Week 8 - Challenge 2 - Base Bracket Design

Underbody Coating: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years, it’s…

BENCHMARKING: Benchmarrking is a process of measuring the performance of a company's products,services or processes against those of another business  considered to bee the best industry.'best in class'. the point of benchmarking is to identify internal opportunities for improvement.by studying companies with superior…

AIM:        TO CREATE A DOOR ARMREST WITH THE 2.5mm THICKNESS. CLASS A SURFACE:          Joining all the surfaces and the merging distance should be 0.001mm. TOOLING AXIS:           Creating a tooling axis in Z-direction.at first creating a point and…

FINAL REPORT FOR THE PROJECT: DEVELOPMENT OF DOOR TRIM PANEL: AIM:        To design and development of vehicle interior door trim using CATIA V5 with the given class A surface along with the master section. Also create the side attachment features ass per design rules. OBJECTIVE:      *To…

ISOMETRIC VIEW:

AIM:    To create the B pillar solid from the class A surface in catia V5. SOFTWARE USED: CATIA V5. OBJECTIVES:     *Create a ssketch using the positioned sketch.     *All the sketch should be iso constrained.     *Ensure proper tree structure.     *Geometrical set should…

AIM:    TO Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the Heat Stakes and the locators…

AIM:         To Create the Screw boss  and Dog House for the Centre console coin holder PROCEDURE: SCREW BOSS: * Create a geomentrical as the SCREW BOSS. *Create a  positioned sketch to create circle for the screw boss. *Draw a  two circle with 5.2 and 8.2 mm as diameter. *sketch should be iso constrained. *Insert a body…

 AIM: TO Create the rib for the Centre console coin holder considering the design. PROCEDURE: 1.Create a geometrical set as RIB DESIGN. 2.Now,extract the base back surface to create a rib. 3.create a positioned sketch. 4.create a line and the line should be iso constrained. 5.now,extrude the line for the given mm.…

AIM:        Design the core and cavity of the SWITCH BEZEL. SOFTWARE USED: CATIA V5 DRAFTING ANALYSIS:         The draft analysis command enables you to  detect if the part your DRAFTED  will be easy to removed.this type of ANALYSIS is performed based on color ranges…

AIM:   To create a center console coin holder and add the thickness to it and generate the draft analysis on a solid surface.   PROCEDURE:   check for any openings in the given center console coin holder model by  using In BOUNDARY>SELECT EDGES-select the surface to create the boundary at the opening.…

AIM:  TO Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. TOOLBAR USED: EXTRACT UNTRIM  EXTRAPOL …

ISOMETRIC VIEW: FRONT VIEW: SIDE VIEW: TOP VIEW:    

ISOMETRIC VIEW: TOP VIEW: FRONT VIEW: SIDE VIEW:

 AIM:    To study and analyse the BAJA all terrain vehicle (ATV) model using simulink and compare between difference models. OBJECTIVES:     Carry out a system-level simulation of all-terrain vehicle and prepare report explaning the model properties&comment on the results. ALL TERRAIN VEHICLE:…

2. Make a Simulink chart for the “Gear shift” logic as per below conditions:         Speed Range(kmph)        Gear                0 to 15       …

AIM:     1.Make a Simulink model of Doorbell using solenoid block.      2.To make the simulink Using a thermistor to sense the temperature of a heater & turn on or turn off the fan.  SOLENOID:          A solenoid  is a type of electromagnet,…

AIM:        Create a rankine cycle simulator plot T-S and H-S diahgram. THEROY:             The Rankine cycle closely describes the process by which steam engines commonly found in thermal POWER GENERATION PLANT harness the thermal energy of a fuel or other heat source…

AIM:        Parsing NASA thermodynamic data in matlab. DATA PARSING:         it refers to the process of converting information represented in one form another form to make it easier to work with.it is done by first partially analysing the data,understanding its logic and structure,then…

AIM:-         TO solve a program for stalagmite model for the genetic algorithm by using  MATLAB. OBJECTIVE OF THE PROJECT:-           The main objective of the project is to find the minimum value of the stalagmite function with respective to the number of iteration given…

  AIM:-          To write a program that solves the equation of the motion of a simple pendulum with damping. THEORY:-                A second order differential ordinary equation is which any derivatives with respect to the independent variab;le have order no greater than 2. SIMPLE PENDULUM:-               An ideal pendulum…