Final Project: Electric Rickshaw modelling

Objective of Main Project: Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD creation, Configuration Parameter changes, Model Advisor check & Code Generation. In Configuration Parameters:…

Objective of Mini Project:- Development of MATLAB Simulink model as per requirement. Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems is fine. MBD compliant changes, Data Dictionary creation & code generation is added advantage, and that is not…

Objective:- Create a MATLAB model of electric car which uses lithium ion battery and suitable motor. Choose suitable blocks from Simscape or Powertrain block set. Implement the vehicle speed control using PI controller and generate brake and accelerator commands. Avoid using readymade driver block for speed control. Prepare…

Objective:- Create a detailed MATLAB model of an electric rickshaw (three wheel passenger vehicle) as per details below:  Rear wheels driven by PM brushed type motor Assume efficiency points of motor controller and motor Make an excel sheet of all input and assumed data  Results: For any three standard driving…

  Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters    …

Objective:- For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. Result:-  Introduction:- This example shows how to simulate a battery pack consisting of multiple series-connected…

Objective:- Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. Introduction:-  A123’s high-performance Nanophosphate lithium iron phosphate (LiFePO4) battery technology delivers high power and energydensity combined…

Objective:-  https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb…

Objective 1:- Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it?   Result:-  Before creating table for different types of cells we need to understand the Li-ion…

Part A:- Overview:-  What are air crafts and which are types of aircrafts, you know? Most of us will only answer the common ones – airplanes and helicopters. Well, yes, you are not wrong. Airplanes and helicopters are the most common types of aircrafts we may know. But what you may miss out on are different…

Objective 1:- For a defined driving cycle, calculate the energy required for braking. For calculating the drive cyle i have taken an example of drive cycle where i have imported the excel value of Time(sec) & Velocity(mph) to calculate the braking energy.  Matlab Script:-  %program to find the braking energy…

Objective 1:-  (A) Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’. Introduction:-  A DC motor controller has many forms.Here we are learning an h-bridge motor driver circuit. So what? It is easy to do with a transistor or MOSFET drivers. And they are high performance, too. Firstly we…

Objective 1:- Which types of power converter circuits are employed in electric and hybrid electric vehicle?   Introduction:- We have different types of coverter which are using in the Electric vehicle. As we know we drive EV by motor or by motor & engine. In both the cases we required battery source. Battery…

Objective 1:- What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type? Definition is based on IC engine example.  Mapped:- Model uses a set of steady-state lookup tables to characterize engine performance. The tables provide overall engine characteristics,…

Objective 1:- For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can thevehicle travel for 45 km with FTP drive cycle? Conclude your observations.Introduction- The tool Advisor developed in November 1994 by the NREL. It helps to analyse theconventional, Hybrid electric and fuel cell vehicle.…

Objective- Analyzing of the technical report of Baja All Terran Vehicle which involves model properties their configuration, their behavior with and without lookup table. Analyze the data at different gear ratio where we need to see at which gear ratio our AVT vehicle will be running perfectly.   Introduction of Baja AVT-…

Week 4, Task 1-:Objective- My objective of the task is to create control logic of washing machine usingstateflow.Condition- For the activation of the system we need power supply and for running themachine we need water supply. Both of the things are compulsory. If the water supply willbe stop during the process then process…

WEEK 2 TASK 1-Objective- Make a Simulink model of Doorbell using solenoid block with the following details:1)- In this Model i have used Pulse generator as to make arrangments to make it on for 2 sec to enable a switch for the operation of Solenoid.I made this Source arrangment by controlling the pulse delay and pulse…