Hood design-Week 2

AIM:   To solve the above assignment questions and define the necessary electrical properties in the respective workbench.   OBJECTIVE:   To download the P-Clamp CAD data and define it as Electrical Support in the Electrical Part design workbench and also define the necessary electrical properties. To download…

AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.   DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Wiring harness routing shall provide ease in manufacturing, accessibility,…

Aim: To route the wiring harness on the given tailgate assembly and prepare the flatten view drawing in CATIA V5.  Given: Car Tailgate Assembly                                              …

As per the image attached below wiring harness assembly is created according to the layout mentioned above with all the connectors are electrically defined and with corrugated tubes added to necessary bundles. After that the CAT product file of harness assembly is exracted to flattening workbench where all the flattening…

     The objective of this project is to first route the two Harness A and Harness B as per the given harness layout. The electrical connectors are represented by numbers in the above figure. There are 8 different types of connectors at 10 different locations.      Bundle continuity has to…

The connectors is define as Connector connection point Bundle connection point Axis system of the connector connection point Define the all connectors as electrical components The connectors are assembled by given layout drawing We use the multi branchable to add all the necessary branches, branch points in the wiring…

1)Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Firstly we have to download the 3D CAD model of P-Clamp from the link which is provided above. Extract the Zipper file and open it in the CATIA V5. Open the CATIA V5 and click…

1)Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Firstly we have to download the 3D CAD model of P-Clamp from the link which is provided above. Extract the Zipper file and open it in the CATIA V5. Open the CATIA V5 and click…

sign part. shown in above fig. In contact select the face on which point is created and for coincidence and orientation y-axis and x-axis respectively. Then select ok. So, it is ready for assembly for mounting of clip. Procedure for mounting clip Download the part by given link. Go to mechanical design and then part design.…

Create the Dog House for the Door Trim considering the design rules mentioned in the video.  "C" is where the doghouse contacts the backside of the surface  Doghouse wall thickness at the intersection of the part wall ( C ) should be 40% or less than the main wall stock ( T ).  The height of  ( B )…

Create the rib for the Drill Handle considering the design rules mentioned in the video.  Create the Screw boss for the Drill Handle considering the design rules mentioned in the video.  General Guidelines for Bosses:   Draft  - 0.5 degrees on the walls of boss   Thickness -  Typically…

Backdoor Introduction: An automobile back door or Tailgate is the panel that covers the boot (or trunk) of an automobile. It enables access to the main luggage compartment. A hinge allows the boot lid to be raised, while devices such as springs or gas cylinders hold it up in the open position The Backdoor is an assembly…

Backdoor Introduction: An automobile back door or Tailgate is the panel that covers the boot (or trunk) of an automobile. It enables access to the main luggage compartment. A hinge allows the boot lid to be raised, while devices such as springs or gas cylinders hold it up in the open position The Backdoor is an assembly…

Bow–Roof condition Snow Load condition

  0

DESIGN OF CAR FENDER Fender is the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fender is  the part of an automobile,…

Japan regulation Europe regulation us regulation mostly europe regulation is for all conditions becouse in regulation the length is max than remining regulations ie... l>=10 and a>5  report For length L distance betwen fender face and wheel                  …

Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear,radius of gyration for compression, and moment of inettia and polar moment of inettia for stiffness. MOI = 9.425*10^3 mm^4 Y= 51.6821…

sir i dont compltet my assembly   

Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh off the lot and spotless, it is usually sprayed or painted on. But it’s acceptable if you apply the undercoating after a couple of years. This is because it might protect…

1. honda wr-v is best due to mileage is super 24 kmpl as per interst it a big car 2. kia sonet is also same as honda but best in prise kia on road price is 8.5 l it super car i saget this car 3. tata nexon is best in this prise and elctric mode also avilable on road price is 9l  4. maruti suzuki ertiga is the high…