Week 11 - Project - A pillar Design with Master Section

Routing for side door panelRoute the wire for the side door of a care with the necessary connector along with the guiding challenge data given TASK Routing assembly creation Flattening Drawing creation  Different connectors to be used :  Interconnection connector Connector -…

Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. As given task the wiring harness flatting is done from week challenge the below are the challenge related images wiring harness…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…

oute the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download connector…

 Download the following cad data & define it as Electrical support using the Electrical Part Design Workbench. Define all the necessary properties. As given data P-Clamp is downloaded as a mechanical part it acts as a support to the wire bundle here it contains the entry face and exit face where it has different…

Download the following connectors & Connector clip cad data from the given link & define it as Electrical Connector using the Electrical Part Design Workbench. Define all the necessary properties of Connectors & Clip.         As given above question first, the downloaded part is added to…

Assemble and apply GD&T to the butterfly valve assembly drawing   assemble of butterfly valve is designed with all proper constraints and GD&T is applied to the designed assembly 

Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses   Make sure that the assembly file and part files ( Outer panel, Inner panel, and Reinforcements) are in the same folder before zipping the folder and submitting it…

For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs. Suggest…

Introduction to Fender: Fender is the vehicle part which covers the wheel and the engine compartment. The fender is provided in such a way that it will protect the padestrians from the high impact from the engine comapartment. The fender is also the cover made in such a way that the customer won't see the internal ugly…

             Wheel arc calculation is necessary for the fender design to pass the local regulation which are based on the local road conditions.             Wheel arch is a semi-circular area in fender, which houses the wheel well.…

                            Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. There are two type of section modulus .elastic section modulus Plastic section moduls For general design, the…

as the given guidelines hood assembly created

 Under body coating:                Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically accessible but are prone to corrosion.  …

Benching marking: this is the initial stage of automotive development. It is the comparison of one property to the other and one design to the other for the new product and for the new design. List of cars for 5 seater: Tata Nexon It is the 5 seater car it is in the range of 7.79lakhs to 11.3 lakhs as the specification…

From the given master section and class A surface the parts are thicken to 2.5 mm distance and with the draft angle of 3 drgress with the tooling axis and the doog house is created with the help of side core axis  draft angle is given for every part 3 degress  heat steak,4 way locatorsand 2 way locators are placed…

As given question ppt and part body is made and attached 

tooling axis is made by extrcting the surface and bisecting the lines on both sides of edges  front view of the door trim top view of the door trim side view of the door trim

tooling axis is created by taking the class A as a reference by extracitng the class A surface the above picture is class B  surface with differents opertions class C surface is given above the above picture is front view of te door trim the above picture is top view of the door view  the abov picture is side…

tooling axis is created by taking class A surface as a reference and exracting the base gives the surface and placing the point on the surface gives the tooling axis

Answred to the given quetions with out screenshots the given link are compressed zip folder with all CATpart and CATproduct

At the intial stage the draft angle of class a surface is 3 degree at every point after triming every surface  after changing the draft angel from 3 to 2.9 degree the analysis on wall got changed and colour changed to green  due to tooling axis change the wall draft angle got changed by

for the given sketch draft angle is 2 degrees so that changed to 3 degrees at below At every point draft angle is mesured to be 3 degree and futher draft analysis is done at different points on class A after the draft analysis tooling is made interseting profile anf by using bisecting lines option now the process…