Tool Test 1

week-6 Calculate the Stretch Ratio by comparing the ELFORM (-2,-1,1,2) with Ogden_Material Model. Aim: Simulate the given model with different elemental formulations by assigning the appropriate key cards and calculate strech ratios. Explanation:  The given model has only the material data and this…

                                                              MODELLING SPOTWELDS USING 1D BEAM AND 3D HEXA SOLID ELEMENTS            …

  CRASH BOX SIMULATION  AIM: To create a complete simulation file for crash analysis of crash box having two different thickness of 1.2 mm and 1.5 mm from the given FE model of crashbox and produce the following deliverables.  1.Input. k file and output files (D3PLOT, GLSTAT, SLEOUT, RCFORC) 2.Animation…

AIM: To create a complete simulation file to perform a drop test from given basic .k file consisting of only nodes and elements. Essential keywords should be added to create a basic solver deck to simulate a drop test.   PROCEDURE: Open the LS-PrePost and open the given keyword file. The given input file consists…

AIM             To study about implicit and explicit method to solve engineering problems. OBJECTIVES             To demonstrated in the PDF, F(u) = u3+9u2+4u use this equation and solve using both…

Aim : Convert given measurements into different system of units and finding their corresponding conversion factors. Measurements given : MASS 1kg LENGTH 1m TIME 1s FORCE 1N STRESS 1Pa ENERGY 1Nm DENSITY 1Kg/m3 YOUNG'S Modulus  210GPa Velocity 56.33KMPH GRAVITY 9.8m/s2 System Of Units : Kg cm ms Kg cm s gm…

                                                                    VOLUME MESH GENERATION AND DEPLOYING CONNECTIONS FOR CAR REAR SUSPENSION   OBJECTIVE: Importing rear car suspension geometry into ANSA. Clean up the geometry until no topological error is found. Generate mid surface for required parts. Generate volume…

Aim : For the given component checking the geometrical errors and meshing the model with given quality criteria. After meshing thickness as to be assigned. S.No     Quality Criteria  Value        1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length 6 4 Aspect  3 5 Warpage 15 6 Skewness 45 7 Jacobian  0.7 8…

     CONNECTIONS REPRESENTATIONS OF REAR DOOR   OBJECTIVE:-  To perform the connections of the rear door of the car with different connections                             techniques. PROCEDURE:- Input the files rear…

AIM: To do a pre-processing on a given Rearview mirror component model using ANSA. OBJECTIVE: To check the geometrical error on the Rearview mirror model. To generate 2D mesh on the components based on the quality criteria given. To generate volume mesh on the component using tetra elements. PROCEDURE: IMPORTING THE CAD…

Objectives: The objective of this project is to performing meshing for Tool test 1 for component1 & Component 2 using the ANSA tool. From the given Component, Checking geometrical errors and mesh with given element quality criteria Extracting the mid surface from the component. After meshing the component the thickness…

AIM: The main aim of the challenge is to the morph the given model. OBJECTIVE: Performing the morphing on the two models. increasing the height of the dog houses and ribs of the 2nd model. understanding the various application of the morphing in various industries. MODEL 1: PROCEDURE: First import the cad model. Then extract…

AIM: To do a pre-processing on a given rearview mirror component model using ansa. OBJECTIVE: To check the geometrical error on the rearview mirror model. To generate 2D mesh on the components based on the quality criteria given. To generate volume mesh on the component using tetra elements. PROCEDURE: IMPORTING THE CAD…

AIM: To extract the mid surface and mesh the given bottle cap component using given quality criteria and assign correct thickness to the property. OBJECTIVE: S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  3 4 Aspect  3 5 Warpage…

AIM: To mesh the given hood components using quality criteria after cleanup the geometry and extract the midsurface . OBJECTIVE: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  2 3 Maximum Length  7 4 Aspect  3 5 Warpage 15 6 Skewness 45 7 Jacobian …

Project 2-Meshing of Rear Wheel Holder AIM:    To extract a mid surface and mesh the given component. GIVEN MODEL: OBJECTIVE: To geometrically clean the model for any error on it. To extract a midsurface of the component. To clean and defeature the mid surface so as to avoid any minimum length errors while meshing.…

AIM: To extract the mid surface of given plastic component and mesh the component under given quality criteria and assign thickness. OBJECTIVE: To extract the mid surface and mesh it with proper mesh flow. To ensure the mesh should pass the given quality criteria. To assign thickness to all the components of the model.…

CREATION OF 1D CONNECTORS AIM: Meshing of the given geometry. Provided below are the quality parameters that you have to follow. OBJECTIVE: The objective is to generate the mesh on the given model by following the quality criteria and creating the connectors and attach the various parts of the given model. 1. Right_Rail_2…

3D TETRA MESHING AIM:             To perform 3D tetra mesh on the given models. OBJECTIVE: Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units,…

21 days planner   AIM: To extract mid-surface and generate mesh on hood using hyper mesh . GIVEN MODEL: PROCEDURE: STEPS INVOLVED: Importing geometry and cleanup. Extracting mid-surface and assigning properties. Meshing the surface with in the given quality criteria. QUALITY CRITERIA: Target Element Length = 5 Units…

AIM: To create 1D elements on the given component with given cross-section and DOF using hypermesh. Rod element: Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm                               dimension…

MODELLING AND ASSEMBLING OF SUNSEEKER PREDATOR YACHT Objective: The main objective is to produce a detailed model of different parts of blue prints and some given dimensions, and assembling the entire model. Introduction: Solidworks software is a mechanical cad software which helps the designers to show their idea of a…

AMERICAN CHOPPER   Objective:   The objective of this project is to creature a 3D model of the AMERICAN CHOPPER parts using different tools in the SOLIDWORKS. To assemble the different parts of the chopper modelled. To create a photorealistic rendered image of the chopper using Solid works Photo view 360.  …