Week 9 - Project 1 - Door Trim Lower with Engineering Features

Aim : To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards.Draw the lines at the required angle and points for the European standard.Measure the distance at each angles and mention given model is pass or…

Hood Assembly using NX CAD: Objective: Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. Introduction: The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment…

We all are aware of the fact that the underbody of the previous models was made from durable metals such as steel, which is easily damaged and oxidized, forming rustWhile you are sitting on the driving seat enjoying the smooth ride, the underbody of your car is always exposed to muddy water, stones, rugged roads, and potholes.…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

AIM: To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in Tier-1 and OEM industries in Catia v5 SOFTWARE USED: CATIA V5 OBJECTIVES: Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained Ensured Proper…

MODEL 1: QUICK RETURN MECHANISM Step 1: Creating the Parts A) Slotted Bar: B) Bull Bush: C) Sliding Rod:- D) Connecting Rod: E) Rivet: Step 2: Assembled Part   MODEL 2: CV JOINT Step 1: Creating the Parts 1.Housing: 2. Clamp: 3.Joint: Step 2: Assembled Part:  

Aim : To create the " A Pillar" plastic component with B-Side fetures with the given Class A Surface and the master section curves as an input. The created plastic component is checked to meet the requirements of the draft angle and at the end perform the Draft analysis on the model. A) Creation of A Pillar Plastic Body…

AIM: The Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface is created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. A) Creation of the Plastic Component Step 1: Tooling Axis At first a point…

AIM:-       Create the Dog House for the Door Trim considering the design rules  Procedure: A: Creating a Plastic Component of the Door trim Step 1: Tooling Axis The Tooling Axis was created on the surface of the Class A Surface of the Door trim . A point was created on the surface along the Y-Axis…

  Aim: To create the rib for the Drill Handle considering the design rules in the door handle. Design Rules: Design Rules for Rib creation:   Create the Screw boss for the Drill Handle considering the design rules mentioned in the video. General Guidelines for Bosses: Draft - 0.5 degrees on the walls of boss…

AIM:-           Create the core and cavity blocks for the switch bezel in CATIA.   CONCEPT:- SWITCH BEZEL MIDDLE PART:- In previous challange switch bezel setp file is downloaded.so it is class A surface.Then i do draft analysis for class A surface.     After that i offset class…

NOTE:- THE GIVEN SWITCH BEZEL STEP FILE IS CHECK THE DRAFT ANALYSIS. IT SHOWS CENTER WALL AS RED IN COLOUR.SO MY FINAL OUTCOME PART DRAFT ANALYSIS SHOWS AS SAME AS FIRST ANALYSIS....  

AIM: A program in matlab to simulate the forward kinematics  of a 2R robotic arm CONCEPT: A robot arm is a known as, manipulator. in 2D arm structure it has two links and 2 joints , one is fixed on the base and the other one is moveable In basic , a robot arm consists of the parts: joints,links,and a end manupulator…

AIM:  A program in matlab to  function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file.    CONCEPT: File parsing is a process of talking input data and breaking it down to appropriate compants and using this data.for…

AIM: A program in matlab to simulate the to understand the concept of genetic algorithm by referring to varius sources.   CONCEPT: Genetic Algorithm (GA) is a search-based optimization technique based on the principles of Genetics and Natural Selection. It is frequently used to find optimal or near-optimal…

 %Solving 2nd order ODE using matlab clear all close all clc %Inputs %Damping coefficient b = 0.5; %Gravity g = 9.81; % length of rope l =1; % mass of ball m = 1; % initial condition % angular displacement =0; % angular velocity =5; theta_0 = [0;5]; % Time points % Generation 200 values between 0-20(sec) using linspace…