Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings

INTRODUCTIONS:- Etabs is the software which is being used to create a structural model of given building. In the first step note down the values of grid spacing from the given structural plans. Next Create the Structural model and run the Model Analyse the result and note down the result values from ETABS. Next is to export…

1.AIM:Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. INTRODUCTION:      SI SAFE (Slab Analysis by the Finite Element Method) is the best tool for designing concrete slabs and foundations by the Computer and Structures,…

PROCEDURE: FOOTING:           Footings and other foundation units transfer loads from the structure to the soil or rock supporting the structure. Because the soil is generally much weaker than the concrete columns and walls that must be supported, the contact area between the soil and the footing is much larger than that…

AIM:The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs.   RESULT:

INTRODUCTION:    In Structural engineering,a Shear wall is a Vertical element of a system that is designed to resist in-plane lateral forces, typically wind and seismic loads. In many jurisdictions, the International Building Code and govern the design of shear walls. A shear wall resists loads parallel…

   INTRODUCTION:      Reinforcement detailing of column        The column is a very important part of buildings. Generally, they are used to transfer the load of the beams and slabs to the footing of the buildings. Therefore, it is very important to make it in a proper way that it can easily bear all loads which act over…

INTRODUCTION:           Reinforced concrete beams are structural elements that designed to carry transverse external loads. The loads cause bending moment, shear forces and in some cases torsion across their length.Moreover, concrete is strong in compression and very weak in tension. Thus, Steel reinforcement used to take…

1.AIM:           Factors influencing the dynamic characteristics of a building.           Factors influencing the Natural Period of a building.           Factors influencing the Mode shape of oscillations. INTRODUCTION: Factors influencing the dynamic…

1. AIM:To create column properties for different types of pedestal members and model in the grids created on week-1:   RESULT:By using the Tekla software we have created the Pedestal on the grids.The size of pedestal concrete column is 400*600 mm. 2. AIM:To create column properties for steel columns and model columns…

1. Project workspace. Scene content. Create two scene views. Loading drop list. Properties windows.   INTRODUCTION:           TSD-Tekla Structural Designer is a tool to analyze and design the RCC and Steel Structures.i.e.Modelling,Analysis,Design,Report generation and Drawing generation. PROJECT WORKSPACE: SCENE CONTENT:…

1.Model of 25 storey building on ETABS with the structural properties.Plinth floor level can be taken at a height of 1.5 metres from the base.Each of the successive 25 storeys has a storey height of 3 metres.   Dead load: Live Load: Earth quake load X direction: Earth quake load Y direction: Final output:    …

1. S.No.         Criteria                fig.1                     fig.2                 fig.3 1. Restraint of floor shirnkage Full restraints at all corners Corners are…

1. i)Symmetry: Investigation of the framing plan with to symmetry in X-direction:           If we split the plan on "Vertical half" , it will look mirrored.So we conclude the given plan is symmetric in X-direction. Investigation of the framing plan with to symmetry in Y-direction:    …

1.Diffrence between Static analysis and Dynamic analysis :              Dynamic analysis is the testing and evaluation of an application during runtime. Static analysis is the testing and evaluation of an application by examining the code without executing the application. Many software…

1.a) OBSERVATION:           Concrete crushed and the reinforcement is exposed on the image.Concrete spilled beyond the reinforcement which may be a sign of repture.Beam top portion looks a safe beacause of the flange advantage from the slab.The crack develops from bottom to top means rebar " yielding "will…

Aim:To create a layout Plan and elevation diagram by using AitoCad software. Procedure: First of all we have to set the units by using in and enter command in the command box. Set the value of decimal and dimensions is Mm. Then Draw thr perpendicular and horizontal line by using line command is that L+enter . Draw the…

1.AIM:To create the layouts of the Kitchen and provide hatches pattern. Procedure: First ofall we have to set the units by usinh un +enter in command box. Now we use mm in scale,Then we have to create a rectangle horizontal distance is 4730 mm dia and then vertical distance is 3630 mm . The outter wall thick ness is 70mm…

1.Aim:To create a template by using Autocad software. Procedure: In AutoCad first step is to set the units,Then next step is we have to create a tabel by using command the command is TABLE + ENTER . After enter the command the dialoge box should be opened in that we set the required amount of rows and columns…

Aim:To create a floor plan,Elevation,Sections,Column,Beam and Footing plan into the given surface . Procedure: Firstoff all we wants to set the units we seted as decimal and the value is feet. Draw the vertical line at the distance is 20 feet and horizontal is 60 feet ,by using L + enter (or) select line on draw tool.…