting factor in connection with the workability measurements. Looking on to the above importance, one has to reasonably cautious while using lightweight aggregate and its impact on compressive strength of concrete has to be counted in detail. Now, let's see about the test procedure for specific gravity and water absorption on aggregate. Take a sample of 2 kg of aggregates.
Wash the sample thoroughly to remove finer particles and dust from it. After washing, place the aggregates in the wire basket and immerse it in distilled water at a temperature between 22 to 32 degrees C centigrade with a cover of at least 5 centimeters of water above the top of the basket. Immediately after immersion, remove the entrapped air from the sample by lifting the basket containing aggregates 25 mm above from the base of the tank and allow it to drop again. Continue this process at least 25 times at the rate of about 1 drop per second.
The basket and aggregate shall remain completely immersed during this process as well as for a period of 24 plus or minus half hour afterwards. Then the basket and the sample are jolted and weighed in the water at a temperature of 22 to 32 degrees C. If it is necessary for them to be transferred to a different tank for weighing, they are jolted 25 times as described above in the new tank before weighing. The weight of the aggregate and basket in water is noted as A1. After that, remove the basket and aggregates from the water and allow to drain for a few minutes.
After that, empty the aggregate from the basket on the dry cloth and return the empty basket to the water. Jolt it 25 times and weigh in water. Note down the weight of the basket suspended in water as A2. Gently dry those aggregates with a dry cloth. Transfer the aggregates to the second dry cloth if the first one is not able to remove the optimum moisture residue in that. After that, spread out them in one layer for at least 10 minutes for the surface to dry completely and avoid direct sunlight on them.
Then take the weight of these dry aggregates which are saturated and noted as P. Next, place the aggregate in the oven on the shallow tray at a temperature of 100 to 110 degrees C and maintain this temperature for 24 hours. Then remove the aggregate from the oven and cool it in an airtight container. After that, measure the weight of the aggregate and note down this weight of oven dried aggregate as C. The specific gravity of aggregates used in construction ranges from 2.5 to 3 and water absorption ranges from 0.1 percentage to 2 percentage.
Now calculate the specific gravity, apparent specific gravity and water absorption of aggregate from the values noted. Now the specific gravity is equal to C by B by A that is weight in grams of the oven dried aggregate in air by weight in grams of the saturated surface minus dry aggregate in air minus weight in grams of the saturated aggregate in water. Now the specific gravity is calculated by C by C by C minus A and water absorption is calculated in a percentage of dry weight. That is 100 into B minus C by C where A, B, C is as indicated below.
From this formula we will be able to calculate the specific gravity, apparent specific gravity and water absorption of aggregate. Now let's see about the bitumen addition test on aggregate. The importance of bitumen addition test on aggregate determines the addition of bituminous binder to aggregate in the presence of water. Bitumen gets well bonded to all the normal types of road aggregates provided they are dry and free from dust. In the absence of water there is no addition problem in bituminous construction. Addition problem arises when the aggregate is wet and cold.
This problem can be dealt by removing moisture from the aggregate by drying and increasing the mixing temperature. For finding bitumen addition, the stripping value test is conducted. Stripping value of aggregate is determined as the ratio of the uncovered area observed visually to the total area of aggregate which is ultimately expressed in percentage. This stripping value should not exceed 5%. Now let's see about the test procedure of bitumen addition test on aggregates. Take a sample of 200 grams of dry aggregates passing a 20 mm ISC and retained on 12.5 mm ISC and 5% by weight of bitumen binder.
Mix the binder and the aggregates till they are fully coated. Then transfer the mixture into a 500 ml beaker and allow to cool at room temperature for about 2 hours. Next add distilled water and immerse the coated aggregates. Cover the beaker and keep it in a water bath for 24 hours. Now take the beaker out and let it cool at room temperature. The uncovered area needs to be visually observed. Like I said earlier, the stripping value of aggregate is determined as the ratio of uncovered area observed visually to the total area of aggregate which is ultimately expressed in percentage.
And this percentage should not exceed 5%. Thank you. Thank you. Thank you. Thank you. You