Underbody Coating

     ABOUT LENS Lens is an optical material that controls the light emitted from a light source and allows it to distribute in a certain angle and density. Lenses provide precision control over light angle. Lenses can be made of plastic, silicon or glass material in various shapes and sizes.  …

Operation to do: Joining of Class A surface. Create Tooling Axis. Create Draft Analysis for Class A Surface. Create Class B Surface. Create Class C Surface. Create Final Product. Material used in Lens: Poly Carbonate. Followed Constrains: The change in dimension of the Class A Surafce is not allowed. Change in thickness…

Aim: Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and industry based…

Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…

  Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness A and Harness B as…

Aim: To design a Backdoor of the car on sheet metal using the appropriate design and provided skin data by considering design rules. Objective: To design the backdoor with design methodologies and and provide the emboses,reinforcements in the inner panel and side relief in outer panel to increase the strength. Theory:…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

    Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit point. create planes at two points and another at base. Switch…

  AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Electrical Connector using Electrical Part design Workbench. Define all the necessary…

Introduction: An automobile roof is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Though it just looks like a styling surface that protects from sun, wind and other elements, various environmental conditions are…

FENDER DESIGN AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. FENDER It is an aesthetic component/part of a car that frames the wheels. Prevention of sand,  mud particles, and other road contaminants from being thrown into the engine…

  Aim: To calculate the Fender Wheel Arch area , to pass the European standards. Objective:  Create the intersection point according to given degree angle. Follow the European standards to prove the design is valid.  Tabulate the result to conculde the final result. Introduction: Its primary purpose is to…

                                                            Section Modulus Calculation Of Hood Aim  To calculate the section modulus of the previously designed…

                                                          CAR HOOD DESIGN   Aim:  To design car hood in NX using given master section and provided design parameters.   Introduction The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk…

AIM: Study the underbody coating used in automobile industries. Objectives: Study about underbody coating Study about types of underbody coating and its advantages and disadvantages. Procedure: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile.…

Requirement:  Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His family comprises five members including his wife, five-year-old boy, his father, and his mother. He visits his native place Madurai which is 500kms away from Bangalore once in a month. Also, he will be…

Objective:- To created the 3D part of the butterfly valve sub part name like, Main Body, Shaft, Lever, Nut , Screw, Disc Plate etc. To apply Geometric Dimensioning and Tolerancing (GD&T or GD and T) to the betterfly valve assembly drawing. To understand the concept of Geometric Dimensioning and Tolerancing…

                                          DEVELOPMENT OF DOOR TRIM PANEL AIM To design and development of vehicle interior door trim using given class A surface along with master section. Also create the side attachment features as per design rules. OBJECTIVE To create the thickened part using master section for reference.…

DESIGNING A PILLAR USING MASTER SECTION OBJECTIVES To improvise the Class A surface by resolving bad patches and adding flanges to it.  To create A pillar solid model with the help of  improvised class A surface. To create B side features for the A Pillar using the master section given to us as an input. To create…

DOOR TRIM LOWER Aim: To Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Introduction : The input of the product…

Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and…

AIM Create the component through the given Class-A surface.  the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the rib and screw boss as by considering the design rules   CLASS A…

Aim/Objectives: Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. Steps Followed: Tooling Axis creation Checking Draft analysis for created tooling Axis Creating parting Surface Creating Core Side Creating cavity side. 1). Tooling Axis: The class A surface is Extracted Then…

TO DESIGN A CAR BUMPER BY USING CLASS A SURFACE  AIM:  To design a car bumper Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add…

 DESIGN OF COIN HOLDER AIM:  To create the coin holder plastic component through the given Class A surface. To begin with, the tooling axis for the given Class-A surface should be created meeting the requirements of the draft angle and at the end perform the draft analysis on the model. Take the thickness of…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL  Aim: This project aims to create a switch bezel plastic component using the given class A surface following the OEM standard. and perform the draft analysis. Class A-surface   Objective: Ensure Proper Tree Structure. Geometrical sets should have a proper name based…

BASE BRACKET DESIGN BY USING CLASS A SURFACE  AIM:  To design a Base Bracket Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add draft…