Lesson finished
Up next: Geo and Re-Spot Pin Tolerances, Clamps, Grippers and Terminology
Unlock all 41 lessons of Automotive BIW Fixture Design using CATIA V5Full course ₹40,000 · paid
Body in White Basics, Fixture Types and BIW Assembly Stations
A free lesson from Skill-Lync's Automotive BIW Fixture Design using CATIA V5 course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to BIW and Fixtures”
What will you learn in this free Automotive BIW Fixture Design using CATIA V5 lesson?
The instructor defines body in white, lists its main parts (body sides, underbody, closures, roof, fender) and explains what a welding fixture does. The lesson covers production, pre-production and checking fixtures, restricting degrees of freedom, and how an assembly line splits into zones and tools such as geo, re-spot, marriage and framer.
- What body in white means and its main parts
- Production, pre-production and checking fixture types
- Restricting degrees of freedom to locate a workpiece
- Roles of geo, re-spot, marriage and framer tools
What comes after lesson 1?
The next free lesson is lesson 2, “Geo and Re-Spot Pin Tolerances, Clamps, Grippers and Terminology” (38 min). Later in Skill-Lync's Automotive BIW Fixture Design using CATIA V5 course (paid): lesson 4, Understanding Different Welding Processes; lesson 5, B Fixture Design; lesson 6, Week 3: Design Methodologies - Session 2. The full course has 41 lessons (16 h 52 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello everyone. So we'll start with our first session that is introduction and we'll be covering the topics that is the definition of the BIW jigs and fixture, BIW nomenclature, BIW stations and their use in basic terminologies. Moving on to BIW. What is the BIW? From where does that name BIW is derived and what is the importance of this name? So BIW is nothing. It is body in white that refers to the welded sheet metal components which form the vehicle structure to which other components will be married that is engine, chassis, exteriors and interior teams. So BIW is just a welded structure where different components from the side of the body, the rear of the body, the under of the body or the upper everything is joined together where other parts of the car like the engine, the chassis system or the transmissions, doors, dashboards and everything will be structured on. Also body in white of BIW refers to the stage in automotive design or automobile manufacturing in which the car body in which the car body sheet metal including doors, hoods and deadlifts has been assembled or designed but before the components that is chassis and motors and trim like windshields, seats, upholstery, electronics, etc. have been added. And this name BIW is derived from the fact that after the welding is done and before painting, this body is submerged into a liquid called primer. It has some grayish color and from that it is derived as a body in white So there are different categories in which BIW is categorized. The main parts being body sides, under body, closures, roof, fender, etc. So body sides, we have body side outer or inner like the right side and the left side of the car body. So inner side of the car body or the outer side of the car body are the body sides.
Same under body. So we have front and under frame like the engine compartment where the engine has been assembled. Throughout the main floor where the seats and everything will be mounted and the rear end room where the rear compartment is there. Then we have closures. Closures comes as in the doors, both the doors, front doors, the rear doors, front hood, deadlifts, trunks, etc. Then we have roof. Same goes with the roof, the roof inner part and the roof outer part. And the fender. And the fender. Fender is the area or the part above the wheel which is connected with the hood and tail lights and the side wardens.
So if you could see like there are different parts of BIW structure that has been known for your reference so that you could have some ideas about the different parts that are called in BIW structures. These are the basics named and how are they called in the UK or US. So like we have inner wing panel, the upper wing member, the suspension tower, the A pillars, wind string head to tail and a second goes on. So these are the major parts that form a BIW structure for car body and how are they named in the automotive industries.
Now let's move on to fixture. Fixtures will be discussing everything about those basic definitions. What are the different parts of fixtures, different types of fixtures, different BIW stations and how, what is the basic principle of designing a fixture. To start with the definition, a fixture is a device which holds the workpiece to be processed that can be as a welded, glued, fastening, revetting, etc. by using 3 to 1 principle. It means for designing a fixture is a principle called 3 to 1 principle, which ensures the basic parameters of the fixtures are set, basic requirements of the fixture are properly achieved.
Right. So in general, a welding fixture or a welding tool consisting of N number of units together to hold the car panel and is mounted on a base unit. That is generally, you can also define a fixture as an assembly of different types of units assembled together on a base unit. So welding fixtures are normally designed to hold and support various components that needs to be joined together or welded together. So in an assembly, we have different parts that needs to be welded together to form an assembly to get proper profile and dimension relative to each other as per design.
So it is necessary to support them in a proper location which is capable of preventing distortions in workpieces during welding. If you declamp some part after welding, there will be some distortions. So fixture ensures that there will be the minimum or negligible distortion that come out of an assembly so that it won't affect the final assembly or final outcome of a car body in aspect of aesthetics or in aspects of dimension or in aspect of rigidity or strength. For this, for this, the locating element needs to be placed carefully, clamping has to be light but firm.
Placement of clamping elements has to be clear of the welding area and the fixture has to be quite stable and ready to withstand the welding stresses. We will be providing some locating elements. They will ensure that every time the repeatability of assembly should be same. It won't change after one operation or two operations. So for that, we will be providing some elements and the clamping needs to be very light and firm. The clamping should not be as hard that it is defecting the panel. It is wearing, tearing the panel or denting the panel.
It should not damage the panel. And it should have adequate force that it could hold the panel so that after the welding is being done, there won't be any deformation. Also, all these things like the clamping, the locating elements and everything that needs to be cleared off from the welding area so that an operator or maybe robot should not get any interruptions while moving through to get a part welded or joined together or for any other processes. That needs to be very much made sure while designing.
You will have to check in your design like welding area is very much cleared off from any part of the fixture. There should not be any interruptions while a process needs to be done. Also, fixture should be so rigid and should have that stability that it could withstand the various vibrations and other effects due to welding stresses. It should not be like that the fixture can be able to vibrate. So, we need to fix our fixture and we need to keep our fixture stable for a longer period of time.
So, there are some general types of fixtures that are defined in these three categories. The first is production fixtures. The second is pre-production operation fixtures. And the third is checking fixtures. A production fixtures, as the name suggests, it is basically used for the mass production purpose. And it is the fixture from where our car or car body will be assembled together and will go to the end customer. So, the materials used in this production fixture should be properly tested. The hardness level should be tested. The aesthetics should be tested.
And the quality of the fixture as relative to the dimensions, the tolerances and everything should be maintained. And it should be easy approachable for maintenance purpose because a fixture needs to be maintained after a few certain period of time. Like after a V or so or 10 days or 15 days, there needs to be maintained of that particular fixture. So, it should be accessible for maintenance purpose also. So, if you're talking, if you're designing a fixture, a production fixture that has to go for production from mass production, it should have those parameters that it can be easily accessible for maintenance people or maintenance person so that he could assemble and disassemble that particular fixture easily without consuming most of the time.
Now, if you talk about the pre-production operation fixture, this fixture is generally designed as a prototype fixture for initial batch production to study the feasibility and to make any improvement that needs to be done for production fixtures. So, this is the base fixture for a production fixture that set a benchmark and criteria and help us to rectify the errors that we could get from pre-production operation fixture. Because in pre-production operation fixture, there will be more involvement of manual operators, there will be more involvement of engineers and quality and it will have a larger cycle time than the production fixture.
So, this will actually be our base line for designing of production fixture. But we don't actually practice first designing a pre-production fixture, then manufacturing and then going for production fixture. Because it is very time consuming and it takes a lot of cost and we need to, the basic, one of the most important parameters of fixture is also that we need to keep the cost of the car as low as possible. Fixture fixture is a part of tooling if we are talking about BIW and whatever things incorporates in BIW, it mostly come out of the tools that are used to manufacture those.
So, we need to design our fixture in as less cost as possible so that the final cost of the car can also be minimized as possible. So, we directly go for production fixture, we directly, we keep in mind all the parameters and checklists, standards and everything that it could be used as a production fixture without any flaws. The third is checking fixture. Checking fixture is, as the name suggests, it is basically used for checking or inspecting an assembly that has come out of a geo fixture.
So, checking fixture is very much similar to geo-fixtures, except in this there are no operations are being done like welding or gluing or any other thing. Instead of that, we use different type of in-built fixture gauges or external gauges to check various dimensions and gaps and relative dimensions and tolerances and etc. These all data will be compared to the data. Provided by the designer or the design team of that particular assembly or car assembly and then it will be checked through the tolerance level whether the dimension that has been achieved through checking fixture are in tolerance or not. Also in checking fixture we check like if an assembly is if we are talking about three or four parts of assembly and it has been assembled in a geo fixture now we are taking that assembly to the checking fixture.
So we will try to fix two pin position or locating position locating elements and all the other parts of the assemblies can be checked through some gauges whether they have been welded at exact position or not. This is the main criteria of checking fixture. Moving on. So what is the principle of fixture design? It's a very basic principle for designing a fixture. What happens? Like the main motive of the fixture is to hold it the workpiece so that it cannot move or it cannot distort. After some operations being done after some operations being done. So it has to very much stably and rigidly hold that workpiece. The basic principle is to get or make a body free from various degrees of freedom.
As our understanding as we could see in the images a body has 12 degrees of freedom. 12 being 6 translational degrees of freedom and 6 rotational degrees of freedom. So if you are talking about 6 translational degrees of freedom they will be plus x minus x plus y minus y plus z and minus z. That is translation motion of freedom of freedom. That is translation motion in x, y and z axis either on the positive side or on the negative side. Then we have 6 rotational degrees of freedom. That is clockwise rotation around x axis, anticlockwise around x axis, clockwise around y axis, anticlockwise around y axis, clockwise around z axis and anticlockwise around z axis.
That is clockwise and anticlockwise around z axis. So in order to design a fixture we need to make sure that all these degrees of freedom are to be restricted. There should be 0 degree of freedom of that workpiece. What does it really mean? Restricting a degree of freedom means you are restricting a motion in that particular axis or in that zone. So if I am talking about restricting translation motion in plus x it means my workpiece cannot move in plus x direction whether external force is applied or not.
So fixture is designed in such a way even if some external force is applied my workpiece will not move in any direction or it may not rotate through any axis. This is the basic principle. So concluding that we must fix all 12 degrees of freedom in order to locate the workpiece in the fixture. So 12 degrees of freedom of the workpiece need to be fixed and thus we can achieve 0 degree of freedom for the workpiece. Talking about BIW assembly line. What is an assembly line? The assembly line is in where the different types of panels are joined together in each specified zones.
Each panel categories will have individual zones as underbody zone, door zone, hood zone etc. So we cannot assemble all the car bodies at one station or at one space given space. Okay. So we subdivide our car body like as I have told in the section BIW nomenclature that the car body is mainly divided into different categories. Side bodies, underbodies, upper body, rear body and the front body. Each compromising a set of assemblies together. So we have different zones for each specified category of a car body. Like if you are talking about the underbody zone.
So underbody will have n number of parts and n number of assemblies that needs to be welded together. So we will have a zone where all the assemblies of the underbody is being done. Then we have the side bodies. Side bodies will also have different assemblies and number of parts. There will be A pillars. There will be B pillars. There will be C pillars. There will be reinforcements and etc etc. So they need to be welded together at different different stations. So at one station I am assembling A pillar. At one station I am assembling B pillar. At one station I am assembling C pillar.
At one station I am assembling Fender. So there will be different stations. Okay. Subdivided. And now these all sub-assemblies will be joined together and then the main output of that side body zone Will be completed and will come to the main line zone or main body zone So in such way we divide or divide our assembly line so that there will be proper flow of inventory It should not be like that under body has been manufactured But now my station is idle because sideboard is not prepared or manufactured So we need to ensure that cycle time the time line should met each other like if I need one right side one left side body For assembling a car at the same time I want an under body and front and so I need to make sure that all these are coming together at particular Station or marriage station there will be no idle time again because if you are losing time if my station is being added It means I am losing money. That is why it is very much important to Synchronize all your lines assembly lines and all your zones and all your stations That is why the requirements come for increase in cycle time We increase the number of fixtures for same panels and everything now coming to the assembly line So assembly line will have different zones as I said like under body zone, row zone, hood zone, side body zone Floor zone etc and those each zone will have different stations so like if I'm talking about under body zone to under body For assembling an under body it means I'm assembling floor panel so in floor panel will have different assemblies front floor panel real floor panel Then we'll have cross members then we have reinforcements and everything so all those all things cannot be welded together Okay, we cannot get in hundred as a parts and assemble together in a fixture that is Not very much acceptable and that is not quite feasible because then it will require that much number of pins That much number of clamping that much of resting and we won't get that space So what we do we subdivide into sub-assemblies so now under body can be subdivided into sub-assembly so there will be a station one where let's say front Floor panel will be assembled with reinforcement or cross members then we'll have another stations where real floor panel will be assembled with the cross members and Reinforcements and etc etc and then we'll have the geostation then we'll have the re-spot station everything so Then all these will be subdivided will be a we'll be having different stations for each zone so there will be tools grippers stains and some miscellaneous miscellaneous stations if talking about the tools the basic tools that We require for assembly process are the geo tool re-spot tool marriage tool fair framer tool etc Geo tool is nothing but a tool where in a geometric of an assembly is defined and in a such a way that it should not Deform once the clamping is open it should not deform due to Welding stresses and all how does geo tool and re-spot are differentiated what happens let's say if we have an assembly okay, and We have you say hundred number of spots Okay in that particular assembly now if I am doing hundred spot in one session So it means it will take that much of time So my other stations will be idle if there are let's say if some at another station there is a Combining assembly and it only has 40 spots So my dead station will unless and until I get one assembly from this particular geo tool So what we do we divide those spots so now we choose only those spots from all hundred spots that can assure that my Assembly will not deform after I take out from it for extra after welding is being done So let's say I chose 40 spots from out of hundred spots and now I am doing 40 spots in geo tool So those 40 spots are those spots which are ensuring that the profile and Assembly is as per the design and as per the dimensions and the remaining 60 spots that can be redo in the e-spot tool So my line will not be idle now My station will not be idle by the time my re-spot is being done one more unit or assembly is complete at my geo Tool so cycle will continue so now I have divided the cycle time so yeah So this was a geo tool and re-spot will be discussing more in brief in the next segment marriage tool Marriage tool is a station or a fixture where marriage of side bodies under body front and rear body are done Marriage as in they all the side bodies the under bodies they get assembled together in their particular zone And then they come to a particular station where their assembly will be done through and different joining process through gluing welding Reveating etc Now frame a tool the station just after marriage tool is a frame a tool and this roof will be attached to the output of a marriage tool So whatever will be the output of the marriage tool that will go to the frame a tool and the remaining parts like the roof of the biw We will be attached to it and it will now form a frame and so the name arise as a frame a tool We will also have grippers in each stations Grippers are mostly if they are actually a fixture with frame like structure and we try to put as less weight as possible We try to keep the weight of that fixture as minimized as possible so we use Aluminium frames or steel frames or square tubes and other items that require less space and way less as this is done because the grippers are to be Mounted on some means can be mounted on Robots or they can be mounted on so servo system which can move the gripper from one position to another So the grippers are different are of different types like the material handling grippers the process gripper or combo gripper each gripper compromising to different set of work like material handling as the name suggests it just handles the material like It will pick some assembly from one station and drops it at some other station Now if we're talking about the process gripper so it will do some process like on a fixture there is a assembly is there so This gripper can do gluing, it will have a glue gun attached to it, it can do welding, it can have a welding gun attached to it or different thing.
Combo grippers, when a material handling gripper and process grippers are combined together like when from the same gripper I can do material handling like picking up panel and dropping it at another station and at the same time there will be a gun attached or glue gun attached and I could use those to gluing or processing on that particular panel or assembly. after it has been dropped on the fixture. We also have different types of stands, we have gun stands, pedestal stands, glue stands etc. which are very much required because when we are talking about the line so we have what happens like we have different variants like for each nowadays each car has different different variants it goes on like the base model, upper model, best model and everything, the top model and all.
So it will, the dimensions and everything remains but there will be a minimum of changes for that. There will be minimum changes in the grippers and the fixtures also ok. In fixture we can incorporate 2-3 items at same time but the welding processes can be different or some parts will not be there, some parts will be there. There will be some differences if we are talking about different variants. So in that case there might be some cases where different grippers are required like for one variant once gripper type of gripper is required for another variant another type of gripper is required.
But we cannot replace robot in that condition because robot is quite expensive quite well so replacing a robot is much active task. So what we do, we design two different grippers and we provide a gripper stand to that so what happens if there is variant A working on variant A so robot will go to the gripper A hold it and will do whatever the process is to be done. Now we have to go for variant B so gripper will go to that particular gripper stand of gripper A drop that gripper come to gripper B get attached to gripper B and start working on the variant B assembly on that fixture.
Now there are pedestal stand. Pedestal stands are basically fixed stand like we need stand to mount our robot. We cannot directly mount robot on the floor. We need some table like structure, stand like structure on which robot will be mounted. Then we will have gluing stand like there will be stand where a glue gun will be mounted and will be fixed so that a gripper will take the panel below that gun and the gluing will be done. Then docking stand, docking stand as I said for the creepers those are called docking stand. Also sometimes happen like if you are talking about the welding.
So for different welding we use different guns okay due to approachability and everything. So let's say if we are having a floor panel so it has weld at the center and at the edge also. So we might use different guns so at welding at the edge we will use different gun and to reach at the center we will use a longer gun. So for that also we will have the gun stand where a robot can interchange the gun as per the spot requirement. After that we have some miscellaneous stations that is squaring, buffer stand, racks, pallets, take-out rails, conveyors etc.
Clearing is nothing it's just what happens in some stations after gluing that glue needs to be settled down to be dried off. So it is a belt type structure where you put the panel or assembly and it will move and will reach to another station or another zone and in the meanwhile it will get cooler. Buffer stands as the name suggests it's a stand where you stock the buffer item like an assembly A is being welded at any station. Now it needs to be moved to some other zone or some other station.
So what we can do we can put in a buffer stand where 10 assemblies or 15 assemblies or 20 assemblies of that particular assembly are welded and can be capped in a way that it could not fall off or it cannot also it can be moved together and in a very easy way. So those are called buffer stand. Then we have racks pallet that goes with the same as buffer stand. Then we have take-out rollies at the end of one zone like when my underbody is being is has been done.
So there will be a take-out trolley at the end. What is the requirement of take-out trolley is like after a batch of few units like after every 50 units or 30 units or 20 units. There will be a quality inspection of that particular underbody of whole what like all the spots are there or not. All the assemblies are proper or not are all everything are in dimensions or not. Everything should be checked by the operator visual QC or CMM QC whatever the means can be. He take out a particular unit from a batch and he checks that.
So if anything comes out like if one spot has been missed it can be rectified. It can be seen through that and so that we will not lose 100 units of bodies into rejection. We can stop that at a number of 10 or 20 or 30 and that can be rectified easily rather than rectifying 100 units. So for that we use take-out rallies and then the conveyors. Convayors are basically used where we move tend to move a certain assembly or certain parts from one place to another or one zone to another in an automated way where there won't be involvement of any manual operator.
So an assembly when done it's to be kept on a conveyor and it will have N number of pallets. So the conveyor sizes can be of 1 meter, 2 meter, 3 meter, 6 meter, 20, 25 meters based on the requirement. So once the assembly is done that is to be taken out from that fixture and kept on the conveyor. Now let's say conveyor is 10 meter long. So taking a particular body and moving going to that 10 meter range then dropping it off it will take larger time and larger efforts.
So in order to avoid that we use conveyor. So conveyor is automatically moving. So once the panel is been kept there it will move and second pallet will come, particular assembly will be kept on that and it will start moving again in such ways. Now to discuss in brief about BIW stations. So what is a tool? A tool is a fixture which consists of number of units together to hold a car part in general as we have already discussed. So geo tool is a fixture in which as I said earlier where the panels are welded together and their profile is maintained very accurately.
The geo metric of that assembly is formed in geo tool. The pin tolerance for geo pin will be of closer tolerance that is 0.15 in general. I will show some geo tool. Also some geo tool.