Week 10 - Challenge 3 - Door Trim Lower with Engineering Features

BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance.For example, it can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer tests and reviews.These look at products and services and provide…

https://drive.google.com/file/d/1WazF6ZlLbMoO1ow1acKGBdRcZzEzgmLC/view?usp=drive_link Since the updation of Skill-Lync's new UI I am not able to upload my challenge file, So I created a Google Drive link for my final projct challenge file, Please consider the files available through the above link for grading of the challenge.…

Objective The objective of this project is to model a butterfly valve and apply GD&T to the different parts and assembly of the butterfly valve.  Introduction A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start a flow. Butterfly valves are easy and fast to open. A 90°…

Automotive Roof Design Aim: To design & develop the Roof of a car with its components by following the master section and design parameters. Objective: For the given Car Roof styling, design and develop the essential flanges and reinforcements, namely the Front Roof Rail, Rear Roof Rail, Centre Roof Rail and Bow-Roofs.…

FENDER DESIGN AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. INTRODUCTION : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well. Its primary propose is to prevent sand,…

FENDER WHEEL ARCH CHALLENGE FENDER WHEEL ARCH Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The design of the wheel arch of the fender should be such that it must shield wheels and protect both passengers compartment and pedestarians from the projection of watr, mud and stones.The…

Section modulus is a geometric property of a cross-sectional shape that measures its resistance to bending. It quantifies the shape's ability to withstand applied bending moments without excessive deflection or failure. The section modulus is an important parameter used in structural engineering and design calculations.…

The car hood, also known as the bonnet in some regions, is a crucial component of a vehicle's exterior. It is the panel that covers and protects the engine compartment. The hood plays several important roles, including providing access to the engine for maintenance and repairs, contributing to the vehicle's overall aesthetics,…

UNDER BODY COATING: Underbody coating is usually a dense cladding applied uniformly to the undercarriage of the automobile. It is normally sprayed underneath of the car to prevent it from rusting small scratch of dents, The main purpose of undercoating is to check rust especially in the body components like frame…

DEVELOPMENT OF DOOR TRIM PANEL   OBJECTIVE: to make half of the door trim panel in catia-V5 from the provided Class-A surface and folloing the master section. APPROACH: Make tooling axis. Run draft analysis. Make B surface. Make C surface. Trim all together and make it a closed body. Create a solid body from…

TO CREATE A GIVEN PART BODY USING CLASS A SURFACE AND MASTER SECTION.   MASTER SECTION: Master Sections are the guides for design requirements that shape the component after Class A Surfaces' technical styling.   Here the master section and the class A surface has be provided, so we can create the class…

Note: Report attached along with the CAT part as PPT.   ISOMETRIC VIEW     FRONT VIEW   SIDE VIEW     TOOLING AXIS     DRAFT ANALYSIS ON CLASS A   DTAFT ANALYSIS ON SOLID PART     DRAFT ANALYSIS ON HEAT STAKE        

REPORT:   1) The main objective of this challenge was to create a solid part by creating CLASS B & C SURFACE and necessary DOG HOUSE for the given CLASS A SURFACE and perform a draft analysis on the solid part. 2) TOOLING AXIS: The first main step is to creatinf a tooling axis, the tooling axis can be…

TO CREATE THE CLASS B & C SIRFACE AND NECESSARY RIBS AND SCREW BOSSES FOR THE GIVEN CLASS A SURFACES AND PERFORM DRAFT ANALYYSIS. CLASS B SURFACE   CLASS C SURFACE     CLOSED SURFACE     TOOLING AXIS   DRAFT ANALYSIS ON CLASS A SURFACE   CLOSED SURFACE   SOLID PART   …

                      Note: The report is attached as PPT along With tha CAT Part

NOTE: Report attached as PPT with the cat part                                

Report Attached in the form of power point presentation along with the CAT Part.