Geneva mechanism calculator

Design an internal or external Geneva drive: the centre distance that lets the pin enter without a jolt, how long the wheel moves and dwells, its angle, speed and acceleration through each step, and the contact force between pin and slot. Free, no sign-up, runs in your browser.

It opens on the internal Geneva from Skill-Lync's SOLIDWORKS Motion project (4 slots, pin at 160 mm, 10 and 20 rpm). The third tab checks a motion study report and names the slips Skill-Lync found when it read 309 of them.

Kinematics from the pin geometry · checked by finite differences in Python · SOLIDWORKS Motion help · Updated 20 Nov 2026

Defaults: the project's internal Geneva (4 slots, pin Ø40 mm at r = 160 mm, driver disc Ø420 mm) at 10 rpm. The centre distance is computed for a shock-free entry.

Centre distance226.274 mmfor a shock-free entry
Moves / dwells270° / 90°4.5 s / 1.5 s per turn
Peak ω₂ / α₂24.85 deg/sα₂ 1.097 rad/s² at entry
54°
0100driven wheel angle θ₂ (deg)01020angular velocity ω₂ (deg/s)-101angular acceleration α₂ (rad/s²)024681012time (s); vertical lines: pin enters / leaves a slot
  • Centre distance for a shock-free entry: a = r / sin(180°/4) = 226.274 mm. The pin then enters along the slot, so the wheel starts from rest with no velocity jump.
  • Internal: the wheel moves for 270° of crank rotation (4.5 s at 10 rpm) and dwells for 90° (1.5 s). It turns the same way as the crank.
  • Peak wheel speed 0.4142 × ω₁ = 24.85 deg/s, when the pin is farthest from the wheel centre.
  • Peak acceleration 1 × ω₁² = 1.097 rad/s², right at the pin's entry and exit: the acceleration jumps from 0 to its maximum in one instant (infinite jerk), so that is where the contact force spikes.
  • Slot travel: the pin centre runs from 160 to 386.3 mm from the wheel centre, 226.3 mm; the slot must reach at least 406.3 mm from the centre, and the central cut-out must clear 86.27 mm so the pin passes during the dwell.

What does the internal Geneva project ask?

Model the driver and driven wheels of an internal Geneva mechanism in SOLIDWORKS, assemble them, run a motion study with the driver at 10 rpm (60 frames per second) and then 20 rpm (120 frames per second), and plot the contact force between the wheels and the driven wheel's angular displacement, with and without Precise contact. The driver is a Ø420 mm disc with a Ø40 mm pin at 160 mm from its centre. The driven wheel is Ø1120 mm with four Ø40 mm-wide radial slots running out to r = 520 mm from a Ø240 mm central cut-out. The assembly position comes from a Ø320 mm circle (the pin's path) drawn tangent to the axes of two neighbouring slots.

It is the first project of Skill-Lync's Multibody Dynamics using SolidWorks course. Skill-Lync has 310 public reports with "Geneva" in the title, 293 of them for the internal wheel; the findings below come from reading all of them.

The centre distance: why 226.27 mm

The pin should enter the slot moving along it. Then the wheel, at rest during the dwell, starts turning from zero speed instead of being struck sideways. That happens when the crank is at right angles to the slot at the moment of entry, so the crank radius, the centre distance and the half-angle between slots form a right triangle:

The Ø320 mm circle tangent to two slot axes is exactly this construction. Of the 25 reports that state their centre distance, 13 use 226.27 mm, 3 are within 0.13 mm, and 8 use something else. What the off values do (r = 160 mm, 4 slots):

Centre distancePin path vs slot axisWhat happens at entry
226.27 mmtouches it (tangent)wheel starts from rest, no velocity jump
224.50 mm (2 reports)cuts it at 7.2°wheel must jump to 8.6 deg/s at 10 rpm: an impact
224.85 mmcuts it at 6.4°jump to 7.6 deg/s
222.71 mmcuts it at 10.2°jump to 13.1 deg/s
226.72 mmmisses it by 0.32 mmpin hits the slot edge
234.09 mm (2 reports)misses it by 5.5 mmpin hits the slot edge and drags the wheel
234.54 mmmisses it by 5.8 mmsame

One report arrived at 224.50 mm "after analyzing various distance measurements" because it made the assembly move "without any unwanted collisions". With the pin exactly as wide as the slot there is no slack, so every distance except the tangential one turns each entry into a collision. The calculated force then depends on the contact settings, not on the mechanism. A few tenths of a millimetre of clearance in the slot is what a real drive would have.

Motion and dwell: internal vs external

The wheel moves while the pin is in a slot. Between entry and exit the crank turns through

so a 4-slot internal Geneva moves for 270° of each crank turn and dwells for 90°, the opposite of the external one. 5 reports copy the sentence "after the pin leaves the slot, the driver will rotate through 270° while the follower dwells". That sentence describes the external four-slot wheel, and 4 more say an internal Geneva dwells for more than 180°. For the same crank radius:

SlotsInternal: moves / dwellsExternal: moves / dwellsPeak ω₂/ω₁ int. / ext.Peak α₂/ω₁² int. / ext.
3300° / 60°60° / 300°0.46 / 6.461.73 / 31.39
4270° / 90°90° / 270°0.41 / 2.411.00 / 5.41
6240° / 120°120° / 240°0.33 / 1.000.58 / 1.35
8225° / 135°135° / 225°0.28 / 0.620.41 / 0.70

At the project's 10 rpm one crank turn takes 6 s: the wheel turns 90° in 4.5 s and rests for 1.5 s. One report reads 4 s of motion and 2 s of dwell off its plot; the mechanism gives 4.5 s and 1.5 s.

The wheel's angular velocity and acceleration

With φ the crank angle measured from the line of centres (φ = 0 when the pin is in line with both centres), the driven wheel's speed and acceleration are, with the upper signs for an internal Geneva and the lower for an external one,

At entry the speed is zero and the acceleration is the same for both types:

The difference is what happens next. In an internal Geneva the acceleration falls from that value straight away, so the entry is its maximum: 1.00 ω₁² for 4 slots, 1.10 rad/s² at 10 rpm. In an external one it keeps rising to 5.41 ω₁², 33.5° of crank after entry. Either way the acceleration jumps from zero at the entry instant (infinite jerk). That jump is why Geneva drives are noisy at speed and why the contact force spikes there.

How large should the contact force be?

With rigid parts and no friction, the pin pushes on the slot wall at right angles to the slot, at a distance ρ from the wheel centre. The only thing it has to overcome is the wheel's inertia (plus any load torque):

For the project's wheel, I₂ is 5.87 kg m² if no material is assigned (the part then takes the density in Document Properties > Material Properties, 1000 kg/m³ in the default templates; mass 35.0 kg), or 46.1 kg m² in steel (275 kg). The entry force is then 40.2 N at 10 rpm and 160.8 N at 20 rpm with no material, or 316 N and 1,263 N in steel. It is the largest force of the stroke, and four times larger at twice the speed. Picking "Steel (Dry)" in the Contact dialog only sets the properties of the touching faces during contact (SOLIDWORKS lists a static friction coefficient of 0.30 and a dynamic one of 0.25 for it); the wheel's mass still comes from the part, so assign steel to the part to model a steel wheel. SOLIDWORKS' own troubleshooting notes warn that a wrong density "can significantly affect the reaction forces".

The 20 reports that quote a peak contact force give anything from 92 N to 8,76,054 N. Those peaks are impacts: the solver's contact model (a stiffness and damping acting on a tiny overlap) resolving a collision between the pin and the slot wall within a few output frames. Their size changes with the frames per second, with Use Precise Contact (which computes contact from the equations of the solid bodies instead of many-sided polygons), with the stiffness and damping and with the centre distance. That is why 20 rpm gave anywhere from 1.02 to 4.0 times the 10 rpm peak in the reports that ran both speeds, instead of a clean 4. Compare the smooth part of your plot, away from the spikes, with the ideal curve in the second tab.

0100contact force (N): 10 rpm solid, 20 rpm dashed-202driver torque from the wheel's inertia (N m)050100150200250crank angle since the pin entered (deg)

Ideal contact force and the driver torque it needs for the project's wheel with no material assigned, 10 rpm (solid) and 20 rpm (dashed), over one 270° stroke. The force decreases as the pin moves outwards and the acceleration reverses; it is largest at entry and exit.

Which slips does the check tab catch?

  • A centre distance that is not r / sin(180°/n): how far the pin path misses or cuts the slot axis, and the speed the wheel would need at entry.
  • The external Geneva's dwell quoted for an internal one ("270° while the follower dwells").
  • Force that "rises linearly with rpm": inertia forces go with speed squared (11 reports say proportional).
  • A peak force far above the inertia force: an impact from the contact model, to be quoted with its settings.
  • Too few frames per second for the speed: 60 fps at 10 rpm is 1 output frame per degree of crank; keep that when the rpm changes. Frames set what the plots show; the solver's own step is the separate Maximum Integrator Step Size.

What this calculator does not cover

  • Impacts and clearance. The force is the rigid, frictionless, zero-clearance one. Real spikes depend on clearance, stiffness and damping, which a motion solver or a test has to give.
  • Locking surfaces. The wheel is assumed to stay put during the dwell. The project's driver disc has no locking arc, so in a simulation only friction and zero speed at exit hold it.
  • Curved-slot and modified Geneva drives, which reduce the entry jerk, and spherical Geneva wheels.
  • Wear and contact stress. The pin's Hertz stress against the slot wall needs the pin length and materials.
Learn multibody dynamics

Turning a mechanism into a motion study you can trust, with the right joints, contacts and solver settings, is the daily work of a design or MBD engineer. The Geneva mechanism is week 1 of Skill-Lync's Multibody Dynamics using SolidWorks course.

Frequently asked questions

How do you calculate the centre distance of a Geneva mechanism?

For the pin to enter the slot along the slot (so the wheel starts from rest with no jolt), the crank must be at right angles to the slot at entry, which gives r = a sin(180°/n). For 4 slots and a pin at r = 160 mm: a = 160 / sin 45° = 226.27 mm. The same rule holds for internal and external Geneva wheels.

What is the difference between an internal and an external Geneva mechanism?

In an external Geneva the crank sits outside the wheel and the wheel turns opposite to it; it moves during 180° − 360°/n of crank rotation (90° for 4 slots) and dwells for the rest. In an internal Geneva the crank sits inside the wheel and the wheel turns the same way; it moves during 180° + 360°/n (270° for 4 slots) and dwells for only 90°. The internal one is smoother: for 4 slots its peak acceleration is 5.4 times lower.

How long does a 4-slot internal Geneva dwell at 10 rpm?

One crank turn takes 6 s. The wheel moves for 270° of it (4.5 s) and dwells for 90° (1.5 s), turning 90° per crank turn. At 20 rpm it is 2.25 s and 0.75 s.

What is the maximum angular velocity of the Geneva wheel?

When the pin is in line with both centres: ω₂ = ω₁ λ/(1 + λ) for an internal Geneva and ω₁ λ/(1 − λ) for an external one, with λ = sin(180°/n). For 4 slots that is 0.414 ω₁ (internal) and 2.414 ω₁ (external): 24.9 deg/s and 144.9 deg/s at 10 rpm.

Why does the contact force spike in a SOLIDWORKS Motion study of a Geneva mechanism?

The wheel's acceleration jumps from zero to ω₁² tan(180°/n) the instant the pin enters, so the force jumps too. In a rigid, frictionless model of the course's internal Geneva that jump is only 40.2 N at 10 rpm with SOLIDWORKS' default template density. The spikes of thousands of newtons in the reports come from the impact the contact model computes when the pin meets the slot wall, which changes with the frame rate, Precise contact, the contact stiffness and the centre distance.

Does the contact force double when the speed doubles?

No. The inertia force is I α / ρ and α scales with ω₁², so doubling the speed multiplies it by 4: 40.2 N at 10 rpm becomes 160.8 N at 20 rpm for the course's wheel. 11 reports say the force is proportional to the speed; in the reports that ran both speeds the peak rose by anything from 1.02 to 4.0 times, which is the contact model, not the mechanism.

Related on Skill-Lync

Sources

  • F. H. Bickford, Mechanisms for Intermittent Motion (1972), ch. 9: for an internal Geneva "the motion period always exceeds the dwell period", the dwell is "always shorter than the time required for 180 degrees of input", and the reverse for an external one; Genevas give "no less than three, and usually no more than 18 dwells per revolution".
  • Engineers Edge, internal and external Geneva pages after Walsh, Handbook of Machining and Metal Working Calculations (2001): centre distance = r / sin(180°/n) for both types, ω₂ for the internal wheel, and the internal wheel's maximum acceleration "when roller enters slot", ω²/√(m² − 1) = ω² tan(180°/n).
  • Encyclopaedia Britannica, Geneva mechanism: the source of "After the pin leaves the slot, the driver will rotate through 270° while the follower dwells", written for the four-slot external wheel.
  • SOLIDWORKS Help: Contact PropertyManager (contact material applies "to touching faces during actual contact"), friction overview (Steel (Dry): static 0.30 at 0.1 mm/s, dynamic 0.25 at 10.16 mm/s), Motion Study Properties ("Use Precise Contact"; "Frames per second" = frames captured; Maximum Integrator Step Size), Motion study troubleshooting (density and reaction forces), Document Properties > Material Properties (density used when no material is applied). The 1000 kg/m³ template value is from Javelin's SOLIDWORKS notes.
  • Skill-Lync, 310 public Geneva mechanism reports, read 20 Nov 2026: centre distances, dwell statements, contact-force peaks and solver settings.
  • Skill-Lync, scripts/verify/geneva.py: redoes the kinematics from the pin vector with finite differences, the wheel's inertia by grid integration and the off-centre cases by bisection; the page re-checks every number against it when it is built.
Free counselling

From a motion study to a design career.

Building mechanisms in CAD, simulating them and explaining the numbers honestly is what design and multibody dynamics roles ask for. A Skill-Lync counsellor can tell you which SOLIDWORKS course fits where you are now.

Talk to a course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.