Lesson finished
Up next: Typical EDS Design Flow from Logical Architecture to Harness Drawing
Unlock all 44 lessons of Automotive Wiring Harness using CATIA V5Full course ₹40,000 · paid
Wiring Harness Components: Wires, Connectors, Terminals, Clips
A free lesson from Skill-Lync's Automotive Wiring Harness using CATIA V5 course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Wiring Harness Components”
What will you learn in this free Automotive Wiring Harness using CATIA V5 lesson?
The instructor lists the components of a wiring harness and describes each in turn: copper wires with PVC insulation, connectors and their parts, terminals and their plating, insulation tapes, and clips and clamps. The lesson ends by summarising the function of each component, including grommets, fuse and relay boxes, retention devices and guiding channels.
- Connector parts: housing, wedge lock, seals and cavities
- Terminal plating: tin, silver and gold
- PVC versus cotton tape, and where cotton is used
- Clip types: push-fit, fir-tree, edge and separator clamps
What comes after lesson 2?
The next free lesson is lesson 3, “Typical EDS Design Flow from Logical Architecture to Harness Drawing” (22 min). Later in Skill-Lync's Automotive Wiring Harness using CATIA V5 course (paid): lesson 4, Wiring Harness Routing and Packaging; lesson 5, Customized Settings for Wiring Harness Assemblies in CATIA V5; lesson 6, Electrical Part Design. The full course has 44 lessons (18 h 44 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Now let's get a more detailed introduction to the wiring harness. So wiring harness is an assembly which consists a lot of different components and those components are used for a different purpose to perform different functions into the wiring harness. Wiring harness as an assembly don't have its own function. It is just a media between different systems, subsystems or components of electrical system which is used to pass the signals, power, information and ground signals or ground power through the wiring harness. So here are the different components which are used in the wiring harness. As the name suggests, wires are the part of the wiring harness assembly followed by connectors, terminals, protection coverings, insulations, clips and clamps, fuse and relay box, retention devices, guiding channels and electronic components.
There could be some other components which could be very specific to the different OEMs. But these are the very widely used components in the wiring harness assembly. So let's see one by one what are those components and how they look. So let's start with the wires. So let's start with the wires. So wiring harness consists of various wires bundled together with each individual wire responsible for carrying an electrical signal and energy used in different system or different circuits. Few examples are given here like starting the wires.
Few examples are given here like starting the engine, lighting system, the meters, the navigation system, the power windows and doors or any other electrical devices used in the vehicles. Now these names are given just for an understanding but these are not limited to these loads because there could be many many electrical devices loads used in the vehicle electrical system. So these wires are basically the copper conductor insulated with the PVC insulation. PVC is basically the plastic material which is used to cover the copper conductor to protect the conductor during the flow.
So there are also initiatives in the industry to use the aluminum wires to get the benefits of weight and cost reductions. But those are under evaluation are and are not completely deployed into the automotive world. So for now copper conductors are very widely used into the automotive wires. Moving next to the connectors. So what are the connectors? So an electrical connector is an electromechanical device used to join electrical termination and create an electrical circuit. So electrical connector consists of housing, terminals, wedge locks, seals, cavity and mounting caps which are basically used to mount the bigger connectors into the component housing body.
The terminals and wedge lock seals are the integral part of connector or it can be fixed into the connector. Those are also referred as a different components into the wiring harness. The reason behind it is the selection criteria for these parts are different than the main selection of the connectors. So just to give an example, if I need to select the terminals. So there are many criteria that should be specifically reviewed before the selection of terminals. So there are many terminals available to use along with the single connectors.
So if I have X connector, I could have 10 numbers of terminal which can be used along with that X connector. The selection of that terminal is basically depends on the application and the criteria that you are expecting to perform in terms of the electrical properties and the mechanical properties. So this we are going to discuss in later slide which talks about the performance and the selection criteria of different wiring harness components. So the connectors are basically the plastic molded parts along with the locking and retention features in it.
So you can see in picture there are different connectors shown onto the screen. So in bottom row right hand side connector is along with the cam which is referred as a mounting cam in a definition. So in case of very big connectors, the cam assembly is used to fix the connectors with the mounting body. So that it will ensure the perfect mechanical connectivity and the electrical connectivity between wiring harness and components. As it definition says that it is electro mechanical device. It means it ensures that it makes the electrical connectivity as well as the mechanical retention or mounting features in its housing.
So there are many different locking mechanisms used to mount the connector with the mounting devices. So most of them are the snapping time features or the cam face type features. These connectors also comes with the wedge locks which are referred as a secondary lock in later slides. The seals which are used to secure the connections from the water and dust ingress. The cavities which are used to mount the connector mounting clips. So that the interconnection can be parked and packaged to secure the joints and the mounting cams as we discussed.
Moving next to the terminals. Now as I explained though the terminals are also part of the connector assembly. But because of their different selection criteria and different shapes and applications. This falls under the separate category into the wiring harness. And these are also very crucial components of the wiring harness. The wiring harness cannot be completed without the terminals and connectors. So by definition terminals are the device designed to terminate a conductor that is to be affixed to a post stirred chassis or another tank etc. To establish an electrical connection.
This includes the connection to the components as well. So terminals are made of the metal mostly the brass. And it will be plated by the different electroplating materials. Like tin plating, silver plating and gold plating. So the logic behind using of a different plating is to secure the joints from the environmental conditions. And to provide the minimum electrical resistances. It means the gold is most secure and most anti-corrosion plating. And it provides the lesser electrical resistance compared to silver and tin plating. Now its name says that gold platings are used.
They are very expensive and expected to use for very sensitive loads. Where very low voltage signals are also being monitored. The best example to use the gold plated terminals is air back connections. In case of high current circuit. It is not advisable to go for either silver plating or gold plating. The tin plating should meet the purpose of the use of the terminals. Moving to the next component. Which is also very crucial part of the wiring harness assembly. Which is the protection device. So in protection devices there are many components used as a protection device.
Let's look at the corroborated tubes. So corroborated flexible tubes are also known as cot tubes or conulated conduits. It have a wide range of application in automotive industry. Corrugated tubes are made from the plastic material. And they are very flexible in nature. To ensure that there is a flexibility for wiring harness bundle to run across the vehicle. These tubes are used to protect the harness from thermal and physical damage. And to sometime it is also used to improve the wiring harness appearance. So just to give an example of thermal and physical damage.
The corroborated tubes are used to protect the wires from the high temperature. And to give the example of physical damage. Corrugated tubes are used to protect the wires from the sharp edges of the metallic components. Harness appearance is taken care by corroborated tube. By covering the different colors of wires. So that it will give the uniform appearance of the wiring harness. For example there are multiple colors of wire bundled together. Like red, green, white, blue. Then it will look very odd. If you only tape and leave them like that.
Whereas if you apply the corroborated tube on those wires. It will have a uniform black color or any other colored cut tube. To improve the appearance of the wiring harness. The corroborated tubes are available in many colors in many sizes. And with many different temperature ranges. So sometimes the yellow cut tubes are used to indicate the wiring harness. Which is used for highly safety related systems. Such as airbags. So some of the OEM advise to use the yellow corrugated tube on the wiring harnesses. Which are used for the airbag system.
So protection coverings are flexible. They are temperature, wear and tear resistance. And those are the molded plastic or polymer parts. So sometimes we use the silicon polymer coverings. In case of very high temperature near to the exhaust. So silicon tubes are available up to 300 degree Celsius. Where they can protect the wiring harness. But it is not advisable to route any wiring harness in such environment. So another example of protection devices is a sealing grommets. So grommets are the rubber molded parts. And they are used for mainly three purposes.
For sealing, protection and to absorb the vibrations of the shocks. You can refer the following images. The first image of left hand side. It is used to basically to show the application of grommet to provide the ceiling when wiring harness is passing through the dry zone to the wet zone. So these grommets are used to block the flow of water or the dust through the holes which is provided to pass the wiring harness from one zone to other zone. Whereas the middle image shows the edge protection, the shown wiring harness is used to enter into the tailgate door and it will have the sharp edge with the cutout.
So grommets helps to protect the wiring harness from the sharp edge by providing the positive fixing on the edge itself. So there is guarantee of the positive clearance between the sharp edge and the wiring harness. The right hand side is very rare case where the grommets are used for the shock or the vibration absorption. So this is example of wheel spirit sensor. Wheel spirit sensor is fitted on the vehicle hub which is subjected to the vibration because of the shock absorption. So the grommets are used which is parked on the firm back edge to absorb those shocks.
So there are wide applications of grommets and the wide purposes of the grommets which are fulfilled to protect, to decorate and to make the wiring harness assembly safer. As I said the protection grommets are rubber molded components using wiring harness for the protection as respect above. The next protection device is insulation tapes. So though it is very simple understanding of the insulation tape but it plays a very important role in the wiring harness assembly. The material and the grates of the automotive wiring harness insulation tapes are different than we use in daily uses.
So there are mainly two types of insulation tapes used. One is the PVC insulation tape other is cotton insulation tapes. The left hand side image shows the PVC insulation tapes which are available in a different colors whereas the right hand side image shows the cotton tapping which is also available in the many colors. So the main purpose of insulation tapes are to form the bundles or to align the wiring harness in a systematic arrangement so that it will form the perfect bundle in a circular shape.
The cotton tapping application is mainly demanded when there is a high temperature like engine area. Cotton tapes are very high temperature resistance and they are very effective in high temperature zones. Insulation tapes are available in adhesive and non-adhesive like sleeves. Non-adhesive sleeves are used to protect the harnesses. They are made of the cotton or polymer materials. The next is about the clips and clamps. So there are a variety of the clips and clamps available in the market to mount the wiring harnesses. So these are the few examples of clips and clamps or a few categories of clips and clamps but these are not limited to the use.
The more you explore the more the options you will get for the wiring harness fixing and clipping solutions. Let's look at the standard cable strap type clips. So we have simple cable tie which are used to mount the wiring harnesses with some metallic bracket and these are also widely used in our daily life. Then we have push fit in hole type clips. So there are two types of holes we can have to mount this clip. One is round type holes and other is anti-rotational type holes.
The round type holes are not anti-rotational because once you mount the clip it can be rotated whereas in case of anti-rotational once you mount the clip, clip will not move. So in round type clips also we have furtree type clips and anchor fit type clips. The furtree type clips joints are more firm than the anchor fit type clips. Same types are available in anti-rotational clips. Whereas we can also have clips which are suitable to fix into the studs then edge of the panels. If stud edge and the holes are not available then you can also go for sticky clamps.
Use of edge clips and sticky clamps are not suggested or not recommended because in case of edge clips once you push the edge clips onto the edge it will make a scratch edge and it will remove the coating which is provided onto the panel. That can lead to the corrosion in long run and the corrosion cannot be repaired and it will be permanent damage. Also edge clips are more costly compared to the other types of clips. Whereas the sticky clamps are not reliable solution because the stickiness of surface can be affected in long run because of dust and water interfere or because of other environmental conditions.
So apart from standard cable strap we have option of separator clamps. So the name suggests separator clamps used to separate the wiring harness from something. So these types of clamps actually used when we have wiring harness routing along with some hoses, pipes or two wiring harnesses are routed together. So these types of clamps are used to maintain the specific distance between two running wiring harnesses or two running wiring harnesses and the pipes. So these are available in two types, panel mounted and wire to wire. So panel mounted can be mounted onto the any body part and those are available in the same types like hole mounted, stud mounted, it can be bolted, you can have edge mounted and these are available in different combinations.
Like separator clamps can be used to mount two wiring harnesses, three wiring harnesses or multiple branches or the bundles which are running together or the combination of wiring harnesses, pipes, hoses to make the positive clearance and to ensure the proper routing of these parts in the vehicle environment. These are also available as in wire to wire to wire clamps where the mounting to the panel is not provided. So this is also used to ensure the positive clearance between the different components which are routed parallel. Now as I said this application of these clamps are very wide and it can be used in each and every area where the wiring harnesses dressing is more important, wiring harnesses mounting along with the other components with the positive clearance is important such as wiring harnesses routing along with the breakwaves.
These are again the plastic molded parts along with the different types of snapping features provided into the mold itself. Whereas the manufacturing process for the edge clips are little different which calls for the plastic molding and the metallic insert into it. Moving to the next component used in the wiring harness that is fuse and relay box. So fuse and relay box are again the plastic molded parts used to package fuses and relays in a systematic manner. It is also intended to protect the fuses and relays from any damage like physical and environmental.
The shown figures are for the fuses and relay boxes where you can see the relays and fuses are mounted into the plastic housing body where it comes with the different types of terminals or connection joints which will make the connection between the fuse and the wiring harness. This comes in a different options like wire entry drive, connector based and these are also come as a sealed and non-sealed components. The selection of these fuse boxes are always driven by the number of fuses and relays required in the electrical system.
The area where this fuse box is mounted and the cost available for the fuse box or the wiring harness. So moving to the next part of the wiring harness assembly which is the retention device. There are many types of retention devices used in the wiring harness such as connector mounts, secondary locks, connector back sets. Those are shown in the pictures. These are again the plastic molded parts available with the many varieties and many options. So let's talk about the first part connector cavity or connector mounting clip.
So these are basically used to mount the interconnection connector to the body to ensure that wiring harness connector is not loose and it won't rattle in case of vibration or during the running conditions. This ensures the positive fixing of interconnection connector onto the body. Sometime it is used for the component mountings also. The second part is secondary lock which is used to ensure the secondary locking of terminal. So as name suggests it is a secondary locking the question could be what is the primary locking. So the primary locking is always provided with the terminal itself where it is again part of the connector plastic housing.
So secondary lock is always an additional arrangement to ensure that terminal backouts failures are minimized. Again secondary locks are not mandatory parts in the wiring harness but designer can decide whether secondary locks are essential based on the system complexity and the function the system is performing. For example if the systems are safety it is advisable to go for the secondary lock connectors. The third type is the back cells. So the back cells are basically the dressing devices or the packaging guiding devices which are used at the end of the connectors.
So the main purpose of back cells is basically to guide the wire in case of the very constrained packaging area or to provide the better appearance at the end of the connector which is shown in the images. So there are many types of back cells available. Accounting soi-plus牛-chanicalacha you will do also? After that are available, if we built Mr. Patriots the power of America the power of Canada So this can take more money only. This can place the most available since April Erst psychologist. And now in fact we start this one.
Like L-Type Backsells, Y-Type Backsells, or Angular Backsells, and the Straight-Type Backsells. Some examples are shown on the screen. Moving to the next device, the Guiding Channels. The Guiding Channels are always customized and it is again developed basis the decision by the design engineers. Now the Guiding Channels are used in the area where wiring harness packaging is very crucial, it is visible, or the packaging area is very tidy. As I said, these are the customized parts. They need a lot of tooling costs and the development costs to use into the wiring harness.
So, it is really required to ensure the application and the need of these guiding channels in the specific area. So, Guiding Channels are plastic molded or metal parts designed to guide the harness bundle in the given geometry area to secure and protect the harnesses. You can see the example of the engine wiring harness shown in the images. So, there are two channels used in the left-hand side wiring harness, which are used to guide or to protect the wiring harness in two different areas. Whereas, the right-hand side image shows the application of one of the guiding channels onto the engine.
Now, that Guiding Channels is used to guide or protect the wiring harness, which is used for the injector and few sensors, which are placed near to the injector like rail pressure sensor and rail temperature sensor. Since this area is visible and it can be easily seen by the customer, it is very required to keep it systematic, well packaged and better in aesthetic appearance. So, use of channel in this area is justified and it is advisable to develop the channel for such areas. So, moving to the next part, which are the electronic components used in the wiring harness.
So, these are not the essential parts of the wiring harness, but sometimes it is the part of the wiring harness. Now, the increase in the complexity in the automotive world, these parts are very common, which are supplied along with the wiring harnesses, such as diodes, terminating register, the flashers, which are used for the turn indicator operation, different timer circuits, which are sometimes part of the safety systems of the vehicle, are being supplied with the wiring harnesses. As you can see in the images, the left hand side images of terminating register, which will be supplied along with the wiring harnesses and it will look like connectors, but it is really required to ensure that these are packaged properly and these are kept in the right environmental conditions, which will not cause the variation of their properties in different temperature ranges.
Diode packs are also used in the form of the wiring harnesses and those will be supplied along with the wiring harnesses and those will be supplied along with the wiring harnesses. Most of the controllers are fitted along with the fuse and relay boxes so that one can ensure the properly and securely packaged conditions of those electronic controllers and it also gives the easy accessibility in case of filler analysis. So, these are the different parts which are used in the wiring harnesses, as I said, each and every part is very important and they have performed the different important roles into the wiring harnesses.
So, let us look at the roles they are performing or the functions they are performing into the wiring harnesses. Few of them we have already discussed, but let us revise them. So, the first component is wire. So, wires are responsible to carry the electrical power from one end to the other end by providing the minimum resistance. Copper is widely used as a conductor in automotive harnesses. Connectors are responsible to make a contact between wiring harnesses and components or between two different wiring harnesses assemblies by offering mechanical locking and sealing to the joints.
So, connectors which are connected between two different wiring harnesses are called as an interconnection or in-line connectors. Terminals are crimped joints to wire to make a mechanical connection with the connector and device more reliable and durable. Terminals are electroplated to offer minimum contact resistance and anti-corrosion protection. It also forms the electrical contacts between device and the wiring harnesses when it comes to the joints of the connector. So, all the electrical contacts made between the connector and the devices or connector of the different wiring harnesses, those are made through the terminals.
Protection devices used to protect wiring harness assembly from mechanical damage and thermal damage by any means in vehicle environment. Grommets are part of a protection device which are aimed to use to protect harnesses from physical damage from water and dust ingress and to absorb shock fatigue or vibrations. Insulation is adhesion taping made by PVC or cotton material to form harness bundles. Cotton tapes are used to protect the wires in high temperature areas. Clips and clamps are basically used to fix wiring harness bundles by providing the positive fixings which will ensure the securing of the harness bundle and the desired wiring harness routing part into the given vehicle environment.
Fuse and relay box are used to provide the secure and protected fixings for fuses and relays and those are responsible to provide the very durable and reliable low resistance and sealed connection to all the devices which are fixed into relay and fuse box. Retention devices such as connector mounting clips, connector secondary locks are used to provide mechanical fixing locking to the connectors and terminals. Connector back cells are used for a good appearance and bundle dressing in case of critical areas as we discussed. Guiding channels are responsible to guide and protect the harness bundles in critical packaging area like engine.
Guiding channel could be of plastic or metals. Electronic components like diodes, thermating register, controllers which are part of harness supply should play the role as defined in logic. The role of electronic components are not defined by the harness or it is not used for protection but it is always a demand of logic which is defined by electrical system engineers. These are not the necessary parts in the wiring harness but looking at the complexity increase many electronic components are being supplied along with the wiring harness. Note 2 6 6