Week 9 - Attachment Feature Creation - Challenge 2

                                                 SWITCH BEZEL CORE & CAVITY DESIGN Objective:   Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.…

 AIM Prepare a report explaining the different fender design and its different mounts, manufacturing process and its design parameter.   FENDER Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). In other word…

FENDER WHEEL ARCH  Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The main role of wheel arch is it protects both passenger’s compartment and pedestrians from the projection of water, mud and stones. The wheel arch area is usually designed as a cover or shield…

AIM : To design the hood of a car with the given input Outer panel and its dimensions. Hood Introduction : The hood (North American English) or bonnet (Commonwealth English) is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment or trunk (boot in Commonwealth English)…

Automotive Wiring Harness using CATIA V5 - Challenges   Project 1   Statement of assignment:- Route the Wiring harness on Given Engine and Prepare to flatten the view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply…

Aim: To develop the car Backdoor(Tail gate) with the reference of given skin data as perengineering standared by using catia v5  Back Door :The Back door is typically hinged, but sometimes attached by other mechanisms suchas tracks, in front of an opening which is used for entering and exiting a vehicle.A vehicle…

Automotive Wiring Harness using CATIA V5 - Challenges   Project 2   Aim:- Statement of assignment: Route the Wiring harness on the Given car body and Prepare to flatten the view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.…

AIM:-- For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs.…

Section modulus is the measure of the strength of any section with respect to neutral axis. The strength is measured by the section modulus formula. S=I/Y Were S: suction modulus I: moment of inertia       resistnce offered to any load creating moment , bending or twisting. Y : distance from neutral…

                         Automotive Interior Door Trim Panel Design With Master Section                                       Aim:      …

Aim : Route the Given harness layout in Electrical workbench & Apply the Conditions. Ojectives : Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc Check for the bundle warning. Add snap. Generate CAT.part of harness…

Aim: 1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors: DT06-4S DT06-6S DT06-2S DT06-08SA       Steps Download connector 3D data from te.com Converting…

Aim: 1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors: DT06-4S DT06-6S DT06-2S DT06-08SA       Steps Download connector 3D data from te.com Converting…

  Underbody Coating Underbody coating is a dense protective layer of coating applied to the underside of an automobile and it is also called as an anti-rust or anti-corrosion coating. In Indian road conditions, the car’s underbody is most prone to corrosion. Hence the coating provides a long term protection…

1. Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place Madurai…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Create the Points and Planes in Part Design Work Bench. Define the part as support in Eletrical Part Design Workbench. Select the point and Plane for First entry point and Select…

Create/Download Connector 3D - The 3D model of the connector is downloaded from websites or created manually.  Create required Geometrical Parameters - The required geometrical parameters like Connector Point, Bundle Entry Point, Cavity Point, Connector Axis, Cavity Axis, etc are created. …

                         Automotive Interior Door Trim Panel Design With Master SectionAim:        The project aims to design and develop the Automotive Interior Door Trim Panel with engineering features like Haet Stakes, Push Pin,…

                                                    ASSEMBLY WORKBENCH   1.QUICK RETURN MECHANISM:                        …

                      A pillar Design with Master Section Objective of the Project:                                        Create A Pillar plastic component with…

                                DOOR TRIM LOWER WITH ENGINEERING FEATURES   Objective: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface…

                                                                      Door Trim with Dog House Attachment  Objective:  Create the…

                                                         Drill handle with Attachment Feature Creation (Ribs & Screw Boss)   Objective:   Create the rib for the…

                                           Door Trim AND DRAFT ANALYSIS  Objective: Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the…

                                                                                           …

COIN HOLDER DESIGN AND DRAFT ANALYSIS   Objective:      Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on…

Objective:        Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.      …

Objective: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given Class A Surface: Creating Tooling Axis:…