Lesson finished
Up next: BIW Fixture Project Lifecycle, Cycle Time Study and Joining Methods
Unlock all 41 lessons of Automotive BIW Fixture Design using CATIA V5Full course ₹40,000 · paid
Geo and Re-Spot Pin Tolerances, Clamps, Grippers and Terminology
A free lesson from Skill-Lync's Automotive BIW Fixture Design using CATIA V5 course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Basic Fixture and Clamping Systems”
What will you learn in this free Automotive BIW Fixture Design using CATIA V5 lesson?
The instructor shows example geo fixtures with swivel and power clamp cylinders and explains pin tolerances, for instance a 19.85 mm pin for a 20 mm hole. The lesson also covers checking fixture types, gripper and stand types, and fixture terms such as PLP, risers, shims, units, sensors and reed switches.
- Swivel versus power clamp cylinders and opening angles
- Undersized pin tolerances for geo and re-spot tools
- Gripper types and stand types in BIW lines
- PLP, riser, shim, sensor and reed switch terms
What comes after lesson 2?
The next free lesson is lesson 3, “BIW Fixture Project Lifecycle, Cycle Time Study and Joining Methods” (30 min). Later in Skill-Lync's Automotive BIW Fixture Design using CATIA V5 course (paid): lesson 4, Understanding Different Welding Processes; lesson 5, B Fixture Design; lesson 6, Week 3: Design Methodologies - Session 2. The full course has 41 lessons (16 h 52 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
So this is an example of a geofixture. And in this fixture, floor assembly is being welded. So if you could see, like we have different parts that are being assembled together. This is one part, one assembly. Okay. These points are actually the spot marks where the spotting will be done. Okay. See. So these are, this is one, this is one assembly. Sorry, one part of the assembly. This is another part of the assembly. This is main part, main floor. This is one part. Then this is one part of the assembly. This is one part of the assembly. Same goes this and this. So if you could see, we have like 1, 2, 3, 4, 5, 6, 7, 8, somewhere 9 to 10 parts that are being welded together in this fixture.
Now, like different OEMS or different suppliers, they have different set of standards for designing their fixture. Like for this one, we are using a cylinder of this sort. This is called swivel type clamping. And in India, most OEMS use such clamping system. So this is called swivel type clamping system. Talk about another fixture. So this is another geofixture. Now here you could see the clamping cylinders and clamping mechanism is quite different. As these cylinders are called power clamped cylinders. And these are basically used in European OEMS. In India, not all the OEMS use or prefer such clamping system as of now.
So basic difference in these two are, I will be explaining this when we will start designing about the fixtures and the units. Just to brief about you these things. The basic fixture is that like in this system, we are talking about this clamping system. This is the pivot point. This whole system, whole clamping system will rotate about this particular axis. So this is the pivot system. So we can actually change the pivot system as per our requirement because on the pivot, I'll explain this also. On the pivot, the opening and closing of the clamping will be done.
That needs to be checked. So in this, the pivot and this is a stroke base cylinder. It will work on the stroke. So it will go up to 100. It will open up 100. And we'll have to check while it is closing up 100 mm. So this should be properly open about this axis. So that my panel could come out. Now if you're talking about the power clamp cylinders, this is quite easy. It has a variation of 15 degree. Like if you have seen this one. So this is the closed condition. This is the open condition of the clamp pump. Right.
So if you're talking about this, it means it has a variation of frequency of or indexing of 15 degree. So this is 0. From 0, it can go up to 90 or 135 degree. It depends on different cylinder, different spacing of the clamp. Like if I'll say, let's say if you have to move this one. Okay. This is my clamp pump. Okay. I will select the axis. Okay. Now we have to check the opening. So we'll have to rotate through axis W and W axis will provide 15 degree and we'll rotate.
So in this direction. So in this direction. So this is 1, this is 2, 3 means 45 degree, 60 degree, 75 degree, 90. This is 90 degree position. Then 105 degree, 120 degree and 135 degree. This is the last position. So this cylinder. So we can actually control this rotation manually. So they have this some screwing system through which we can control like up to what angle it should go. Should it go up till 135 degree or should it stop at 30 degree or should it stop at 60 degree.
We are detailing this particular unit. So we have to define this how much opening is required accordingly. While doing the assembly of this, the operator will adjust the setting up to 90 degree or 60 degree or whatever the requirement is. So this is a basic fixture unit. Now we have a pin unit. Okay. This is a pin unit. So we have a pin here. This is a riser. We will be getting to know about different units, different parts of units much in a much, much broader way. Just for the way you to, for your understanding to get through the terms and the terminologies, understandings.
So just keep those, you know, we will be explaining in the next sessions. So this is our, uh, fixes, geo spot fixes. Now there was one point like geo pin will be of closer tolerance. That is minus 0.15 in general. What implies it? Let's say if we are talking about this car panel, now it will have this, this will hold, this pins will go into holes of this car. I mean, like this hole is there. Okay. Now in 3D or, or in 2D, you will see because it is designer.
We don't, uh, get manufacturing defects in designing. So here it will show like the dimension being X or let's say 20 mm. The dimension is 20 mm of this hole. So theoretically we should design a pin, which will be of size of 30 mm. Or we should manufacture a pin, which will be a size of 30 mm or 20 mm, whatever will be the size of that hole. But we do not practice that. Like in designing, we'll go with the same dimension as the size of the hole.
Like if it is 20, we'll go with 20. If it is 30, we'll go with 30. When we are going to manufacture that particular pin, we will have to consider some manufacturing defects. What happened? These holes, they are cut out from dies and stampings and all. So when you cut it, it will leave some edges and rough marks and rough patterns on the edges. Like if you're talking about a paper, if you know, you hold a paper, you'll put a finger or any pin or pencil or pen.
You will see there'll be, it will create a hole, but there will be some extra or irregular surfaces around the edge of that hole. That won't be a lot, but it will be enough to consider into tolerance. So that is why whenever we manufacture pins for sheet metal holes, even for geometric positioning and geometric fixtures, we try to get that pin undersized from that particular hole. So if we're talking about a geofixer is very precise fixture because the geometric should be very accurate as per design and as per the relative dimensions.
So it means that we need to be very precise with geofixer. So tolerance level in all terms should be very less in geofixer and also in checking fixture. So now we are talking about the geofixer. Pin should be undersized. So as mentioned here, as you could see, the build tolerance for a geofixer will be closer tolerance that is minus 0.15 in general. Consider panel hole size 20 mm. The pin diameter should be 19.85 mm. It means that if the hole size of the panel is 20 mm and when we are manufacturing that pin, the pin diameter should be somewhere around 19.85 mm.
But we don't show 19.85 mm while designing. While we are designing the pin, we will have to go with 20 mm. Now when we will detail it because 0.15 is a tolerance. This is not the dimension of that pin. Okay. This is basic tolerance. So while detailing, we'll mention the diameter as 20 and with tolerance level of 0 to minus 0.15. This was the geo station. Now if we're talking about the re-spot stations. So re-spot tool is a fixture in which the remaining weld spots which are not achieved in geo tool are welded for the pre-welded panel from the geo tool. As I have already explained, a re-spot tools are those tools where the missed out that the spots or the weld points that have, we have not considered for geo stations or geo tools are to be welded here, are to be joined here to incorporate the loss of idle time of the stations or increase the cycle time of stations.
Okay. Now here you could see the pin tolerance for a re-spot pin will be of tolerance of minus 0.28 in general. It is less precise as compared to geo-fixer. The reason being it is not forming the geometry of that assembly. It is just re-spotting the remaining spots so that that assembly could get the particular strength and stiffness and rigidity. It does not have to do anything with defining the geometry of that assembly. So like considering a hole size of 20 mm, the pin diameter will be around 19.72.
Now marriage or hemming tool, as I have already explained, marriage tool is a station or tool where side bodies or under bodies and front bodies are to be welded or framed together. And that can go for framer tool where the roof will come and that will be joined together. Now at hemming station, what hemming is a process, there is not very much required like in all assemblies of a car panel. There are some specific assemblies like the hood assembly. The door panel assemblies. Now, if you're talking about the hood or the door panel, so there are two sections, okay. One interior section, one exterior or outer section. So what happens? On the edges of the outer section, it will envelop the interior section. If you could see a car or something, you could see on the door edges that there will be overlapping of the side edges of outer surface of the car door onto the inner surface.
So that bending off is called as a hemming process. We'll see a pictorial representation in when we'll be discussing in our next session about the joining processes of BIW welding parts. Now, moving on to the checking station. So our checking station tool is a fixture which is used to check the automotive parts or assemblies. Ensuring all the coordinates, relative dimensions and position as per the tolerances. For this, a checking station can be a gauge type, fixed type and automated gauge checking fixtures. As I've told earlier also, the checking stations or checking fixtures or checking tools are those where you check the dimensions, you check the coordinates, you check the relative dimensions and the quality of that particular assembly, whether it is okay or not.
And with different types of gauges, the different gauges, the different gauges, the infixer gauges or some external gauges, whether the dimensions are as per the dimensions and the tolerances that are provided by the design team or the design of that particular assembly. So it can be of different types. It can be of gauge type, a fixed type or automatic checking fixtures. A gauge type is just checking gauge tool where work pieces hold and various measuring gauges are. So it is like work pieces hold. Like gauges are those sort of. For example, there is an assembly A. If we're talking about, let's say about the floor panel that we have just considered.
Okay, like this. So let's say it is a checking fixture. It won't have that much of clamping and everything. So what will happen? I'll just fix this whole assembly with these two pin position and I will give some clamp. Now, what I have to check whether all these assemblies, the remaining small parts, child parts are relative to each other or not or to this because this should be maintained properly. So here I will give a fix pin. Here for these checking this profiles or these holes will provide with some gauges. So the operator will fix clamp and now it will say if the gauge is properly inserting those holes, it means my assembly is properly done.
If it is not, so he will check in which direction it has moved. So he will correct that issue in the geo fixture and again he will produce one part, manufacture one part and again it will check. Once it is done, it is approved. It means the fixture is okay now and the quality of the assembly is being maintained. So there is a gauge type where the work piece is being hold and you do checking through gauge system. Second is a fixed type checking fixture where the work piece is fixed with clamps and pins and a CMM machine is used which measures the coordinates of the different points of the assembly or panel and compares it with the nominal values and gives a report.
First of all, what is a CMM? CMM is a coordinate measuring machine. It is a machine, very precise machine. With the help of CAT data, it checks different coordinates on the real time zone. So like if I am having a fixture or if I am having a panel, so car assembly. So I will have a CAT data of that particular car assembly. Now if I have to, let's say, check positions like whether this assembly is in accordance or in relative with these holes or not or this hole or not.
So what I will do and check with my 3D coordinate and I will give this coordinate some X, Y, Z coordinate as per the design. Now I will go on and check this coordinate. So CMM machine basically has a pointed ball type tip. Okay. On that tip, when we will touch, it will form a surface. It can form a surface. If we are taking three points in circular format, three or four points like this point, this point, this point and now this point. So it will detect, okay, it is a circle. Now four points of the circle has a center. This is a center and it will give coordinates of that center. That center you can compare with the one that is given in the design in the CAT model.
If any deviation is there, it will be generated in the report. Like it will go like if we are talking about this. So this is our Y axis. Okay. So if it says it is plus 0.2 mm in Y axis, it should like the coordinate in Y should be 100. Now it comes 100.2. It means it is 0.2 mm on the positive side of Y. So we need to take it on this side. So there is an issue in the assembly in the fixture. So a fixture, because the geofixer has done the assembly of this assembly, right?
So it means this part is locating at wrong position, the geofixer. So we will go back to the geofixer. We will rectify it. We will do the same of that fixture. We will rectify it. Okay. Now it should give that assembly at not 0.2 but at that 100 coordinate only of 5. So that will be a fixed type. Now automatic checking fixture is a fixture where automatic settings are being done through sensors and PLCs and switches and everything, lights and rays. When there, a part will be missing, it will attack and give us the signal that part, particular part is missing. When a profile, when a part is moved to some different positions, when the hole is mismatching and anything, anything is being done that can be rectified through lasering system or various means through automated system.
Mostly use our fixed type checking fixture and checking gauges. Automated checking fixture are considered to be very costly. That is why. And we avoid going for automated. Because it does not make very huge difference between checking fixture or fixed type checking fixture automated system. A gripper is a device or fixture which holds the car panel and is fixed to the manipulating end of a robot or an end effector. So gripper is basically a fixture but with lesser part, with lesser weight. Okay. Okay. So we always tend to keep our gripper as lower weight as possible because it has to be mounted on the arm of a robot or some end effector, some servo system.
Okay. So the weight needs to be kept very low. Okay. So that is why we use frame instead of plates as we do in the case of fixtures. We use individual plates, localized plates and frames and etc. We try to keep it as sturdy as possible and as light as possible. So there can be different types of grippers. Like one is material handling gripper. So material handling gripper are designed for handling the car panel from one tool to another tool. As I told earlier also, the basic motive of the material handling tool is it will pick the car panel from one station and it will drop car panel to another station.
Now process gripper. Process gripper designed for handling the car panel from one station to another station and in addition to that, it undergoes process like pedestal welding, pedestal riveting, gluing. Okay. In process gripper, what happens? A gripper will pick a panel or an assembly from station A. It will go to some pedestal stands, pedestal welding stand, pedestal gluing stand or riveting stand. So there will be a pedestal fixed stand where a gun will be mounted, a gluing gun or riveting gun or spotting gun and the gripper will take that assembly or that panel below those guns will orient in specified directions or positions of the spot.
And the spotting or gluing will be done on that particular assembly and then it will drop to station B for further processes. So this is called a process gripper. So a gripper is doing some process. It is also welding or gluing that particular assembly before unloading it to some other station. Combo gripper is a gripper designed for handling the car panel from one tool to another tool also with a combination of welding at the other side of the gripper or for welding. So a combo gripper is a gripper where it will be picking a car panel from one station to another station and also it is incorporating a gun.
So once it has picked and dropped, it will rotate and start spotting or welding and gluing whatever the process needs to be done. That is a combo gripper, dual gripper. Dual gripper are designed for handling the car panel from one tool to another tool with two-sided gripper. So it is actually designed for handling the car panel from one station to another station with two-sided grippers. Means it can hold two panels simultaneously. So it is going to station 1, station A, pick a panel. It generally happens where like we are talking about the side bodies like where the symmetry of cars are there.
We will need a set of bodies together to be assembled at some places, majorly at those places. So gripper will go to station LH side. It will pick the LH side of a part. It will go to the RH side. It will pick the RS and then it will go to the sender mainline assembly and will drop to the fixture and the assembly will be done. Now different types of stands are there. First, the gluing is a sealer stand. Gluing gun or sealer gun is fixed to a welded or a standard stand which is grouted to the floor permanently.
So if you could see, this is a gluing stand. So it is a welded or standard stand that is fixed to the floor permanently. Fixing to the floor is very much required because it, due to vibrations or in the plants or other factors, it should not move. So this stand should not move in any direction because even it moves 1 mm, 2 mm over a period and let's say after an year or 2 years, this stand tend to move due to vibrations. Every day it was moving 0.1 mm, 0.1 mm, 0.1 mm, which is very slow.
And after an year, it came to notice that it moved around 2 to 3 mm. So now if my gluing has to start with coordinate at x is equal to 100, now this has moved at 2 mm, so my gluing will start at x is equal to 102 or 98, right? So this is one gluing and sealer stand. So that is why it needs to be fixed permanently through the ground. So what happens? It will be connected to some in-fit gluing system. This nozzle, the gluing will come when the robot with gripper.
We'll bring the panel below here and prescribe orientation and position with the presence of some sensors and or some programs. This will get activated and start releasing the glue and the gripper will move. So ensuring that in that profile at which the gluing is to be done. Now the docking stand. When robots are selected from multitasking like material handling and welding, which cannot carry port due to some limitations, payload capacity of the robot or space constant, the robot will drop and pick the gripper or gun after completing the respective operation with the help of a docking stand.
So docking stands are basically for guns and grippers as I've said, like robot also has some limitations, okay. They have a prescribed load capacity for their arm. So let's say a robot has a load capacity of 20 kg. Now I have designed a gripper that is weighing around 14 kg or 16 kg and my gun is weighing around 17 kg. So it is beyond the capacity of robot. Also if there are some space constraints in my gripper, I cannot mount a gripper and a gun together.
So what we do, we use that robot for multitasking because robot costs a lot more than those things. So we will not use another robot because robot will again require a lot of space, a lot of cost and a lot of maintenance and everything. So we avoid using another robot instead of that. We will use a stand. Now my robot will do multitasking. Once it will go attached with the gripper, it will go take a panel, drop it here, then we will lose the gripper to one docking stand.
Okay, like it will go live here. It will be clamped and attached. It will leave the gripper. Now here the gun will be mounted. It will come here, attach the gun, take the gun, do the welding, then drop the gun, then again take the gripper and so on. Date stamp stand, the panel will get the date embossed on it with the date stamping device mounted on it. Date stamp is basically a stamp stand where the batch number or the date of that manufacturing is to be embarked on that panel.
So it will have some system on that stand. People will take that assembly below that, a date will be embossed on that panel. Buffer storage, these are the examples of buffer storage. As you could see, these are very similar, so it has provided sections, so N number of assemblies can be kept here in between, like 10, 20, 30, 5, 6, whatever requirement, whatever number of assemblies are required. So you could see, this is one assembly, this is two assemblies, this is three assemblies. So this is buffer together.
So now it can be moved together or stored for inventory purpose. Like we have to do maintenance of particular station, but I don't want my whole production line to be stopped. So what I'll do, I'll start production of that particular station and I'll keep some items at buffer so that my other lines are not affected and my continuous production is in process. Now these are conveyor tools. As I told, conveys can be a belt type conveyor or chain drive conveyors, okay. So it will actually have a palette or fixer type structure where the panel will be kept and it will move.
So this will go from here to the end and again from bottom it will rotate from this axis, okay. So this is conveyor tools. Now particular guns and particular guns like the fixed guns like this one and this one, the guns will be fixed. The gripper with robot arm will take the assembly from one fixture and will take to this particular gun and orient in particular orientation and position and the spotting or welding will be done. Takeout role as I have already explained, it is used to check the inspection of that particular assembly.
Takeout role is used to take the car panel out of the robotic working cell between the cycle for inspection purpose. So it is done between the cycle itself, not every time at a batch of like 10, 20 or 30 items. Now there are basic terminologies. There will be much more basic terminologies, but as of now you should understand these basic terminologies, okay. NC milers or fingers, I will explain through the fixtures also. So NC milers or fixtures, these are nothing but the part which are holding the panel like this part.
This is an NC, different countries at different centers. In India and majorly, majorly, globally we call it as milers. So miler is which is like holding a panel from top and bottom. So you will see from bottom also it will have a resting and from top it is a little clamping. So this is a clamping miler, this is a resting miler. Every clamping miler will have a resting miler that is very much important, okay. So it is a jaw type, it is actually holding this panel so that if welding is done, it won't deform from its position.
So these are the milers or fingers. Our second point is PLP. This is a principal locating point. So principal locating points are those where we use pins for locating these panels, okay. So this will be mentioned in the 3D or the 2D or the assembly or the part like which hole, like there are n number of holes. There are three holes, this one, three holes, this one. So there will be a confusion like which hole need to be used for placing because all holes are not accurate or not precise when coming out of stamping, okay.
So at the start of designing only, BIW designing is also done taking the fact that it should be able to manufacture. It should be easy for tool makers, for tool designers to consider the points to make a better tool that can produce quality assembly of panels repeatedly over a period of time, right. So they mention in their drawings like which hole needs to be taken carefully and precisely. Whose dimensions, relative positional dimensions or dimensions need to be very much precise even if in stamping or in fixtures.
So those are called PLPs, principal locating points. Now blade. Blade are these plates which are attached to riser. These are called risers. Risers can be of L type. A welded square to frame type, this one, okay. Like this one. Risers is basically a manufacturing part that gives and height or rise to all assemblies, okay. So this is called risers. And on risers will be mounting a plate to which cylinder will be mounted and other items can be mounted easily. These are called blade. Now in fixture, see we are providing tolerance to each and every part.
To each miler, to each hole. We give tolerance to each and everything. So those all tolerances tend to stack up, right. Like we give plus minus 0.1, plus minus 0.2, plus minus 0.1, plus minus 0.2. So if you're talking about an assembly, okay. Like this part has a tolerance of plus minus 0.2. It's on the plus side of 0.2. It is okay as per quality and tolerance. Now this part also has a tolerance of plus minus 0.2. It also is plus on the minus 0.2 side.
So now stack up tolerance is 0.4 mm. So those will, those stacked up tolerances will add up together and reflect at the end point. Like the clamping. So this is the position. If it goes below this and above this, it won't hold this panel proper. Like this is the accurate position of this miler. Now, after stacking up the tolerance, this tends to be a bit on the downside. So it means this will go 0.5 mm, 0.6 mm on the lower side, which will dent the panel, which will mark an impression on the panel due to high force, which will damage the panel, which we don't want.
Or there will be chances that this part is on the upper side due to tolerance and everything. So this will also go up 0.2 mm point. So there will be a gap between this and this. So there will be no holding. So when the welding will be done, there will be distortions. So in order to avoid that, we use shims. So we can easily adjust after assembly. So whatever the stack up of tolerances will be there, we can rectify through the tolerances. These shims come in thickness of 0.5 mm, 1 mm, 0.2 mm.
So we can take it out and put it in and check with the CMM whether I am getting the desired position or dimension or not. So these are called shims. I'll explain the basics and theory of shims while designing the units. Rough locators. Okay, great. Rough locators are those which are used majorly in manual fixture. These are the manual fixtures. So rough locators are used to guide like an operator is putting an assembly in a fixture. So he should not mistakenly or intentionally put that panel or assembly in wrong or retention.
Like so we provide as guides like this one on the edges. One, this one is there. And one, this one is there. One, this one is there. Okay. One, this one is there. So this acts as a guide. So operator will get an idea. Okay. I have to keep my assembly or part between these rough locators. So this will help in guiding. So these are called rough locators. Hardwares. Hardwares are basic like bolts, fasteners, nuts and everything. Those are the hardwares. CMM as I told that is called coordinate machine that I use to check the coordinates of a fixture or of an assembly as per the CAD data that has been designed.
Units. A fixture is an assembly of different units. So this hole is one unit. I will explain if I am talking about units. So this is one unit. This is base unit. This is another unit. This is a pin unit. Right. This is a pin unit. Again, this is another pin unit. It is a clamp unit. So these are different units. As I said earlier, it is an assembly of different types of units assembled together to form a fixture. So this is another unit. Now this is one another unit.
So these are, there are different, different units. These are called units. Number plate. Okay. I don't have a number plate on this. Number plate is basically an aluminum embossing that is pasted on each unit to recognize that unit number. Okay. Like this one. Okay. So one, a person cannot easily remember like which unit number is this and like there will be some issues. So he can not easily remember. So if you know the number embarked on this, so we can check in the 3D. Okay. The unit number six or unit number 10 has this issue. So what is that is, what is in design, whether design is wrong or design is okay. Manufacturing that can be easily rectified. That is why we provide numbers and those are called number plates.
Coordinate plates. Now, when we discuss about this fixtures, I'll tell you on every fixture, we have a tooling hole through which, which is also called a master hole through which all fixtures are to be checked through CMM. Mastering that particular hole and cover that hole so that it won't get other impurities and hole does not get any wear and tear or distorted. We use coordinates hole. So on that particular hole, the coordinate of that hole will be mentioned. I'll explain this when we'll be working on this base units. Name plate. This is a name plate. Okay. So name plate is just a marking where the basic information will be mentioned. The fixture type, the weight, the panel name, panel number, company name, etc, etc.
Clamp arm. Now in clamp unit, this is a clamp unit. So the arm which moves, okay, the assembly that move is called clamp arm, right? Like this one is a clamp arm. This, this one is again, this will move this alone. I'll show you. Okay. Only this part is a clamp arm. So on the clamp arm, other assemblies will be done on the clamp miler. This is a complex one. When we'll start designing, we'll start with the easy clamping systems. So this is the clamp arm. In this type of fixture, now if we're talking about the power clamp cylinders, so this part, which I was rototing, this part is the clamp arm.
Okay, on which clamp milers and everything will be mounted. Pivot, I've already explained. This is the pivot. Through about the axis, the clamp arm will move. Class A surface or skin surface? Okay. Now in BIW or fixer, we have a class A surface or a skin surface that implies to that area of BIW or that car body, which is visible to the end customer or visible to everyone, like the outer shell of the body, like the outer side of the car or the hood. Which is visible to us now. And that needs to be aesthetically very good. There is no dent to be accepted, no scratches to be accepted. So those are called A surface or skin surface.
So if you're designing a fixture for skin surface or A class surface, we need to make sure that the clamping or resting materials should be soft because the thickness of A class surface or skin surface is quite less. And also it should not attend, it should not have any mark on the panel, even a smallest one. So that is why we use soft materials such as nylons and pew items so that it could exert sufficient force but cannot be able to embark any impression on that part.
Read switches and sensors. Okay. Read switches and sensors are basically electrical parts. You need just to have an understanding. See, sensors are those which give you the detection whether my part is available or not. Like in this. I don't think we have a fixture. So sensors and read switches are used only in that situation where there is automatic fixture. Okay. So fixtures can be automatic that are run through automated system through PLCs and control panels or just a pneumatic system where operator is working on it and it has pneumatic buttons.
Is pressing that buttons of clamp opening and closing and everything but no automated things are being done. So this is a pneumatic manual fixture. There is no automated thing available in the fixture. No sensors, no read switches. So everything is done manually by the operator. Now if you are talking about this fixture. Now if you are talking about this fixture. I will just remove the panel. I will just show you the fixture. See, this is a sensor. So what it is doing? It is confirming that my main panel is available.
So if we are having a nine panel, right? If like this is an assembly of nine parts. So it means there should be at least minimum nine to ten sensors available. If the part is big like the main part, it means it should have two sensors available to detect the positioning of that part to ensuring that that part is available because sometime happens operator forgets to put one part. So if it does not put the part who will ensure that and that if that part has not been taken care of, not been checked, it means it wrong part rejected part will go for further assembly. And then the problem will arise. And at that later stage, it will be much more cost effective and time consuming. So that is why to make sure we have provided sensors at every station. So we will check at every station like this is one sensor. Okay. Wherever new parts are there, there is no, this is one sensor.
So this is checking this part. So this is checking this part. For this also, we will have another, we'll have a set of sensor. This, this is a sensor for this part. Likewise. So this is the main use of sensor. Now, these are the read switches. Okay. Read switches are magnetic read sensors, you could say, that are mounted on the cylinder. Now, cylinder has a piston type structure right inside it. So let's say piston is here. When air is moved into it, this piston will go up and it will, this rod will go up and clamping will be done. Now, when air is moved in this nozzle, piston will go down and this will come out and clamp will open. Right.
What rates is done? It confirms the position of the piston. Now, when piston is here, it means your rod is downward. It means your whole assembly is open. It means your panel is ready to take out. Okay. Or if your piston is this way, this will blink. This will give signal to your control panel. It means the rod is up. It means all assembly is being properly tucked in. All clamping is proper in position. It means welding can be proceeded. So for other process to move on, for confirmation, we need read switches. That is to be, that is mounted on that particular cylinder or different cylinders to ensure that everything is working. If even any read switch or any sensor has stopped working or has not detected anything, it means there is some issues.
So the line will stop automatically at that stage and will not proceed for the second process and will start initiate the things again from the initial. We'll have to check that what is the issue and why the sensor is not there, but the part is missing, whether we have an issue with the sensor or cylinder has not clamped properly. This avoids accidents and rejections of assemblies, mistakes and everything. So it is very much important to have sensors and resources in your system. Okay. Thank you. That's all for this session. For introduction. For next session, we'll start with BIW fixture basics. We'll, we'll understand more basics about BIW fixture, designing of BIW fixture with 3 to 1 principle and different units that are, that I've already explained, that will be explained in brief for designs and everything. Thank you.